Search

Due to the enhanced price of electricity, the gradual depletion of fossil fuels, and the global warming concerns, power loss minimization through deployment of distributed generators (DGs) has attracted significant attention in recent decades. This paper proposes a genetic algorithm (GA) based strategy for minimization of active and reactive power losses through optimal location and size of DGs. It also quantifies and tallies the total network power losses for the cases with random as well as optimal allocation of DGs. To validate the accuracy of the obtained results from GA, another nature‐inspired optimization algorithm, cuckoo search, is also deployed. The simulation results on IEEE 30 and 118 bus systems indicate that the proposed strategy not only can effectively reduce the total network active and reactive power losses but also lead to the improvement of network voltage profile. [ABSTRACT FROM AUTHOR]

This paper presents a novel load shedding scheme with consideration of the active power ramping capability of Distributed Energy Resources (DERs) to address the challenges due to low inertia and diverse types of DERs in microgrids. In the paper, it is demonstrated that due to the small inertia in microgrids, even with sufficient reserve power, the frequency could rapidly drop to a low level and trigger the DERs’ under frequency protection (thus the total system collapse), if the reserve active power is not ramped up at a sufficient rate. The proposed load shedding scheme addresses this challenge by considering not only the DERs’ reserve, but also their speed in injecting active power to the system to determine the amount of load should be shed, so that critical frequency thresholds are not violated. The proposed load shedding scheme is tested using a realistic real time hardware-in-the-loop arrangement. The results show that the proposed scheme can correctly detect the cases when the DERs’ responses are too slow and trigger the required load shedding actions, thus effectively containing the frequency above the critical threshold. [ABSTRACT FROM AUTHOR]

Power-hardware-in-the-loop (PHIL) is a vital technique for realistic testing of prototype systems. While the application of power electronics-based amplifiers to enable PHIL capability has been widely reported, the use of motor-generator (MG) sets as the PHIL interfaces has not been fully investigated. This article presents the realization of the first MW-scale PHIL setup using an MG set as the power amplifier, which offers a promising solution for testing novel systems for the integration of distributed energy resources. Uniquely, this article presents a methodology that introduces augmented frequency and phase control loops that can be integrated to commercially-available MG set's existing frequency controller for precise frequency and phase tracking. Internal model control is used for the controllers design and tuning. The developed control algorithm is tested in a MW-scale MG set that couples a Great Britain (GB) transmission network model simulated in a real time simulator to an 11 kV distribution network. Experimental results are presented, which demonstrate that the proposed control methodology is highly effective in maintaining the synchronization between the simulated and physical systems, thereby capable of enabling the MG set as a PHIL interface. [ABSTRACT FROM AUTHOR]

• The paper examines the role of LV monitoring in MV fault localisation. • Secondary substations provide ground to ICT technologies for this purpose. • An algorithm deploying sparse LV measurements has been developed. • The distributed devices do not require time synchronisation reducing cost. • The results of this study demonstrate the robustness of the technique. A medium voltage (MV) faulted section location technique depending solely on unsynchronized low voltage (LV) measurements in distribution systems is introduced in this paper. The proposed method identifies the faulted MV feeder segment when an unsymmetrical MV fault occurs. It exploits parameters including voltage magnitude, angle and sequence components captured via distributed non-synchronized monitoring devices connected at secondary substations. In this study, the characterization of a system's LV profile during MV faults was achieved throughout both software simulations and physical testing. The latter was conducted in the 11 kV and LV distribution network of the Power Networks Demonstration Centre (PNDC) of the University of Strathclyde. The tests were performed for both 11 kV radial and ring network configurations. Modelling and simulations implemented using the DigSILENT PowerFactory package, complemented the hardware level testing and provided the opportunity for further examinations, such as the impact of MV laterals connection, distributed energy resources on both MV and LV side as well as the presence of unbalanced loads. Finally, the paper evaluates the effectiveness of the proposed faulted section location technique under various physical and simulated fault scenarios, loss of communications and noise interference. [ABSTRACT FROM AUTHOR]