Search

The contribution deals with the basic principles of operation of EDR technology and the further process of obtaining and using data for the reconstruction of an accident. One of the many devices that leave a digital evidence is the EDR memory module, which is contained in the airbag control unit of a car and which can record and store data from the accident. The CDR system enables to download and decode the stored data from the airbag control module, that experts can use among others for the technical analysis of an accident and objectively reconstruct it. The future of the analysis of traffic accidents will lie in use of the CDR system and the correct evaluation of the technical data obtained from the memory of the airbag unit. Legislative and technical preparations, which are currently taking place in Europe, aim to establish clear rules and requirements for OEM companies to implement Event Data Recorder (EDR) all over. It shows what data should be stored in airbag unit, how long is the section and what frequency must be used for data acquisition. The aim of these preparations is to establish clear rules for passenger car manufacturers (category M1 and all vehicles complying with the requirements), which should enter into force in 2022.

Objective: Field data have shown significant benefit from driver airbag for occupant protection in frontal crashes. However, vehicle modifiers almost always permanently deactivate airbags for wheelchair-seated drivers. The objective of this study was to conduct sled tests and computational simulations to answer whether driver airbags should be deactivated for drivers seated in wheelchairs. Methods: Five sled tests were conducted under a 48-kph 20-g frontal crash pulse all with driver airbag. Seat-belt fit (good, poor, and unbelted), airbag deployment time (proper and late), and occupant size (midsize male and small female HIII ATDs) were varied in the tests. The 2006 Chrysler Town-and-Country minivan was selected as the nominal vehicle environment, and a surrogate wheelchair with a docking securement system was used for all sled tests. ATD injury measures for the head, neck, chest, and lower extremities were recorded in each test, and were used for validating a set of MADYMO models. Parametric studies with a total of 28 MADYMO simulations were then conducted to investigate the airbag effects on occupant injury risks with varied occupant size, belt fit, and impact angle (0, 15, and 30 deg). Results: The sled tests showed potential safety concerns for wheelchair-seated drivers with a poor belt fit or without a belt. Specifically, the unbelted midsize male ATD sustained high femur forces and the small female ATD with poor belt fit sustained high chest deflections. The parametric simulations showed that airbag generally improved the protection for wheelchair-seated drivers. It is especially useful for unbelted wheelchair-seated drivers, and is also helpful for reducing the head and neck injury risks regardless of the belt condition, occupant size, and impact angle. Conclusions: This is the first study using sled tests and computational simulations to investigate the effects of airbag deployment on injury risks of wheelchair-seated drivers. Overall, the results showed little basis for concern that the energy of deploying a driver airbag in today’s vehicles will cause serious-to-fatal injuries to drivers seated in wheelchairs. The results of this study therefore support the idea that driver airbags generally offer tangible safety benefits for a wide range of wheelchair-seated drivers in frontal crashes.

Activation time for activating the occupant restraint systems (airbag and seatbelt) is very critical for an optimal safety action. A crash-pulse is the deceleration of the vehicle measured during in a crash. The shape, slope, maximum deceleration and duration of the crash-pulse provides significant information over the nature of occupant motions during in-crash phase and hence the crash severity. The above parameters of the crash-pulse not only depend on the mass and impact velocity but also on the crash configuration (position of impact, overlap, relative approach angle etc.). This study focuses on analysis and characterization of crash-pulses in head-on collision cases with varying overlap configurations. The paper describes causes for occupant injuries during a crash, crash-pulse and its important physical parameters, and different methodologies used to analyse the crash-pulse. Finite element simulation method is used to study the crash-pulses from different crash configurations. A new severity index that has direct influence on the occupant kinematics is defined. The results show that the steep decrease of crash-pulse for small overlap configurations (less than 25 percent of vehicle width) lags by 20 to 25 milliseconds as compared to configurations with large overlaps. The shape of the crash-pulse also changes for crash scenarios with different overlap configurations. The results, discussion and conclusion sections of this paper provide a summary of crash behaviour of varying overlap crash scenarios and insights that can be used for deployment of restraint systems.

Cycling accidents are the leading cause of sports-related head injuries in the US. Conventional bicycle helmets typically consist of polycarbonate shell over Expanded Polystyrene (EPS) foam and are tested with drop tests to evaluate a helmet’s ability to reduce head kinematics. Within the last decade, novel helmet technologies have been proposed to mitigate brain injuries during bicycle accidents, which necessitates the evaluation of their effectiveness in impact testing as compared to conventional helmets. In this paper, we reviewed the literature to collect and analyze the kinematic data of drop test experiments carried out on helmets with different technologies. In order to provide a fair comparison across different types of tests, we clustered the datasets with respect to their normal impact velocities, impact angular momentum, and the type of neck apparatus. When we analyzed the data based on impact velocity and angular momentum clusters, we found that the bicycle helmets that used rotation damping based technology, namely MIPS, had significantly lower peak rotational acceleration (PRA) and Generalized Acceleration Model for Brain Injury Threshold (GAMBIT) as compared to the conventional EPS liner helmets (p < 0.01). SPIN helmets had a superior performance in PRA compared to conventional helmets (p < 0.05) in the impact angular momentum clustered group, but not in the impact-velocity clustered comparisons. We also analyzed other recently developed helmets that primarily use collapsible structures in their liners, such as WaveCel and Koroyd. In both of the impact velocity and angular momentum groups, helmets based on the WaveCel technology had significantly lower peak linear acceleration (PLA), PRA, and GAMBIT at low impact velocities as compared to the conventional helmets, respectively (p < 0.05). The protective gear with the airbag technology, namely Hövding, also performed significantly better compared to the conventional helmets in the analyzed kinematic-based injury metrics (p < 0.001), possibly due to its advantage in helmet size and stiffness. We also observed that the differences in the kinematic datasets strongly depend on the type of neck apparatus. Our findings highlight the importance and benefits of developing new technologies and impact testing standards for bicycle helmet designs for better prevention of traumatic brain injury (TBI).

A method to evaluate the effectiveness of wearable airbag protectors for motorcyclists is proposed in this work. The mitigation of thoracic injury severity in relevant accident conditions was inves...

PURPOSE Each year, many cars (in Poland approximately three hundred) are adopted for disabled driver, to enable them to drive the car independently. The purpose of the paper is to assess the key factors which significantly influence the disabled driver behavior during a frontal crash and have the biggest impact on the safety factors. METHODS To achieve the purpose of the paper, the finite element method was used. The authors built the numerical model which includes operation of all safety systems operating in the real car (sensors, seat belts, airbag). Using this method, the authors simulated few different cases of the frontal crash of the car driven by a person with disabilities. RESULTS The obtained results were: displacements, velocities and accelerations of the head, pelvis and shoulders. Additional results were also loads in the neck. Based on the achieved results, several biomechanical parameters and criterions (HIC, Nij) were computed. CONCLUSIONS Therefore, during car adaptation for disabled drivers using a four-point seat belts system, this parameter can be optimized to reduce forces acting on the driver chest. Higher values of the force limit reduce Nij and increase HIC and contact forces between the dummy and seatbelts. Therefore, during designing of the pyrotechnic four-point seat belts system, the pretensioner characteristics should be analyzed taking all the driver's biomechanical parameters into account.

Objective Advanced occupant protection systems in motor-vehicles (e.g., seat belts and airbags), while widely adopted for front-seat passengers, are either absent or offer disproportionally lower safety to rear-seat passengers in similar crashes. Optimization of advanced restraint systems for the rear-seat environment will require a detailed understanding of epidemiology and associated risk factors for injuries sustained by rear-seat passengers. Thus, the objective of the study is to use national level motor-vehicle travel and crash data to quantify rear-seat travel exposure, and determine the descriptive characteristics and the injury outcomes for rear-seat passengers involved in frontal collisions. Methods While U.S. travel data from the 2009 National Household Travel Survey was used to determine rear-seat travel estimates, crash data from 2001 to 2010 National Automotive Sampling System Crash Worthiness Data System was used to enroll rear-seat passengers injured in a frontal crash. The descriptive epidemiology of rear-seat crash victims was separately done for the three age-groups: children (8–15 years old), adults (16–59 years old), and senior adults (60+). Results The study indicated that senior adults in rear-seats were associated with a significantly higher rate of sustaining fatal (6%) and severe injuries (16% for MAIS 3+ injuries) in comparison to the younger cohorts. The distribution of severe injuries further indicated that the thorax was the most frequently injured region across all age groups irrespective of the belt-use status. Conclusions Findings of the study conclude that while rear-seat travel in the U.S. is still very low and improving belt usage is a primary concern among rear-seat passengers; however, the epidemiology supports the need for adapting rear-seat restraint performance for effective protection for all groups of rear-seat passengers.

Our goal was the development of a robust and data-driven approach to ISO 26262 injury severity (S-parameter) estimation, replacing the current heuristic methods. The situations investigated as part of an ISO 26262 hazard & risk analysis are broken down into crash configurations. These crashes are analyzed from the perspective of the ADAS-equipped vehicle with the failing system as well as from the crash opponent's point of view. Mainly due to sample size limitations, we focus on belted front-row vehicle occupants. We cluster the crash data into traffic domains (TD) based on the speed limit, i.e., residential streets, city roads, arterial thoroughfares, rural roads, and intercity highways and calculate the crash speed distribution for each domain. The injury severity clustering is based on the ISS injury aggregator with cut-offs at 4, 9, and 16 for S1, S2, and S3, respectively. We estimated the 90th-percentiles of the S-parameter cut-offs with a 95% confidence level using the GIDAS accident database. The percentiles were calculated for the ADAS-equipped vehicle as well as for the crash opponent, stratified for crash type (front, oblique, side). The stratification had to be detailed further for side crashes as impact direction (near-side vs. far-side) and availability of a curtain airbag restraint system have a significant impact on injury severity. The application of the results towards the assessment of a crossing scenario is detailed in the discussion.

The current practice of crash characterization in highway engineering reduces multiple dimensions of crash contributing factors and their relative sequential connections, crash sequences, into broad definitions, resulting in crash categories such as head-on, sideswipe, rear-end, angle, and fixed-object. As a result, crashes that are classified in the same category may contain many different crash sequences. This makes it difficult to develop effective countermeasures because these crash categorizations are based on the outcomes rather than the preceding events. Consequently, the efficacy of a countermeasure designed for a specific type of crash may not be appropriate due to different pre-crash sequences. This research seeks to explore the use of event sequence to characterize crashes. Additionally, this research seeks to identify crash sequences that are likely to result in severe crash outcomes so that researchers can develop effective countermeasures to reduce severe crashes. This study utilizes the sequence of events from roadway departure crashes in the Fatality Analysis Reporting System (FARS), and converts the information to form a new categorization called "crash sequences." The similarity distance between each pair of crash sequences were calculated using the Optimal Matching approach. Cluster analysis was applied to group crash sequences that are etiologically similar in terms of the similarity distance. A hybrid model was constructed to mitigate the potential sample selection bias of FARS data, which is biased toward more severe crashes. The major findings include: (1) in terms of a roadway departure crash, the crash sequences that are most likely to result in high crash severity include a vehicle that first crosses the median or centerline, runs-off-road on the left, and then collides with a roadside fixed-object; (2) seat-belt and airbag usage reduces the probability of dying in a roadway departure crash by 90%; and (3) occupants who are seated on the side of the vehicle that experience a direct impact are 2.6 times more likely to die in a roadway departure crash than those not seated on the same side of the vehicle where the impact occurs.

Bicycling is the leading cause of sports-related traumatic brain injury. Most of the current bike helmets are made of expanded polystyrene (EPS) foam and ultimately designed to prevent blunt trauma, e.g., skull fracture. However, these helmets have limited effectiveness in preventing brain injuries. With the availability of high-rate micro-electrical-mechanical systems sensors and high energy density batteries, a new class of helmets, i.e., expandable helmets, can sense an impending collision and expand to protect the head. By allowing softer liner medium and larger helmet sizes, this novel approach in helmet design provides the opportunity to achieve much lower acceleration levels during collision and may reduce the risk of brain injury. In this study, we first develop theoretical frameworks to investigate impact dynamics of current EPS helmets and airbag helmets-as a form of expandable helmet design. We compared our theoretical models with anthropomorphic test dummy drop test experiments. Peak accelerations obtained from these experiments with airbag helmets achieve up to an 8-fold reduction in the risk of concussion compared to standard EPS helmets. Furthermore, we construct an optimization framework for airbag helmets to minimize concussion and severe head injury risks at different impact velocities, while avoiding excessive deformation and bottoming-out. An optimized airbag helmet with 0.12 m thickness at 72 ± 8 kPa reduces the head injury criterion (HIC) value to 190 ± 25 at 6.2 m/s head impact velocity compared to a HIC of 1300 with a standard EPS helmet. Based on a correlation with previously reported HIC values in the literature, this airbag helmet design substantially reduces the risks of severe head injury up to 9 m/s.

Motor vehicle passenger airbags have been proven to be effective for reducing the possibility of passenger injury during a crash. However, the inflation of the airbag sometimes causes serious injury when a passenger is positioned close to the airbag. The United States Federal Motor Vehicle Safety Standard (FMVSS) 208 requires the use of a low-riskdeployment (LRD) passenger airbag system. This paper proposes a newly developed airbag system comprising two slim airbags mounted on the instrument panel. A series of tests were conducted using the FMVSS 208 test procedures to demonstrate the effectiveness of the proposed system. It was found that the system not only satisfied the injury criteria of FMVSS 208, but was also effective for protecting passengers of all sizes.

Computational modelling is an effective way of estimating the risk of injuries and fatalities in road traffic accidents. Computational pregnant occupant modelling has an additional important role in the investigation of the risk of fetus mortality in crash test simulations. In this paper, the effect of including the fetus in the uterus of the pregnant occupant model is investigated. First, isolated drop test simulations with the uterus of the computational pregnant occupant model, ‘Expecting’, with and without a fetus are used to show the effect of the presence of fetus in the uterus model. Then ‘Expecting’ with and without the fetus is used with varying levels of restraint system use, such as fully restrained, ‘seatbelt only’, ‘airbag only’ and ‘no restraint’, in frontal crash simulations, representing five levels of impacts. Maximum strains developed in the uteroplacental interface with and without a fetus are compared in every case. Both simulations predict higher risks of placental abruption w...

Neurogenic thoracic outlet syndrome (NTOS) is a disorder that is often misdiagnosed and challenging to treat due to the varied and complex mechanisms that precipitate common sensory symptoms associated with neurovascular dysfunction. In this report, we describe a 21-year-old male who presented with left NTOS after being involved in a motor vehicle collision the previous year. Although NTOS is a condition known to develop after motor vehicle collisions, the mechanism of NTOS in this case, the deploying airbag, has not been documented in existing literature. The patient was first treated conservatively with physical therapy, but treatment failed to relieve his symptoms. A left first rib resection using the transaxillary approach and an anterior scalenectomy was performed without any complications, and the patient's symptoms had improved 3 months postoperation.

In autonomous vehicles, passengers often recline their seatbacks for a more comfortable posture. Such a reclined posture greatly increases risk of submarining and other injury concerns due to the unfavourable geometrical configuration of occupant, seat and seatbelt. In this paper, numerous simulations with a modified computational dummy model are proposed to analyse effects of various occupant restraint systems in frontal impact, including seatbelt, pretensioner, load limiter, locking tongue, airbag, knee bolster and so on. After the sensitivity analyses, four concepts for designing anti-submarining countermeasures are proposed: (1) increase the lap belt-to-pelvis friction coefficient; (2) reduce the shoulder belt force along with the use of the locking tongue; (3) increase the lap belt angle; (4) reduce the H point forward and downward displacement. Sled tests with anti-submarining countermeasures were conducted to verify the effectiveness of the anti-submarining concepts for reclining seats. Four anti-submarining countermeasures are suggested to prevent the submarining with no other auxiliary hurts: load limiter plus locking tongue, anchor pretensioners plus anti-submarining bar, seat cushion airbag, and retractor plus buckle pretensioner. This paper could give better understanding of submarining mechanism and eligible vehicle design.

Accident emergency calling systems (AECSs) are signaled by the deployment of airbags, which causes them to automatically emit information providing the location of the accident site to a public service answering party (PSAP). In some realworld accidents, airbags have failed to deploy. This study clarifies the factors that influence the nondeployment of front airbags in vehicle-vehicle collisions, investigating nondeployment of the driver-side front airbags in sedans and light passenger cars (LPCs) from Japanese accident data. The component rates of deployment for front airbags tend to be higher than those of nondeployment at higher values of pseudo-ΔV in vehicle-vehicle frontal impacts. For both sedans and LPCs, the transition zones between nondeployment and deployment of the front airbag occur at pseudo-ΔV values of 30-50 km/h (ΔV ≈ 21-35 km/h). For mutual impact locations where sedans and LPCs impact opponent vehicles at pseudo-ΔV ≥ 40 km/h (ΔV ≈ 28 km/h) in frontal impacts, the component rate of front airbag nondeployment is higher than that of deployment in right-to-right impacts. The results indicate that factors influencing front airbag nondeployment in vehicle-vehicle collisions are ΔV, impact offset configuration, and crossing angle. Considering front airbag nondeployment in real-world accidents, AECSs should have other functions, such as a manual button, to emit information in addition to automatic emission via airbag signaling.

Motorcycle accidents lead to a high rate of traffic mortality and morbidity. While helmet development and mandatory wearing have reduced head injuries, little progress has been made regarding trunk protection. Wearable airbag devices represent a promising solution to prevent trunk injuries. Nevertheless, research investigations need to be performed to assess and optimise the efficiency of such devices. This work consisted in the analysis of motorcyclist trunk impact conditions involved in various crash configurations to provide critical information in order to evaluate and improve the performances of airbag devices. First, an epidemiological and an accidentological analysis of data collection related to 252 real accidents, focusing on victims admitted into the shock rooms of two French trauma centres were performed. The data obtained was combined with numerical multibody parametric investigations, allowing the reproduction of 240 accident situations. An original and representative analysis of motorcyclists' impact conditions was provided, weighting the numerical study output data according to the real accident database. The impacted regions of the human body, the impact velocity and the accident chronology obtained in this work made it possible to define critical information for airbag efficiency assessment: the zones and levels of protection, the impacted surfaces as well as the airbag intervention time and the duration of maintained inflation of the airbag.

Temporal variation has been recognized as one of the major sources of unobserved heterogeneity in traffic safety research that has not been completely addressed. Overlooking temporal variation may result to biased estimates of effects of impact factors. This paper develops a latent class mixed logit model with temporal indicators to investigate highway single-vehicle crashes and the effects of significant contributing factors to driver injury severity. Crash data from 2010 to 2016 in Washington State is collected with a total of 31,115 single-vehicle crashes. The developed model is able to interpret both within- and across- class unobserved heterogeneity and temporal variation. After a careful comparison, a two-class model is selected as the final model. Estimation results show that: two temporal indicators show significant influence on latent class probability functions; urban indicator and principle type are found to be random parameters and have significant heterogeneity in the mean as a function of male indicator and driver’s age indicators. Variables with fixed effects, including animal collision, overturn collision, off-road collision, winter, minor arterial, interstate, wet, snow, ice, speed limit, vehicle age, turning movement, out control movement, lane-change movement, no airbag, deployed airbag, partial and total ejection, seatbelt, and no liability, show significant impacts on different levels of injury severity outcomes in each class. This study provided an insightful understanding of the time-varying effects of the significant factors on driver injury severity using marginal effect analysis, and the temporal indicators in the proposed model were found to enhance the model capability of temporal variation identification.

Recent field data analysis has demonstrated that knee airbags (KABs) can reduce occupant femur and pelvis injuries but may be insufficient to decrease leg injuries in motor vehicle crashes. An enhanced understanding of the associated injury mechanisms requires accurate assessment of physiological-based occupant parameters, some of which are difficult or impossible to obtain from experiments. This study sought to explore how active muscle response can influence the injury risk of lower extremities during KAB deployment using computational biomechanical analysis.A full-factorial matrix, consisting of 48 finite element simulations of a 50th percentile occupant human model in a simplified vehicle interior, was designed. The matrix included 32 new cases in combination with 16 previously reported cases. The following influencing factors were taken into account: muscle activation, KAB use, KAB design, pre-impact seating position, and crash mode. Responses of 32 lower extremity muscles during emergency braking were replicated using one-dimensional elements of a Hill-type constitutive model, with the activation level determined from inverse dynamics and validated by existing volunteer tests. Dynamics of unfolding and inflating of the KABs were represented using the state-of-the-art corpuscular particle method. Abbreviated Injury Scale (AIS) 2+ injury risks of the knee-thigh-hip (KTH) complex and the tibia were assessed using axial force and resultant bending moments. With all simulation cases being taken together, a general linear model was used to assess factor significance (P.05).As estimated by the regression model across all simulation cases, use of KABs significantly reduced axial femur forces by 4.74 ± 0.43 kN and AIS 2+ injury risk of KTH by 47 ± 6% (P.05) but did not provide substantial change to injury risk of leg fractures. Muscle activation significantly increased axial force and bending moment of the femur (3.87 ± 0.38 kN and 64.3 ± 5.9 Nm), the tibia (1.49 ± 0.12 kN and 43.0 ± 6.4 Nm), and the resultant probability of AIS 2+ tibia injuries by 36 ± 6% regardless of KAB use and crash scenario. Specifically, when counting on a relative scale, muscle activation exhibited more prominent elevation of injury risk for in-position occupants than out-of-position occupants. In a representative crash scenario-that is, using a bottom-deployed KAB in a nearside oblique impact-muscle bracing of the right leg may lead to 2.6 times higher tibia fracture risk than being relaxed for an out-of-position occupant and 5.4 times higher for an in-position occupant.The mechanism of higher leg injuries in the presence of KAB deployment in real-world crashes can be interpreted by the increased effective body mass, axial compression along the shafts of long bones, and altered pre-impact posture due to muscle contraction. The present analysis suggests that active muscle response can increase the risk of lower extremity injury during occupant-KAB interaction. This study demonstrated the feasibility of advanced human models to investigate the influence of physiologically based parameters on injury outcomes evidenced in field study and insight from computational examination on human variability for development of future restraint systems. Future efforts are recommended on realistic vehicle and restraint environment and advanced modeling strategies toward a full understanding of KAB efficacy.

The purpose of this study was to use the detailed medical injury information in the Crash Injury Research and Engineering Network (CIREN) to evaluate patterns of rib fractures in real-world crash occupants in both belted and unbelted restraint conditions. Fracture patterns binned into rib regional levels were examined to determine normative trends associated with belt use and other possible contributing factors.Front row adult occupants with Abbreviated Injury Scale (AIS) 3+ rib fractures, in frontal crashes with a deployed frontal airbag, were selected from the CIREN database. The circumferential location of each rib fracture (with respect to the sternum) was documented using a previously published method (Ritchie et al. 2006) and digital computed tomography scans. Fracture patterns for different crash and occupant parameters (restraint use, involved physical component, occupant kinematics, crash principal direction of force, and occupant age) were compared qualitatively and quantitatively.There were 158 belted and 44 unbelted occupants included in this study. For belted occupants, fractures were mainly located near the path of the shoulder belt, with the majority of fractures occurring on the inboard (with respect to the vehicle) side of the thorax. For unbelted occupants, fractures were approximately symmetric and distributed across both sides of the thorax. There were negligible differences in fracture patterns between occupants with frontal (0°) and near side (330° to 350° for drivers; 10° to 30° for passengers) crash principal directions of force but substantial differences between groups when occupant kinematics (and contacts within the vehicle) were considered. Age also affected fracture pattern, with fractures tending to occur more anteriorly in older occupants and more laterally in younger occupants (both belted and unbelted).Results of this study confirmed with real-world data that rib fracture patterns in unbelted occupants were more distributed and symmetric across the thorax compared to belted occupants in crashes with a deployed frontal airbag. Other factors, such as occupant kinematics and occupant age, also produced differing patterns of fractures. Normative data on rib fracture patterns in real-world occupants can contribute to understanding injury mechanisms and the role of different causation factors, which can ultimately help prevent fractures and improve vehicle safety.

Background The risk of serious injury or death has been found to be reduced for some front compared to rear seat car passengers in newer vehicles. However, differences in injury severity between car occupants by seating position has not been examined. This study examines the injury severity risk for rear compared to front seat car passengers. Method A retrospective matched-cohort analysis was conducted of vehicle crashes involving injured rear vs front seat car passengers identified in linked police-reported, hospitalisation and emergency department (ED) presentation records during 2001–2011 in New South Wales (NSW), Australia. Odds ratios were estimated using an ordinal logistic mixed model and logistic mixed models. Results There were 5419 front and 4588 rear seat passengers in 3681 vehicles. There was a higher odds of sustaining a higher injury severity as a rear-compared to a front seat car passenger, with a higher odds of rear seat passengers sustaining serious injuries compared to minimal injuries. Where the vehicle occupant was older, travelling in a vehicle manufactured between 1990 and 1996 or after 1997, where the airbag deployed, and where the vehicle was driven where the speed limit was ≥70 km/h there was a higher odds of the rear passenger sustaining a higher injury severity then a front seated occupant. Conclusion Rear seat car passengers are sustaining injuries of a higher severity compared to front seat passengers travelling in the same vehicle, as well as when travelling in newer vehicles and where the front seat occupant is shielded by an airbag deployed in the crash. Rear seat occupant protective mechanisms should be examined. Pre-hospital trauma management policies could influence whether an individual is transported to a hospital ED, thus it would be beneficial to have an objective measure of injury severity routinely available in ED records. Further examination of injury severity between rear and front seat passengers is warranted to examine less severe non-fatal injuries by car seating position and vehicle intrusion.

The recent implementation of new federal regulations on injury criteria for occupants in side-facing seats greatly decreases the risk for these passengers. One of these new requirements limits the amount of leg flail allowed to the occupant. While the limit of rotation is defined at 35°, the method of measurement of this angle is left open to the end user. Photometric analysis and angular rate sensor data are analysed and evaluated, first, on a pendulum fixture to determine any difference between the two and then, second, on an ES-2re anthropomorphic test device (ATD) in a side-facing seat. The leg flail or leg rotation is measured in three different configurations: an unrestrained leg, a rigid block to restrain the leg, and with an airbag deployed to restrain the leg. Various targets are tracked from the high-speed video, and the photometric results for each are compared to the angular rate sensor data during the impact test.

In minicars, the survival space between the side structure and occupant is smaller than in conventional cars. This is an issue in side collisions. Therefore, in this article a solution is studied in which a lateral seat movement is imposed in the precrash phase. It generates a pre-acceleration and an initial velocity of the occupant, thus reducing the loads due to the side impact.The assessment of the potential is done by numerical simulations and a full-vehicle crash test. The optimal parameters of the restraint system including the precrash movement, time-to-fire of head and side airbag, etc., are found using metamodel-based optimization methods by minimizing occupant loads according to European New Car Assessment Programme (Euro NCAP).The metamodel-based optimization approach is able to tune the restraint system parameters. The numerical simulations show a significant averaged reduction of 22.3% in occupant loads.The results show that the lateral precrash occupant movement offers better occupant protection in side collisions.

We report the case of an 8-month-old baby killed by the deployment of an airbag. He was correctly positioned, in a safety seat designed for his age class, on the passenger side, and rear-facing. The accident occurred at low speed, on the left front of the car, without provoking any harm to the mother who was driving the vehicle, but the impact led to airbag deployment. A CT scan showed an occipital fracture, hemorrhagic parenchymal contusions, subarachnoid hemorrhage and edema, which quickly led to fatal intracranial hypertension. Severe retinal hemorrhages were also noted. Brain death was declared 24h later. Both direct impact and violent projection of the head are involved in the severity of brain lesions. Retinal hemorrhages are similar to what is observed in shaken-baby syndrome. To our knowledge, this is the first French publication on this topic in childhood. In France, children are allowed to be positioned on the passenger side seat, but the airbag, if present, is supposed to be deactivated, which is not always possible. In recent cars, depowering the airbag is easy, with on/off switches, but these systems are not uniform between models. Moreover, it is very likely that this possibility is ignored by numerous parents. A widespread communication on this topic should be initiated in France to prevent such events. Banning infants from front passenger seats completely does not seem possible. Nevertheless, greater attention on the part of police departments and better information to drivers appear necessary. Language: fr

Seatbelt restraints are important for occupant safety which substantially reduces morbidity and mortality in severe motor vehicle crashes (MVC). Though, it has been established that the air bag and seatbelt use reduce injury severity and mortality but still there is limited information on the pattern of injury by restraint type. Herein, we presented two case reports which describe the injury pattern of two patients (both were restrained but only driver had airbag) involved in a single MVC. Both of them had severe traumatic injuries, however, the restrained passenger without airbag, sustained more severe injuries of intestine, kidney and spinal cord. In addition to seatbelt, airbag provides considerable protection against severe blunt abdominal trauma. Therefore, installation of airbags especially for front seat passenger is imperative for minimizing the risk of significant traumatic injuries.

Thoracic side airbags (tSABs) deploy within close proximity to the occupant. Their primary purpose is to provide a protective cushion between the occupant and the intruding door. To date, various field studies investigating their injury mitigation has been limited and contradicting. The research develops efficacy estimations associated for seat-mounted tSABs in their ability to mitigate injury risk from the German collision environment.A matched cohort study using German In-Depth Accident Study (GIDAS) data was implemented and aims to investigate the efficacy of seat-mounted tSAB units in preventing thoracic injury. Inclusion in the study required a nearside occupant involved in a lateral collision where the target vehicle exhibited a design year succeeding 1990. Collisions whereby a tSAB deployed were matched on a 1:n basis to collisions of similar severity where no airbag was available in the target vehicle. The outcome of interest was an incurred bodily or thoracic regional injury. Through conditional logistic regression, an estimated efficacy value for the deployed tSAB was determined.A total of 255 collisions with the deployed tSAB matched with 414 collisions where no tSAB was present. For the given sample, results indicated that the deployed tSAB was not able to provide an unequivocal benefit to the occupant thoracic region, because individuals exposed to the deployed tSAB were at equal risk of injury (Thorax Maximum Abbreviated Injury Scale (Tho.MAIS)2+ odds ratio [OR] = 1.04, 95% confidence interval [CI], 0.41-2.62; Tho.MAIS3+ OR = 1.15, 95% CI, 0.41-3.18). When attempting to isolate an effect for skeletal injuries, a similar result was obtained. Yet, when the tSAB was coupled with a head curtain airbag, a protective effect became apparent, most noticeable for head/face/neck (HFN) injuries (OR = 0.59, 95% CI, 0.21-1.65).The reduction in occupant HFN injury risk associated with the coupled tSAB and curtain airbag may be attributable to its ability to provide coverage over previous mechanisms of injury. Yet, the sole presence of the tSAB showed no ability to provide additional benefit for the occupant's thoracic region. Future work should identify mechanisms of injury in tSAB cases and attempt to quantify improvements in the vehicle's ability to resist intrusion.

BACKGROUND: The combination of airbag and seat belt is considered to be the most effective vehicle safety system. However, despite the widespread availability of airbags and a belt use rate of more than 85%, US drivers involved in crashes continue to be at risk of serious thoracic injury. The objective of this study was to determine the influence of steering wheel deformation on driver injury risk in frontal automobile crash. METHODS: The analysis is based on cases extracted from the National Automotive Sampling System Crashworthiness Data System database for case years 1993 to 2011. The approach was to compare the adjusted odds of frontal crash injury experienced by drivers in vehicles with and without steering wheel deformation. RESULTS: Among frontal crash cases with belted drivers, observable steering wheel deformation occurred in less than 4% of all cases but accounted for 30% of belted drivers with serious (Abbreviated Injury Scale [AIS] score, 3+) thoracic injuries. Similarly, steering wheel deformation occurred in approximately 13% of unbelted drivers but accounted for 60% of unbelted drivers with serious thoracic injuries. Belted drivers in frontal crashes with steering wheel deformation were found to have two times greater odds of serious thoracic injury. Unbelted drivers were found to have four times greater odds of serious thoracic injury in crashes with steering wheel deformation. In frontal crashes, steering wheel deformation was more likely to occur in unbelted drivers than belted drivers, as well as higher severity crashes and with heavier drivers. CONCLUSION: The results of the present study show that airbag deployment and seat belt restraint do not completely eliminate the possibility of steering wheel contact. Even with the most advanced restraint systems, there remains an opportunity for further reduction in thoracic injury by continued enhancement to the seat belt and airbag systems. Furthermore, the results showed that steering wheel deformation is an indicator of potential serious thoracic injury and can be useful to prehospital personnel in improving the diagnosis of serious injuries. LEVEL OF EVIDENCE: Prognostic study, level III. Language: en

An active bonnet and pedestrian airbag are effective in providing a high level of pedestrian head protection. For triggering the activation of these systems, a reliable sensor that distinguishes a pedestrian collision from collisions against other colliding objects is necessary. In this research, a pedestrian contact sensor based on the pressure of a deformable chamber was investigated from finite-element (FE) analysis. In a simulation of a component test of a chamber impact, the internal pressure of the chamber increased with the volume deformation of the chamber according to Boyle's law. The chamber was installed above the top plane of the bumper energy absorber of a simple car model, and FE simulations of a car–pedestrian collision were conducted. The chamber deformed and its internal pressure increased as the bumper energy absorber deformed during contact with the pedestrian leg. It was shown that the pressure response of the chamber could be detected, irrespective of vehicle shape and structure. This...

The impact force to the head and neck were measured in sled tests with and without inflation of a combo airbag for a far-side occupant to determine the risk for basilar skull fracture.Sled tests were run at 24 and 32 km/h (15 and 20 mph) with and without inflation of a combo side airbag to analyze the effect of cross-car diving into the side interior. The matched tests involved one pair at 24 km/h and another at 32 km/h. The 24 km/h pair involved a lap-shoulder-belted 5th percentile female Hybrid III and the series at 32 km/h involved an unbelted 5th percentile Hybrid III. The dummy was ballasted to 69.5 kg (153 lb) and laid on the right side. The dummy was positioned 30.5 cm (12(″)) from the far-side interior to ensure the full sled delta V occurred before head impact. The buck consisted of a 2001 Ford Taurus. The combo thorax-head side airbag was stored in the seatback. The airbag was triggered about 120 ms before the head impact. The head, chest, and pelvis were instrumented with triaxial accelerometers and the upper and lower neck, thoracic spine, and lumbar spine had transducers measuring triaxial loads and moments. High-speed video recorded different views of the dummy motion. Dummy kinematics and biomechanical responses were compared to study the influence of inflating the side airbag on the head and neck.The top of the head impacted the far side. The force of impact was similar with and without the airbag as the head compressed the airbag and loaded the vehicle interior trim behind the airbag. The peak force on the head was primarily from neck load as torso augmentation occurred. For the 24 km/h (15 mph) tests, the peak force was 4.7 kN (1055 lb) without and 4.8 kN (1088 lb) with the airbag and there was over 2.67 kN (600 lb) of lap belt load. The peak head acceleration was 93 g without and 72 g with the airbag. For the 32 km/h (20 mph) tests, the force on the head was 15.3 kN (3433 lb) without and 15.2 kN (3406 lb) with the airbag, although the instrumentation saturated. The peak head acceleration was 236 g without and 262 g with the airbag.The airbag reduced head acceleration in the belted test but did not influence the diving forces from torso augmentation through the neck of the far-side occupant. The side airbag did not reduce the risk for basilar skull fracture due to high neck compression loads in either the belted or unbelted tests.

A healthy 40-year-old man, restrained in the front passenger seat, suffered visually disabling blunt ocular trauma following spontaneous release of the passenger side air-bag module, during vehicular deceleration, without an automobile crash. Though the driver-side airbag was also released, the driver was unharmed. The passenger suffered bilateral hyphema, bilateral vitreous hemorrhage and suspected posterior scleral rupture in the left eye and also had an eyebrow laceration, from impact with the dashboard panel covering the air-bag module, which was detached by the force of airbag deployment. This is the first reported case from West Africa and the first case in which part of the airbag module detached to cause additional trauma. This report adds to the growing burden of evidence world-wide, for a review of the safety aspects of the automobile airbag. This case clearly illustrates that although airbags reduce mortality, they carry a high risk of ocular morbidity, even with seat belt restraint.

Pedestrian safety is of keen interest because the vulnerability of pedestrians leads to severe injuries in pedestrian-vehicle crashes. Various countermeasures for protecting pedestrians have been developed in the field of traffic and vehicular safety engineering. The pedestrian protection airbag system (PPAS) is one of the recently developed vehicular technologies for pedestrian protection. PPAS is a promising, passive safety technology for reducing the severity of pedestrian injury. The purpose of this study was to evaluate the safety benefits of PPAS. A probabilistic pedestrian fatality model and a set of linear regression models were employed to estimate the effectiveness of PPAS in reducing the severity of pedestrian injury. Head injury criteria data, which represented the level of severity of pedestrian head injury, were obtained from indoor experimental collisions. The number of pedestrian fatalities was estimated for two cases on the basis of the pedestrian fatality model: one with PPAS and one wit...

The pattern of hand positioning varies considerably as drivers attempt to steer through sharp turns at low speed. The technique chosen by the driver should be the best compromise between car control and driver safety (i.e. airbag deployment). The purpose of this study was to assess different steering techniques in order to characterize the drivers steering profile, defined by tracking hand position. Authors propose a graphical method and a lateral indicator to define driver steering profiles. Tracking of hand steering position in twenty three volunteers with no upper arm disabilities was undertaken with a motion capture system. The steering exercise occurred in a simulator. Results from the hand tracking of steering indicate three distinct driver profiles of: hand-crossing (52%), non-hand-crossing (30%) and asymmetric-hand-crossing (17%). Most subjects steer with one hand and crossed hands often. This present a safety issue for the airbag deploying.

Passive safety has for many years reduced the number of fatalities on the roads. However, its effect on occupants' safety has now stabilised, meaning that new active safety features are needed to reduce further the number of casualties. These active safety features, like autonomous emergency braking (AEB), aim to prevent vehicle collisions and reduce the vehicle kinetic energy on impact. A previous study has shown that unbelted occupants kinematics are affected by the pre-braking phase, suggesting that the occupant's hand positions on the steering wheel, combined with a bracing behaviour, could cause the occupant to miss the deploying airbag in the case of a secondary rigid wall impact. This paper will investigate the variations of the secondary vehicle impact crash patterns by calculating crash pulses based on typical vehicle frontal accident scenarios and conclude on these effects on the human occupant's neck, head and thorax injuries.

Collision related data stored in the airbag control modules (ACM's) of Toyota vehicles can provide useful information to collision investigators, including both front and rear collision severity. Previous studies of ACM's from other manufacturers found that the devices underestimated the actual speed change in low speed frontal collisions. To quantify the accuracy and sensitivity of select 2005 to 2008 Toyota ACM's, in-vehicle crash tests and linear sled tests were performed in both front and rear impact orientations. A 2005 Toyota Corolla with five extra ACM's mounted in the right front seat position underwent a series of vehicle-to-barrier collisions with speed changes of up to 10 km/h. Next, the same six Toyota ACMs underwent a range of crash pulses using a linear sled. In all in-vehicle tests, the speed change reported by the ACM underestimated the actual speed change for frontal collisions, and overestimated the actual speed change for rear-end collisions. The speed change underestimates ranged from 1.3 to 2.6 km/h and the speed change overestimates ranged from 0.6 to 2.2 km/h. The magnitude of the error varied with collision duration and peak acceleration. Threshold accelerations required to initiate the recording of an event were found to be between 2.0 and 2.1g for all of the ACM's tested. A model using the threshold accelerations and a bias was generated to explain the speed change error. This study provides an understanding into the accuracy of the Toyota ACM reported speed change at low speeds and the collision parameters which can affect it. Language: en

Prior EDR testing methodologies required setting events in the airbag control module in the vehicle during controlled driving behavior. Duplicating events was nearly impossible, and it was difficult to separate how much differences in recorded speeds to reference speeds was due to measurement error, wheel slip, reporting time delays, or data truncation within the EDR. Recording thresholds have also increased making non-deployment and deployment events closer in magnitude, increasing the risk of accidentally exceeding the deployment threshold while setting events. The new methodology eliminates the risk of accidentally deploying airbags while gathering GPS and CAN bus data in the test vehicle. The techniques presented in this paper also allows gathering of data in vehicle without tampering with the airbag control module, which reduces the potential liability to testers using rental or borrowed test vehicles. The new methodology allows for repeatable testing and mapping the transfer function between the vehicle CAN bus data and the EDR. Should a manufacturer make a design change to an ACM EDR, identical inputs can be given to exemplar ACM's from before and after the changes to document any change in the transfer function. This methodology allows researchers the ability to re-create events of interest in a low-cost, repeatable manner. The accuracy of the 2012 Honda CR-V and 2012 Honda Civic event data recorders were tested using this new two part methodology. First, the test vehicles were instrumented with both a Racelogic VBOX differential GPS speed measurement system and a Vector CAN data logger. The measurements from the VBOX were transmitted onto the vehicle's Controller Area Network (CAN) bus that also contained messages reflecting indicated vehicle speed, brake status, accelerator pedal position, steering wheel angle, individual wheel speeds and other signals. This put the GPS speed data on the same time base as the vehicle CAN speed signal such that no additional synchronization was required. This permitted analysis of the accuracy and update rate of the vehicle speed CAN signal, which is the source for speed data used in the Event Data Recorder (EDR). Second, a system was developed to replay the recorded CAN data to an exemplar airbag control module in the laboratory, such that the exemplar was receiving data exactly as if it were in a moving vehicle. A pneumatic fixture with a slide was built to allow the exemplar module to be accelerated to nearly 10 km/h (6 mph) and then stopped in about 80 msec. to create a non-deployment event that met the minimum 5 mph delta-V over 150ms threshold. Actuation of the event setting fixture was computer controlled (using LabVIEW) and synchronized with the CAN replay system so that the desired test condition could be replicated precisely. An external accelerometer was mounted to the airbag control module to mark when the ACM began recording and the accelerometer data was matched to the acceleration and delta-V data in the EDR. The desired test conditions were replayed to the airbag control module and a series of non-deployment events were set. Each event on the EDR data was read using the Bosch Crash Data Retrieval system. The EDR data was compared to the inputs, and it was determined that the two byte vehicle CAN bus signal was truncated to the next lower whole km/h when recorded in the EDR. Under steady state conditions the speed data was accurate within 2%. The vehicle CAN signal published new values every 0.1 seconds, and the CR-V updated values every 0.1 seconds, but the Civic only updated every 0.6 seconds during hard brake events. During hard ABS braking events the expected wheel slip led to the vehicle speed signal under-reporting ground speed, but the delay in the CAN bus update rate resulted in over-reporting ground speed in many of the tests. Language: en

A new highly biofidelic side impact dummy, the WorldSID 50th percentile male, has been developed under the supervision of the International Organization for Standardization in order to harmonize a number of existing side impact dummies in one single dummy. Momentum is growing for using the WorldSID in safety tests in the EU and the US. In the present study, two Euro-NCAP pole side impact tests were conducted to compare ES-2 and WorldSID responses in a midsize SUV with respective seating positions as stipulated in the Euro-NCAP test conditions and fitted with the same side airbag. It was found that, compared with ES-2, the chest, abdomen and pelvis accelerations of WorldSID are more sensitive to variation in the applied external load transmitted by the deployed side airbag and door intrusion. Language: en

While belt usage among rear-seat passengers is disproportionately lower than their front-seat counterpart, this may have serious consequences in the event of a crash not only for the unbelted rear-seat passenger but also for the front-seat passengers as well. To quantify that effect, the objective of the study is to evaluate the increased likelihood of driver fatality in the presence of unrestrained rear-seat passengers in a severe frontal collision. U.S.-based census data from 2001 to 2009 fatal motor vehicle crashes was used to enroll frontal crashes which involved 1998 or later year vehicle models with belted drivers and at least one adult passenger in the rear left seat behind the driver. Results using multivariate logistic regression analysis indicated that the odds of a belt restrained driver sustaining a fatal injury was 137% (95% CI = 95%, 189%) higher when the passenger behind the driver was unbelted in comparison to a belted case while the effects of driver age, sex, speed limit, vehicle body type, airbag deployment and driver ejection were controlled in the model. The likelihood of driver fatality due to an unrestrained rear left passenger increased further (119–197%) in the presence of additional unrestrained rear seat passengers in the rear middle or right seats. The results from the study highlight the fact that future advances to front row passive safety systems (e.g. multi-stage airbag deployment) must be adapted to take into account the effect of unrestrained rear-seat passengers.

Fundamental physics and numerous field studies have shown a higher injury and fatality risk for occupants in smaller and lighter vehicles when struck by heavier, taller and higher vehicles. The consensus is that the significant parameters influencing compatibility in front-to-side crashes are geometric interaction, vehicle stiffness, and vehicle mass. The objective of this research is to develop a concept of deployable bumper and grille airbags for improved vehicle compatibility in side impact. The external airbags, deployed upon signals from sensors, may help mitigate the effect of weight, geometry and stiffness differences and reduce side intrusions. However, a highly reliable pre-crash sensing system is required to enable the reliable deployment, which is currently not technologically feasible.Analytical and numerical methods and hardware testing were used to help develop the deployable external airbags concept. Various Finite Element (FE) models at different stages were developed and an extensive number of iterations were conducted to help optimize airbag and inflator parameters to achieve desired targets. The concept development was executed and validated in two phases. This paper covers Phase II ONLY, which includes: (1) Re-design of the airbag geometry, pressure, and deployment strategies; (2) Further validation using a Via sled test of a 48 kph perpendicular side impact of an SUV-type impactor against a stationary car with US-SID-H3 crash dummy in the struck side; (3) Design of the reaction surface necessary for the bumper airbag functionality. The concept was demonstrated through live deployment of external airbags with a reaction surface in a full-scale perpendicular side impact of an SUV against a stationary passenger car at 48 kph. This research investigated only the concept of the inflatable devices since pre-crash sensing development was beyond the scope of this research.The concept design parameters of the bumper and grille airbags are presented in this paper. Full vehicle-to-vehicle crash test results, Via sled test, and simulation results are also presented. Head peak acceleration, Head Injury Criteria (HIC), Thoracic Trauma Index (TTI), and Pelvic acceleration for the SID-H3 dummy and structural intrusion profiles were used as performance metrics for the bumper and grille airbags. Results obtained from the Via sled tests and the full vehicle-to-vehicle tests with bumper and grille airbags were compared to those of baseline test results with no external airbags.

Recent epidemiological studies have identified that thoracic side airbags may vary in efficacy to reduce injury severity in side impact crash scenarios, while previous experimental and epidemiological studies have presented contrasting results. This study aimed to quantify the variations in occupant response in side impact conditions using a human body computational model integrated with a full vehicle model. The model was analyzed for a Moving Deformable Barrier side impact at 61 km/h to assess two pre-crash arm positions, the incorporation of a seatbelt, and a thorax air bag on thorax response. The occupant response was evaluated using chest compression, the viscous criterion and thoracic spinal curvature. The arm position accounted for largest changes in the thorax response (106%) compared to the presence of the airbag and seatbelt systems (75%). It was also noted that the results were dependant on the method and location of thorax response measurement and this should be investigated further. Assessment using lateral displacement of the thoracic spine correlated positively with chest compression and Viscous Criterion, with the benefit of evaluating whole thorax response and provides a useful metric to compare occupant response for different side impact safety systems. The thoracic side airbag was found to increase the chest compression for the driving arm position (+70%), and reduced the injury metrics for the vertical arm position (−17%). This study demonstrated the importance of occupant arm position on variability in thoracic response, and provides insight for future design and optimization of side impact safety systems.

Packing soft-sheet materials of approximately zero bending stiffness using Soft Origami (origami patterns applied to soft-sheet materials) into cylindrical volumes and their deployment via mechanisms or internal pressure (inflation) is of interest in fields including automobile airbags, deployable heart stents, inflatable space habitats, and dirigible and parachute packing. This paper explores twofold patterns, the ‘flasher’ and the ‘inverted-cone fold’, for packing soft-sheet materials into cylindrical volumes. Two initial packing methods and mechanisms are examined for each of the flasher and inverted-cone fold patterns. An application to driver’s side automobile airbags is performed, and deployment tests are completed to compare the influence of packing method and origami pattern on deployment performance. Following deployment tests, two additional packing methods for the inverted-cone fold pattern are explored and applied to automobile airbags. It is shown that modifying the packing method (using different methods to impose the same base pattern on the soft-sheet material) can lead to different deployment performance. In total, two origami patterns and six packing methods are examined, and the benefits of using Soft Origami patterns and packing methods are discussed. Soft Origami is presented as a viable method for efficiently packing soft-sheet materials into cylindrical volumes.

Objective: Insurance Institute for Highway Safety (IIHS) high-hooded side impacts were analyzed for matched vehicle tests with and without side airbags. The comparison provides a measure of the effectiveness of side airbags in reducing biomechanical responses for near-side occupants struck by trucks, SUVs, and vans at 50 km/h. Method: The IIHS moving deformable barrier (MDB) uses a high-hooded barrier face. It weighs 1,500 kg and impacts the driver side perpendicular to the vehicle at 50 km/h. SID IIs dummies are placed in the driver and left second-row seats. They represent fifth percentile female occupants. IIHS tests were reviewed for matches with one test with a side airbag and another without it in 2003–2007 model year (MY) vehicles. Four side airbag systems were evaluated: (1) curtain and torso side airbags, (2) head and torso side airbag, (3) curtain side airbag, and (4) torso side airbag. There were 24 matched IIHS vehicle tests: 13 with and without a curtain and torso side airbags, 4 with and without a head and torso side airbag, 5 with and without a side curtain airbag, and 2 with and without a torso airbag. The head, chest, and pelvis responses were compared for each match and the average difference was determined across all matches for a type of side airbag. Results: The average reduction in head injury criterion (HIC) was 68 ± 16% (P < .001) with curtain and torso side airbags compared to the HIC without side airbags. The average HIC was 296 with curtain and torso side airbags and 1,199 without them. The viscous response (VC) was reduced 54 ± 19% (P < .005) with curtain and torso side airbags. The combined acetabulum and ilium force (7 ± 15%) and pelvic acceleration (−2 ± 17%) were essentially similar in the matched tests. The head and torso side airbag reduced HIC by 42 ± 30% (P < .1) and VC by 32 ± 26% compared to vehicles without a side airbag. The average HIC was 397 with the side head and torso airbag compared to 729 without it. The curtain airbag and torso airbag only showed lower head responses but essentially no difference in the chest and pelvis responses. Conclusion: The curtain and torso side airbags effectively reduced biomechanical responses for the head and chest in 50 km/h side impacts with a high-hooded deformable barrier. The reductions in the IIHS tests are directionally the same as estimated fatality reductions in field crashes reported by NHTSA for side airbags.

The lower extremity of the occupant represents the most frequently injured body region in motor vehicle crashes. Knee airbags (KABs) have been implemented as a potential countermeasure to reduce lower extremity injuries. Despite the increasing prevalence of KABs in vehicles, the biomechanical interaction of the human lower extremity with the KAB has not been well characterized. This study uses computational models of the human body and KABs to explore how KAB design may influence the impact response of the occupant's lower extremities.The analysis was conducted using a 50th percentile male occupant human body model with deployed KABs in a simplified vehicle interior. The 2 common KAB design types, bottom-deploy KAB (BKAB) and rear-deploy KAB (RKAB), were both included. A state-of-the-art airbag modeling technique, the corpuscular particle method, was adopted to represent the deployment dynamics of the unfolding airbags. Validation of the environment model was performed based on previously reported test results. The kinematic responses of the occupant lower extremities were compared under both KAB designs, 2 seating configurations (in-position and out-of-position), and 3 loading conditions (static, frontal, and oblique impacts). A linear statistical model was used to assess factor significance considering the impact responses of the occupant lower extremities.The presence of a KAB had a significant influence on the lower extremity kinematics compared to no KAB (P.05) by providing early restraint and distributing contact force on the legs during airbag deployment. For in-position occupants, the KAB generally tended to decrease tibia loadings. The RKAB led to greater lateral motion of the legs compared to the BKAB, resulting in higher lateral displacement at the knee joint and abduction angle change (51.2 ± 21.7 mm and 15° ± 6.0°) over the dynamic loading conditions. Change in the seating position led to a significant difference in occupant kinematic and kinetic parameters (P.05). For the out-of-position (forward-seated) occupant, the earlier contact between the lower extremity and the deploying KAB resulted in 28.4° ± 5.8° greater abduction, regardless of crash scenarios. Both KAB types reduced the axial force in the femur relative to no KAB. Overall, the out-of-position occupant sustained a raised axial force and bending moment of the tibia by 0.8 ± 0.2 kN and 21.1 ± 8.7 Nm regardless of restraint use.The current study provided a preliminary computational examination on KAB designs based on a limited set of configurations in an idealized vehicle interior. Results suggested that the BKAB tended to provide more coverage and less leg abduction compared to the RKAB in oblique impact and/or the selected out-of-position scenario. An out-of-position occupant was associated with larger abduction and lower extremity loads over all occupant configurations. Further investigations are recommended to obtain a full understanding of the KAB performance in a more realistic vehicle environment.

Independent verification of the accuracy of data from Event Data Recorders (EDRs) is useful when using the information to help reconstruct a crash. To this end, the accuracy of the EDR function of the Airbag Control Module (ACM) was tested on 2010 and 2011 Toyota Camry sedans during straight line operation. During steady state operation, and maximum ABS-braking runs starting from approximately 80 km/h (50 mph), and 113 km/h (70 mph), non-deployment events were artificially induced to store event data. Following each run, the EDR was imaged using the Bosch Crash Data Retrieval (CDR) system. The CDR reported speed values were compared to Racelogic VBox differential GPS speed records. Data recorders were also used to monitor the vehicle Controller Area Network (CAN) bus traffic, including the indicated speed, brake pressure, engine RPM, and accelerator pedal position. The speed and RPM reporting algorithms stated in CDR Data Limitations were confirmed. Exemplar graphs of EDR-reported speed/brake/RPM/accel pedal data versus GPS speed and CAN bus data are presented and discussed. The timing of the reported data with respect to the event is also discussed. The difference between vehicle speed recorded by the EDR and the GPS speed during steady state operation varied from +0.4 to −2.3 km/h, with the EDR typically reporting lower than the GPS. During heavy braking the difference in speed was observed to be from −7 to +15 km/h, with wheel slip causing negative differences, and time delay since the last CAN bus update causing positive differences. Language: en

Nij, a function of upper neck forces and moment, plays a dominant role in the vehicle's star rating under the new NHTSA NCAP front impact program. This is mainly due to an artifact in the mapping of the Nij into the "risk" value used in the star rating, and the fact that the neck region is not weighted appropriately to reflect its real world significance relative to the other body regions in the NCAP rating. New test data also show that compared with the 50th male driver Nij, the 5th female passenger Nij is significantly more challenging to contain and therefore it is more dominant in the star rating. This paper describes the Hybrid III dummy head and neck impact response and provides a method to determine the external force acting on the head. The force and its acting point on the head are determined from head acceleration, angular acceleration, and the upper neck forces. This paper also analyzes the neck bending mechanism and the associated forces, and how the thorax rotation and translation can affect the upper neck forces. It discusses how the airbag shape and stiffness can affect the external force acting point and direction, and how the force affects the neck internal forces. The analyses have focused on the response of the 5th female dummy neck due to the aforementioned practical difficulty with its Nij. The analytical methods presented should aid in the understanding of vehicle restraint systems. Language: en

This study aims to analyze the effects of environment, vehicle and driver characteristics on the risky driving behavior at work zones. A decision tree is developed using the classification and regression tree (CART) algorithm to graphically display the relationship between the risky driving behavior and its influencing factors. This approach could avoid the inherent problems occurred in the conventional logistic regression models and further improve the model prediction accuracy. Based on the Michigan M-94/I-94/I-94BL/I-94BR highway work zone driving behavior data, the decision tree comprising 33 leaf nodes is built. Bad weather, poor road and light conditions, partial/no access control, no traffic control devices, turning left/right and driving in an old vehicle are found to be associated with the risky driving behavior at work zones. The middle-aged drivers, who are going straight ahead in their vehicles with medium service time and equipped with an airbag system, are more likely to take risky behavior at lower work zone speed limits. Further, the middle-aged male drivers engage in risky driving behavior more frequently than the middle-aged female drivers. The number of lanes exhibits opposing effects on risky behavior under different traveling conditions. More specifically, the risky driving behavior is associated with the single-lane road under bad light or weather conditions while drivers are more likely to engage in risky behavior on the multi-lane road under good light conditions.

Approximately 66 per cent of all airbag deployments in the USA result in at least one skin injury, with 47 per cent of these skin injuries attributed directly to the airbag deployment. The purpose of the present study was to evaluate the risk of skin abrasions from the airbag fabric seam design by using a new shear testing methodology. High-rate shear loading was performed with a pneumatic impactor that propelled a section of airbag fabric across porcine skin at 85 m/s. Twenty-seven tests (three control and 24 with fabric) were performed using eight different seam designs. A 40 cm × 10 cm section of airbag fabric with each seam was forced across a 5 cm × 5 cm section of fresh porcine skin that was acquired within 2 h post-mortem. No abrasions were observed in the three control tests, but abrasions were observed in all 24 of the tests conducted using airbag fabric. The unturned, sewn seam orientation resulted in significantly more severe abrasions than the woven, unturned seam orientation ( P = 0.01). This new system and results illustrate that different seam designs can result in different skin abrasion risk. Moreover, the data show that severe abrasions can be caused by normal pressures well below the 1.75 MPa injury threshold previously published.

This paper reports on the work of computer simulations carried out at Coventry University as part of the European 6th Framework HeliSafe TA project, which considered the potential improvements in occupant safety for civil helicopters. A multi-body systems approach with additional use of finite elements for critical components such as a pilot airbag and the harnesses was adopted in the computer models to simulate helicopter crash/rollover scenarios and to investigate the effectiveness of occupant protection systems deployed during helicopter crash scenarios. ADAMS and Madymo simulations of helicopter impact/rollover events were demonstrated. A cabin/cockpit model of a Bell UH-1D helicopter was developed to replicate the physical crash test setup and a parametric study for the pilot airbag and a range of harness concepts was performed. The use of validated multi-body systems-based cabin/cockpit models has proved to be effective in the development of new restraint system concepts for occupant protection.

An important part of any model of vehicle crashes is the development of a procedure to estimate crash injury severity. After reviewing existing models of crash severity, this paper outlines the development of a modelling approach aimed at measuring the injury severity of people in two-vehicle road crashes. This model can be incorporated into a discrete event traffic simulation model, using simulation model outputs as its input. The model can then serve as an integral part of a simulation model estimating the crash potential of components of the traffic system. The model is developed using Newtonian Mechanics and Generalised Linear Regression. The factors contributing to the speed change (ΔV(s)) of a subject vehicle are identified using the law of conservation of momentum. A Log-Gamma regression model is fitted to measure speed change (ΔV(s)) of the subject vehicle based on the identified crash characteristics. The kinetic energy applied to the subject vehicle is calculated by the model, which in turn uses a Log-Gamma Regression Model to estimate the Injury Severity Score of the crash from the calculated kinetic energy, crash impact type, presence of airbag and/or seat belt and occupant age. Language: en

The purpose of this research is to analyse the influence of steering control devices for disabled people on passive safety. It is based on the advances made in the modelling and simulation of the driver position and in the suit verification test. The influence of these devices is studied through airbag deployment and/or its influence on driver safety. We characterise the different adaptations that are used in adapted cars that can be found mounted in vehicles in order to generate models that are verified by experimental test. A three-dimensional design software package was used to develop the model. The simulations were generated using a dynamic simulation program employing LS-DYNA finite elements. This program plots the geometry and assigns materials. The airbag is shaped, meshed and folded just as it is mounted in current vehicles. The thermodynamic model of expansion of gases is assigned, and the contact interfaces are defined. Static tests were carried out on the deployment of the airbag to contrast with and to validate the computational models and to measure the behaviour of the airbag when there are steering adaptations mounted in the vehicle. © 2011 Taylor & Francis.

To overcome the disadvantage of existing fast airtight devices, a latest-model airbag type fast airtight device was devised. Operating principle, structure and installation procedure of the device are presented in detail. Based on related technical parameters of return airway section on working face 15108 of Shi Gang Coal Mine, ANSYS analysis model was created. With a certain pressure and temperature condition, stress and strain in x, y and z directions of the airbag were calculated and the results proved the feasibility of the design proposal. Through field test and analysis of experiment results, the advantage and disadvantage of the latest-model fast airtight device were summarized, in hope to offer some inspiration to the development of airbag type mine airtight device.