Search

Electrospinning was introduced as a novel technique for preparing controlled-release (CR) amorphous solid dispersions (SD) and polymeric nanofibers of a poorly water-soluble drug. Piroxicam (PRX) was used as a low-dose poorly-soluble drug and hydroxypropyl methylcellulose (HPMC) as an amorphous-state stabilising carrier polymer in nanofibers. Raman spectroscopy, X-ray powder diffraction (XPRD), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were used in the physical characterisation of the CR-SD nanofibers. Special attention was paid on the effects of a polymer and solvent system on the solid-state properties and physical stability of nanofibers. The average dry diameter of the electrospun CR-SD nanofibers ranged from 400 to 600 nm (SEM). PRX existed in amorphous form in the nanofibers immediately after fabrication and after a short-term (3-month) aging at low temperature (6-8 °C/0% RH) and ambient room temperature (22 °C/0% RH). At higher temperature and humidity (30 °C/85% RH), however, amorphous PRX in the nanofibers tended to slowly recrystallise to PRX form III. The electrospun CR-SD nanofibers exhibited a short lag-time, the absence of initial burst release and zero-order linear CR dissolution kinetics. In conclusion, electrospinning can be used to fabricate supersaturating CR-SD nanofibers of PRX and HPMC, and to stabilise the amorphous state of PRX., (Copyright © 2014 Elsevier B.V. All rights reserved.)

We showed that scanning white light interferometry (SWLI) can provide nanometer depth resolution in 3D topographic analysis of electrospun drug-loaded nanofibrous mats without sample preparation. The method permits rapidly investigating geometric properties (e.g. fiber diameter, orientation and morphology) and surface topography of drug-loaded nanofibers and nanomats. Electrospun nanofibers of a model drug, piroxicam (PRX), and hydroxypropyl methylcellulose (HPMC) were imaged. Scanning electron microscopy (SEM) served as a reference method. SWLI 3D images featuring 29 nm by 29 nm active pixel size were obtained of a 55 μm × 40 μm area. The thickness of the drug-loaded non-woven nanomats was uniform, ranging from 2.0 μm to 3.0 μm (SWLI), and independent of the ratio between HPMC and PRX. The average diameters (n=100, SEM) for drug-loaded nanofibers were 387 ± 125 nm (HPMC and PRX 1:1), 407 ± 144 nm (HPMC and PRX 1:2), and 290 ± 100 nm (HPMC and PRX 1:4). We found advantages and limitations in both techniques. SWLI permits rapid non-contacting and non-destructive characterization of layer orientation, layer thickness, porosity, and surface morphology of electrospun drug-loaded nanofibers and nanomats. Such analysis is important because the surface topography affects the performance of nanomats in pharmaceutical and biomedical applications., (Copyright © 2013 Elsevier B.V. All rights reserved.)

The aim of the present study was two-fold: (1) to investigate the effect of pH and presence of surfactant sodium lauryl sulphate (SLS) on the solubility and dissolution rate of two solid-state forms of piroxicam (PRX), anhydrate (PRXAH) and monohydrate (PRXMH), and (2) to quantitatively assess the solid-phase transformation of PRXAH to PRXMH in slurry with a special interest to the impact on the solubility and dissolution behavior of the drug. X-ray powder diffractometry (XRPD), Raman spectroscopy and scanning electron microscopy (SEM) were used for characterization of the solid-state forms. Phase transformation was monitored in slurry by means of in-line Raman spectroscopy, and the partial least squares (PLS) regression model was used for predicting the amount of PRXMH. The results showed that the solubility and dissolution rate of PRXAH were higher compared to PRXMH at different pHs. The pH and presence of SLS together affected the solubility and dissolution rate of different PRX forms. The lowest solubility values and dissolution rates for PRX forms were observed in distilled water (pH 5.6) at 37 °C. The changes in the dissolution rate could be explained by the hydrate formation during solubility testing. The rate of hydrate formation was also dependent on the pH of the dissolution medium., (Copyright © 2012 Elsevier B.V. All rights reserved.)

We investigated and monitored in situ the wetting and dissolution properties of polymeric nanofibers and determined the solid-state of a drug during dissolution. Piroxicam (PRX) was used as a low-dose and poorly-soluble model drug, and hydroxypropyl methylcellulose (HPMC) and polydextrose (PD) were used as carrier polymers for electrospinning (ES). The initial-stage dissolution of the nanofibers was monitored in situ with three-dimensional white light microscopic interferometry (SWLI) and high-resolution optical microscopy. The physical solid-state characterization of nanofibers was performed with Raman spectroscopy, X-ray powder diffraction (XRPD), and scanning electron microscopy (SEM). We showed that PRX recrystallizes in a microcrystalline form immediately after wetting of nanofibers, which could lead to enhanced dissolution of drug. Initiation of crystal formation was detected by SWLI, indicating: (1) that PRX was partially released from the nanofibers, and (2) that the solid-state form of PRX changed from amorphous to crystalline. The amount, shape, and size of the PRX crystals depended on the carrier polymer used in the nanofibers and dissolution media (pH). In conclusion, the present nanofibers loaded with PRX exhibit a quasi-dynamic dissolution via recrystallization. SWLI enables a rapid, non-contacting, and non-destructive method for in situ monitoring the early-stage dissolution of nanofibers and regional mapping of crystalline changes (re-crystallization) during wetting. Such analysis is crucial because the wetting and dissolution of nanofibers can greatly influence the performance of nanofibrous drug delivery systems in pharmaceutical and biomedical applications. [ABSTRACT FROM AUTHOR]