Search

Despite the wide use of aliphatic polyesters, such as poly(L-lactic acid) (PLLA) and poly(ε-caprolactone) (PCL), for many biomedical applications, these materials are limited due to their hydrophobic properties and lack of functional groups to bond with ligands to enhance the cell reorganization. Recently, a composite consisting of bioglass and PCL was demonstrated to enhance the mechanical strength and to improve the degradation rate. Although numerous approaches have been developed to improve the wettability of aliphatic polyesters to create a favorable interface with cells, only few surface modification methods can be independently applied to surfaces with different material. In this work, mesoporous bioglass (MBG) nanoparticles embedded in PCL films were modified by the polymerization of aminomalonitrile (AMN) with 3,4,5-trihydroxybenzaldehyde (THBA). The copolymer layer was further utilized as a mediator to conjugate chitosan and evaluate the antibacterial efficacy. Our results show that the hydrophilicity of the composite membranes significantly improved after treatment. In addition, after immersion in simulated body fluid (SBF) for 14 days, hydroxyapatite formation was only observed on the treated membranes. This result demonstrates that the surface treatment did not alter the MBG bioactivity. Moreover, the cell culture results reveal that the extension level of cells and expression of alkaline phosphatase activity (ALP) of osteoblast-like (MG63) cells were higher on treated composite films compared to untreated ones. The results imply that the treatment procedure can be simultaneously and homogeneously applied to the organic/inorganic composites. In addition, Staphylococcus aureus adhesion on AMN-co-THBA and chitosan/ AMN-co-THBA was significantly lower than untreated PCL. Moreover, the percentage of dead bacteria was highest on the chitosan/ AMN-co-THBA membranes. These results indicate that the AMN-co-THBA modification can be used in composite materials and complex constructs, and it provides a potential method to create versatile surface properties for biomedical applications., (Copyright © 2021 Elsevier B.V. All rights reserved.)

Porous silicon (pSi) nanomaterials are increasingly attractive for biomedical applications due to their promising properties such as simple and feasible fabrication procedures, tunable morphology, versatile surface modification routes, biocompatibility and biodegradability. This review focuses on recent advances in surface modification of pSi for controlled drug delivery applications. A range of functionalization strategies and fabrication methods for pSi-polymer hybrids are summarized. Surface engineering solutions such as stimuli-responsive polymer grafting, stealth coatings and active targeting modifications are highlighted as examples to demonstrate what can be achieved. Finally, the current status of engineered pSi nanomaterials for in vivo applications is reviewed and future prospects and challenges in drug-delivery applications are discussed.

Emulsion-templated (polyHIPE) scaffolds for bone tissue engineering were produced by photopolymerisation of a mixture of trimethylolpropane tris(3-mercaptopropionate) and dipentaerythritol penta-/hexa-acrylate in the presence of hydroxyapatite (HA) or strontium-modified hydroxyapatite (SrHA) nanoparticles. Porous and permeable polyHIPE materials were produced regardless of the type or incorporation level of the bioceramic, although higher loadings resulted in a larger average pore diameter. Inclusion of HA and SrHA into the scaffolds was confirmed by EDX-SEM, FTIR and XPS and quantified by thermogravimetry. Addition of HA to polyHIPE scaffolds significantly enhanced compressive strength (148-216 kPa) without affecting compressive modulus (2.34-2.58 MPa). The resulting materials were evaluated in vitro as scaffolds for the 3D culture of MG63 osteoblastic cells vs. a commercial 3D cell culture scaffold (Alvetex®). Cells were able to migrate throughout all scaffolds, achieving a high density by the end of the culture period (21 days). The presence of HA and in particular SrHA gave greatly enhanced cell proliferation, as determined by staining of histological sections and total protein assay (Bradford). Furthermore, Von Kossa and Alizarin Red staining demonstrated significant mineralisation from inclusion of bioceramics, even at the earliest time point (day 7). Production of alkaline phosphatase (ALP), an early osteogenic marker, was used to investigate the influence of HA and SrHA on cell function. ALP levels were significantly reduced on HA- and SrHA-modified scaffolds by day 7, which agrees with the observed early onset of mineralisation in the presence of the bioceramics. The presented data support our conclusions that HA and SrHA enhance osteoblastic cell proliferation on polyHIPE scaffolds and promote early mineralisation.

We describe a simple and solvent-free method to generate nitric oxide (NO)-releasing coatings by incorporating diazeniumdiolate (NONOate) into allylamine or diallylamine plasma polymer coatings. The resulting coatings demonstrate continuous release of NO for over 48 hours and are effective at reducing the adhesion and biofilm formation of medically-relevant Gram-negative and Gram-positive opportunistic pathogens.

Biofilm formation on medical implants and subsequent infections are a global problem. A great deal of effort has focused on developing chemical contrasts based on micro- and nanopatterning for studying and controlling cells and bacteria at surfaces. It has been known that micro- and nanopatterns on surfaces can influence biomolecule adsorption, and subsequent cell and bacterial adhesion. However, less focus has been on precisely controlling patterns to study the initial bacterial attachment mechanisms and subsequently how the patterning influences the role played by biomolecular adsorption on biofilm formation. In this work, the authors have used colloidal self-assembly in a confined area to pattern surfaces with colloidal crystals and used them as masks during allylamine plasma polymer (AAMpp) deposition to generate highly ordered patterns from the micro- to the nanoscale. Polyethylene glycol (PEG)-aldehyde was grafted to the plasma regions via "cloud point" grafting to prevent the attachment of bacteria on the plasma patterned surface regions, thereby controlling the adhesive sites by choice of the colloidal crystal morphology. Pseudomonas aeruginosa was chosen to study the bacterial interactions with these chemically patterned surfaces. Scanning electron microscope, x-ray photoelectron spectroscopy (XPS), atomic force microscopy, and epifluorescence microscopy were used for pattern characterization, surface chemical analysis, and imaging of attached bacteria. The AAMpp influenced bacterial attachment because of the amine groups displaying a positive charge. XPS results confirm the successful grafting of PEG on the AAMpp surfaces. The results showed that PEG patterns can be used as a surface for bacterial patterning including investigating the role of biomolecular patterning on bacterial attachment. These types of patterns are easy to fabricate and could be useful in further applications in biomedical research.

Anionic ring-opening polymerization of glycidol was initiated from activated glass, silicon, and porous silicon substrates to yield thin, ultralow-fouling hyperbranched polyglycerol (HPG) graft polymer coatings. Substrates were activated by deprotonation of surface-bound silanol functionalities. HPG polymerization was initiated upon the addition of freshly distilled glycidol to yield films in the nanometer thickness range. X-ray photoelectron spectroscopy, contact angle measurements, and ellipsometry were used to characterize the resulting coatings. The antifouling properties of HPG-coated surfaces were evaluated in terms of protein adsorption and the attachment of mammalian cells. The adsorption of bovine serum albumin and collagen type I was found to be reduced by as much as 97 and 91%, respectively, in comparison to untreated surfaces. Human glioblastoma and mouse fibroblast attachment was reduced by 99 and 98%, respectively. HPG-grafted substrates outperformed polyethylene glycol (PEG) grafted substrates of comparable thickness under the same incubation conditions. Our results demonstrate the effectiveness of antifouling HPG graft polymer coatings on a selected range of substrate materials and open the door for their use in biomedical applications.

We demonstrate the patterned biofunctionalization of antifouling hyperbranched polyglycerol (HPG) coatings on silicon and glass substrates. The ultralow fouling HPG coatings afforded straightforward chemical handles for rapid bioconjugation of amine containing biomolecular species. This was achieved by sodium periodate oxidation of terminal HPG diols to yield reactive aldehyde groups. Patterned microprinting of sodium periodate and cell adhesion mediating cyclic peptides containing the RGD sequence resulted in an array of covalently immobilized bioactive signals. When incubated with mouse fibroblasts, the HPG background resisted cell attachment whereas high density cell attachment was observed on the peptide spots, resulting in high-contrast cell microarrays. We also demonstrated single-step, in situ functionalization of the HPG coatings by printing periodate and peptide concurrently. Our results demonstrate the effectiveness of antifouling and functionalized HPG graft polymer coatings and establish their use in microarray applications for the first time.

The effective control over biointerfacial interactions is essential for a broad range of biomedical applications in vitro and in vivo such as biosensors, cell culture tools and implantable devices. Here, our aim was to develop a coating strategy that is transferable between different substrate materials and can effectively suppress nonspecific protein adsorption and hence reduce cell attachment while also presenting bioactive signals to enable specific cell-material interactions. In a first step an allylamine plasma polymer coating was applied, followed by the covalent immobilization of a macroinitiator carrying iniferter functionalities in the side chains. Subsequently, copolymers with different molar ratios of acrylamide and a polymerizable peptide containing the sequence Arg-Gly-Asp (RGD) were grafted via surface initiated free radical polymerization. X-ray photoelectron spectroscopy (XPS) was used to confirm the success of each coating step. The cellular response to these coatings was evaluated using L929 mouse fibroblast cell culture assays for up to 24 h. Cell attachment was significantly reduced on acrylamide homopolymer coatings and negative control surfaces representing a polymerizable peptide containing the nonbioactive Arg-Ala-Asp (RAD) sequence. In contrast, cell attachment was increased with increasing polymerizable RGD peptide ratios in the copolymer. The combination of acrylamide-terminated peptide sequences in combination with acrylamide provides a simple and versatile route to surfaces that combine low nonspecific protein adsorption and the display of controlled densities of bioactive signals and is expected to be translated into a number of biomedical applications in vitro and in vivo.

Background: The ability to present signalling molecules within a low fouling 3D environment that mimics the extracellular matrix is an important goal for a range of biomedical applications, both in vitro and in vivo. Cell responses can be triggered by non-specific protein interactions occurring on the surface of a biomaterial, which is an undesirable process when studying specific receptor-ligand interactions. It is therefore useful to present specific ligands of interest to cell surface receptors in a 3D environment that minimizes non-specific interactions with biomolecules, such as proteins., Method: In this study, surface-initiated atom transfer radical polymerization (SI-ATRP) of poly(ethylene glycol)-based monomers was carried out from the surface of electrospun fibers composed of a styrene/vinylbenzyl chloride copolymer. Surface initiated radical addition-fragmentation chain transfer (SI-RAFT) polymerisation was also carried out to generate bottle brush copolymer coatings consisting of poly(acrylic acid) and poly(acrylamide). These were grown from surface trithiocarbonate groups generated from the chloromethyl styrene moieties existing in the original synthesised polymer. XPS was used to characterise the surface composition of the fibers after grafting and after coupling with fluorine functional XPS labels., Results: Bottle brush type coatings were able to be produced by ATRP which consisted of poly(ethylene glycol) methacrylate and a terminal alkyne-functionalised monomer. The ATRP coatings showed reduced non-specific protein adsorption, as a result of effective PEG incorporation and pendant alkynes groups existing as part of the brushes allowed for further conjugation of via azide-alkyne Huisgen 1,3-dipolar cycloaddition. In the case of RAFT, carboxylic acid moieties were effectively coupled to an amine label via amide bond formation. In each case XPS analysis demonstrated that covalent immobilisation had effectively taken place., Conclusion: Overall, the studies presented an effective platform for the preparation of 3D scaffolds which contain effective conjugation sites for attachment of specific bioactive signals of interest, as well as actively reducing non-specific protein interactions.

Cubic phase lyotropic liquid crystalline colloidal dispersions (cubosomes) were surface-modified with seven polyelectrolyte layers using a layer-by-layer (LbL) approach. The first layer consisted of a copolymer synthesized from methacrylic acid and oleoyl methacrylate for enhanced incorporation within the bilayer of the cubic nanostructure. Six additional layers of poly(L-lysine) and poly(methacrylic acid) were then sequentially added, followed by a washing procedure to remove polymer aggregates from the soft matter particles. Polymer buildup was monitored via microelectrophoresis, dynamic light scattering, and small-angle X-ray scattering. Polymer-coated cubosomes were observed with cryo-transmission electron microscopy. A potential application of the modified nanostructured particles presented in this study is to reduce the burst-release effect associated with drug-loaded cubosomes. The effectiveness of this approach was demonstrated through loading and release results from a model hydrophilic small molecule (fluorescein).

The control of cell-material interactions is the key to a broad range of biomedical interactions. Gradient surfaces have recently been established as tools allowing the high-throughput screening and optimization of these interactions. In this paper, we show that plasma polymer gradients can reveal the subtle influence of surface chemistry on embryonic stem cell behavior and probe the mechanisms by which this occurs. Lateral gradients of surface chemistry were generated by plasma polymerization of diethylene glycol dimethyl ether on top of a substrate coated with an acrylic acid plasma polymer using a tilted slide as a mask. Gradient surfaces were characterized by X-ray photoelectron spectroscopy, infrared microscopy mapping and profilometry. By changing the plasma polymerization time, the gradient profile could be easily manipulated. To demonstrate the utility of these surfaces for the screening of cell-material interactions, we studied the response of mouse embryonic stem (ES) cells to these gradients and compared the performance of different plasma polymerization times during gradient fabrication. We observed a strong correlation between surface chemistry and cell attachment, colony size and retention of stem cell markers. Cell adhesion and colony formation showed striking differences on gradients with different plasma polymer deposition times. Deposition time influenced the depth of the plasma film deposited and the relative position of surface functional group density on the substrate, but not the range of plasma-generated species., (Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.)

Control over cell-material surface interactions is the key to many new and improved biomedical devices. It can only be achieved if interactions that are mediated by nonspecifically adsorbed serum proteins are minimized and if cells instead respond to specific ligand molecules presented on the surface. Here, we present a simple yet effective surface modification method that allows for the covalent coupling and presentation of specific biological signals on coatings which have significantly reduced nonspecific biointerfacial interactions. To achieve this we synthesized bottle brush type copolymers consisting of poly(ethylene glycol) methyl ether methacrylate and (meth)acrylates providing activated NHS ester groups as well as different spacer lengths between the NHS groups and the polymer backbone. Copolymers containing different molar ratios of these monomers were grafted to amine functionalized polystyrene cell culture substrates, followed by the covalent immobilization of the cyclic peptides cRGDfK and cRADfK using residual NHS groups. Polymers were characterized by GPC and NMR and surface modification steps were analyzed using XPS. The cellular response was evaluated using HeLa cell attachment experiments. The results showed strong correlations between the effectiveness of the control over biointerfacial interactions and the polymer architecture. They also demonstrate that optimized fully synthetic copolymer coatings, which can be applied to a wide range of substrate materials, provide excellent control over biointerfacial interactions., (Copyright © 2011 Wiley Periodicals, Inc.)

DNA, protein and cell microarrays are increasingly used in a multitude of bioassays. All of these arrays require substrates that are suitable for the immobilisation and display of arrayed probe molecules whilst at the same time resisting non-specific interactions of biomolecules with the substrate in areas between printed spots. To meet these conflicting requirements, three different approaches have been developed, all of which were based on low-fouling, high-density poly(ethylene glycol) (PEG) background coatings. In the first approach, the coating was based on allylamine plasma polymerisation (ALAPP) and the subsequent high-density grafting of PEG, followed by the generation of a surface chemical pattern using laser ablation. In the second approach, a photoreactive polymer was printed on the same ALAPP-PEG background. The third approach was based on ALAPP deposition followed by the formation of a multifunctional layer by spin coating a PEG-based polymer that also displayed epoxy groups. The successful demonstration of DNA, protein and cell microarrays has been achieved on each of these coatings.

Polymer microarrays provide a high-throughput format in which to assess biointerfacial interactions. This endeavor greatly assists with the development of advanced biomaterials. In order to increase the scope of this platform technology, the development of analytical tools that are compatible with the microarray format and are capable of analyzing biomolecular interactions in high throughput is needed. Here, we show that surface plasmon resonance imaging (SPRi) is such a tool. SPRi enables spatially resolved, surface sensitive, label free, real-time analysis of multiple surface-biomolecular interactions in parallel. In order to demonstrate this, we first printed phenylazide-modified polymers onto a slide coated with a low fouling base polymer. UV irradiation of the slide resulted in the cross-linking of the printed polymer spots to the surface. SPRi was then employed to study the adsorption and desorption of bovine serum albumin, collagen, and fibronectin to these adhesive microarray spots. The spots were also incubated with an adherent cell line, enabling insight into the underlying mechanisms of cell attachment to the polymers studied. For the system analyzed here, electrostatic interactions were shown to dominate cell attachment.

Stimuli-responsive materials show considerable promise for applications that require control over biomolecule interactions at solid material interfaces. Graft coatings of poly(N-isopropylacrylamide) (pNIPAM) are of interest for biomedical and biotechnological applications due to their temperature-dependent switching of surface properties between adhesive and nonadhesive states for cells and proteins. The characterization of protein adsorption to these switchable coatings is a formidable task since switching not only influences the affinity for proteins but at the same time induces a significant change in the coating. Here, the highly sensitive analytical technique of time-of-flight-secondary ion mass spectrometry (TOF-SIMS) combined with principal component analysis (PCA) was used for the characterization of protein adsorption onto pNIPAM coatings prepared by free radical polymerization onto surface-bound polymerizable groups. Adsorption of bovine serum albumin and lysozyme onto pNIPAM coatings from phosphate buffered solutions was investigated at temperatures above and below the polymer's lower critical solution temperature (LCST). Below the LCST, no adsorbed proteins could be detected even with this ultrasensitive method. Whereas above the LCST, adsorbed protein was detected in amounts corresponding at less than the monolayer. PCA loadings plots showed that adventitious contaminants, which might lead to confounding or misleading spectral changes upon protein exposure, were not observed.

Articular cartilage tissue engineering procedures require the transplantation of chondrocytes that have been expanded in vitro. The expansion is carried out for a considerable time and can lead to a modulation of cell phenotype. However, microcarrier cultures have been shown to allow cell expansion while maintaining the phenotype. Here, we have used the biodegradable polyester poly(lactide-co-glycolide) (PLGA) in the form of microspheres and irregular shaped microparticles with a diameter between 47 and 210 microm. Surface modification of particles was carried out by ammonia plasma treatment and subsequent adsorption of collagen. Alternatively, particles were modified by partial hydrolysis and subsequent immobilization of an amine-terminated dendrimer. Each surface modification step was characterized by X-ray photoelectron spectroscopy. The effectiveness of the surface modification procedures was demonstrated by in vitro cell culture experiments using sheep articular cartilage chondrocytes. A significant influence of both the particle shape and the surface chemistry on the proliferation rate was observed while the phenotype was maintained independent of the surface chemistry or particle shape. Chondrocytes cultured on PLGA microspheres were further assessed for cartilage tissue formation in collagen type I gels in nude mice. The tissue that were formed showed the appearance of a hyaline-like cartilage and the presence of the microspheres substantially reduced the degree of collagen gel contraction over 1-2 months.

The aim of the present study was to develop a short bioresorbable ureteric stent and to characterize the chosen polymers with respect to surface modification, biocompatibility, and loading of a biologically active compound. As materials for the stent, poly(D,L-lactide) and poly(D,L-lactide-co-glycolide) were chosen. Degradation experiments were carried out and analytical data were obtained by contact angle measurement, X-ray photoelectron spectroscopy (XPS), and infrared spectroscopy in the attenuated reflection mode (FTIR-ATR). Gas loading technology was used to incorporate biologically active compounds, and biocompatibility of the polymers was assessed by in vitro cellular assays, applying measures such as cell morphology, proliferative activity, and membrane integrity. Our results indicate that surface modification of bioresorbable polymers is a suitable and efficient approach to improve the surface properties. Incorporation of biologically active compounds was possible without loss of activity, and in vitro assessment of cellular responses demonstrated the biocompatibility of the chosen polymers and modifications.

Abstract: The effects of a radiofrequency oxygen plasma pretreatment and residual water content in the substrate on the adhesion of microwave plasma deposited tetramethyldisiloxane thin films on Bisphenol-A polycarbonate (BPA-PC) were investigated. Samples were characterised using a crosshatch adhesion test, optical and electron microscopy, and X-ray photoelectron spectroscopy. It was found that the use of a low power (5 W) and low treatment time (0.1 s) oxygen plasma can improve adhesion while greater treatment times (1–30 s) and higher oxygen plasma powers (40 W) resulted in a decreased level of adhesion. In addition, it was shown that a BPA-PC water content greater than 90 ppm resulted in rapid adhesion failure of deposited films at the substrate–plasma polymer interface during outdoor weathering. All films degraded substantially when exposed to environmental weathering, indicating ageing reactions within the plasma polymer films themselves, and at the bulk polymer–coating interface. [Copyright &y& Elsevier]

The use of graft polymers for the functionalisation of biomaterial surfaces is already widespread. We investigated the adsorptive and covalent binding of a variety of proteins and peptides to poly(d,l-lactide) grafted with polyacrylic acid. Covalent attachment was achieved through coupling of amino groups of the protein/peptide to the carboxyl groups of the graft polymer by using a water-soluble carbodiimide and N-hydroxysuccinimide. Binding densities were determined by automated amino acid analysis after acid hydrolysis of both the poly(d,l-lactide) and the adsorbed and covalently bound proteins. Experiments in the absence and presence of the coupling reagents allow to discriminate between adsorptive and covalent binding. Although the adsorptive binding is quite substantial in absolute terms, the amount of adsorbed protein is relatively low as compared to the total amount of bound protein.Total binding densities of 20–30 μg/cm2 can easily be achieved. Depending on the concentration and on the properties of the proteins and peptides, between 5% and 80% of the totally bound protein may be physically adsorbed.Densities expressed in molecules/10 nm2 vary from 0.5 molecule fibronectin to 2000 laminin-peptide molecules: their binding densities clearly correlate with their respective molecular masses. Obviously, the binding densities are governed by their individual three-dimensional space requirements rather than the density of the available carboxyl groups.From the number of carboxyl groups/10 nm2 (18,000–30,000 COOH/10 nm2) the average length of the acrylic acid graft polymer molecules was estimated. Based on the assumption that about 10 copolymer chains can be accommodated on 10 nm2, the average length of the polymer chains, which corresponds to the thickness of the graft phase, is estimated to be 0.5–1 μm.The organisation of the proteins and peptides within the polyacrylic acid phase was further investigated by experiments in which a protein (BSA) and a peptide (Val-Lys) were allowed to react in either a singular, a consecutive or a simultaneous way. Together with XPS and IR-ATR surface characterisation experiments a three-dimensional picture of the arrangement of the immobilised proteins and peptides within the graft polymer phase emerges. [Copyright &y& Elsevier]