Search

Metal halide perovskite solar cells (MHPSCs) hold great promise related to their high efficiency and low fabrication costs, but their long-term stability under environmental conditions remains a major challenge. In this study, we demonstrate an effective protection strategy to enhance the stability of MHPSCs through the incorporation of a double passivation layer based on an adamantane-based plasma polymer (ADA) at both the electron transport layer (ETL)/perovskite and perovskite/hole transport layer (HTL) interfaces. Our results show that the implemented ADA deposition technique is compatible with delicate substrates such as perovskites thin films, as their optical, morphological and optoelectronic properties are unaltered upon ADA deposition. At the same time, it provides effective protection to the perovskite material in high humidity environments. The ADA-double passivation not only reduces the formation of mobile ionic defects that cause additional recombination, but also significantly reduces humidity-induced degradation and mitigates the photocatalytic degradation caused by TiO2 under UV exposure. Stability tests performed under 100% relative humidity and continuous AM 1.5G illumination (ISOS-L-1) show that ADA dual passivated devices retained 80% of their initial efficiency after 4000 minutes, while reference samples dropped to 30%. The enhanced performance of ADA-passivated cells is attributed to protective nature of the plasma polymer layer resulting in a preservation of photocurrent and the prevention of new recombination routes. This dual passivation strategy offers a promising route to improve the environmental stability of PSCs and extend their operational lifetime.

The ultimate step towards the exploitation of water as a clean and renewable energy source addresses the energies stored in the low frequencies of liquid flows, which demands flexible solutions to adapt to multiple scenarios, from raindrops to waves, including water moving in pipelines and microdevices. Thus, harvesting low-frequency flows is a young concept compared to solar and wind powers, where triboelectric nanogenerators have been revealed as the most promising relevant actors. However, despite widespread attempts by researchers, the drop energy harvesters' output power is still low, mainly because of the limitations in candidates endowed with ideal triboelectric and wetting properties and also the non-optimal and centimetre-scale device architecture that prevents the conversion of the complete kinetic energy of impinging drops. Herein, we disclose a microscale triboelectric nanogenerator that can harvest a high density of electrical power from drops through a single, submillisecond, long-lasting step. The mechanism relies on an instantaneous electrical capacitance variation owing to the high-speed contact of the drops with the electrodes' active area. We discuss the role of the precharged effect of the triboelectric surface in the time characteristic of the conversion event. The capacitive and microscale structure of the device is endowed with a small form factor that allows for the production of densely packed arrays. The proposed architecture can be adjusted to different liquids and scales and is compatible with a variety of triboelectric surfaces, including flexible, transparent, and thin-film approaches., Comment: 23 pages, 6 figures in main text, 9 figures in Supporting Information, videos available from the authors

Early results on the plasma deposition of dielectric thin films on acoustic wave (AW) activated substrates revealed a densification pattern arisen from the focusing of plasma ions and their impact on specific areas of the piezoelectric substrate. Herein, we extend this methodology to tailor the plasma deposition of metals onto AW-activated LiNbO3 piezoelectric substrates. Our investigation reveals the tracking of the initial stages of nanoparticle (NP) formation and growth during the submonolayer deposition of silver. We elucidate the specific role of AW activation in reducing particle size, enhancing particle circularity, and retarding NP agglomeration and account for the physical phenomena making these processes differ from those occurring on non-activated substrates. We provide a comparative analysis of the results obtained under two representative plasma conditions: diode DC sputtering and magnetron sputtering. In the latter case, the AW activation gives rise to a 2D pattern of domains with different amounts of silver and a distinct size and circularity for the silver NPs. This difference was attributed to the specific characteristics of the plasma sheath formed onto the substrate in each case. The possibilities of tuning the plasmon resonance absorption of silver NPs by AW activation of the sputtering deposition process are discussed., Comment: 26 pages, 8 figures

Hybrid organometal halide perovskites (HP) present exceptional optoelectronic properties, but their poor long-term stability is a major bottleneck for their commercialization. Herein, we present a solvent-free approach to growing single-crystal organic nanowires (ONW), nanoporous metal oxide scaffolds, and HP to form a core@multishell architecture. The synthetic procedure is carried out under mild vacuum conditions employing thermal evaporation for the metal-free phthalocyanine (H2Pc) nanowires, which will be the core, plasma-enhanced chemical vapor deposition (PECVD) for the TiO2 shell, and co-evaporation of lead iodide (PbI2) and methylammonium iodide (CH3NH3I / MAI) for the CH3NH3PbI3 (MAPbI3 / MAPI) perovskite shell. We present a detailed characterization of the nanostructures by (S)-TEM and XRD, revealing a different crystallization of the hybrid perovskite depending on the template: while the growth on H2Pc nanowires induces the typical tetragonal structure of the MAPI perovskite, a low-dimensional phase (LDP) was observed on the one-dimensional TiO2 nanotubes. Such a combination yields an unprecedentedly stable photoluminescence emission over 20 hours and over 300 hours after encapsulation in polymethyl methacrylate (PMMA) under different atmospheres including N2, air, and high moisture levels. In addition, the unique one-dimensional morphology of the system, together with the high refractive index HP, allows for a strong waveguiding effect along the nanowire length.

Dye Sensitized Solar Cells (DSSCs) have recently regained attention for indoor light harvesting and powering wireless devices. Advantages such as cost-effectiveness, flexibility, wide angular response, and lightweight design have driven the fostering of the implementation of advanced photonic architectures, dedicated photosensitizers and compatibility with wearable carriers. However, to fully exploit their potential, crucial aspects require further attention, in particular the improvement of spectral compatibility and low-light harvesting mechanisms, as well as the development of efficient photoanodes through high-yield scalable methods. In this article, we propose the use of nanocomposite photoanodes integrating mesoporous TiO2 (m-TiO2) nanoparticles, ITO nanotubes (NTs) and TiO2 anatase shells (ITO@TiO2 NTs) prepared by step-by-step method relying on mild temperature conditions and avoiding toxic precursors. These photoanodes outperform previous attempts to implement low-dimensional ITO and ITO@TiO2 nanowires and nanotubes for outdoor light conversion, demonstrating an outstanding PCE under low artificial light intensity of 24 % for at 0.014 mWcm-2, a 166 % increase compared to the conventional architectures. Advanced microstructural, optical, and electrochemical characterizations have revealed that the strong scattering effect of the light in the visible range coupled with enhanced charge collection at low-intensity illumination are the essential mechanisms responsible for such enhanced energy conversion. Remarkably, our devices retain up to 90% of the normal incidence efficiency even under glancing illumination, while conventional reference devices show a drop down to 50%.

The ability to control porosity in oxide thin films is one of the key factors that determine their properties. Despite the abundance of dry processes for the synthesis of oxide porous layers, the high porosity range is typically achieved by spin-coating-based wet chemical methods. Besides, special techniques such as supercritical drying are required to replace the pore liquid with air while maintaining the porous network. In this study, we propose a new method for the fabrication of ultra-porous titanium dioxide thin films at room or mild temperatures (T lower or equal to 120 degrees Celsius) by the sequential process involving plasma deposition and etching. These films are conformal to the substrate topography even for high-aspect-ratio substrates and show percolated porosity values above 85 percent that are comparable to advanced aerogels. The films deposited at room temperature are amorphous. However, they become partly crystalline at slightly higher temperatures presenting a distribution of anatase clusters embedded in the sponge-like structure. Surprisingly, the porous structure remains after annealing the films at 450 degrees Celsius in air, which increases the fraction of the embedded anatase nanocrystals. The films are antireflective, omniphobic, and photoactive becoming super-hydrophilic subjected to UV light irradiation The supported percolated nanoporous structure can be used as an electron-conducting electrode in perovskite solar cells. The properties of the cells depend on the aerogel film thickness reaching efficiencies close to those of commercial mesoporous anatase electrodes. This generic solvent-free synthesis is scalable and is applicable to ultra-high porous conformal oxides of different compositions with potential applications in photonics, optoelectronics, energy storage, and controlled wetting., Comment: 31 pages, 10 Figs. plus Supporting Information 7 pags, 6 figs. Full Paper

Microacoustic wave devices are essential components in the RF electronics and MEMS industry with increasing impact in various sensing and actuation applications. Reliable and smart operation of acoustic wave devices at low costs would cause a crucial advancement. Herein, we present the enablement of temperature and mechanical sensing capabilities in a Rayleigh-mode standing surface acoustic wave (sSAW) chip device by harnessing an acoustic shear plate wave mode using the same set of electrodes. Most importantly, this mode is excited by switching the polarity of the sSAW transducer electrodes by simple electronics, allowing for direct and inexpensive compatibility with an existing setup. We validated the method in the emergent topic of surface de-icing by continuously monitoring temperature and water liquid-solid phase changes using the plate wave mode, and on-demand Rayleigh-wave deicing with a negligible energy cost. The flexibility for adapting the system to different scenarios, loads and scalability opens the path to impact in lab-on-a-chip, IoT technology, and sectors requiring autonomous acoustic wave actuators., Comment: 8 pages, 3 figures

Nanogenerators and self-powered nanosensors have shown the potential to power low-consumption electronics and human-machine interfaces, but their practical implementation requires reliable, environmentally friendly and scalable, processes for manufacturing and processing. This article presents a plasma synthesis approach for the fabrication of piezoelectric nanogenerators (PENGs) and self-powered sensors on paper substrates. Polycrystalline ZnO nanocolumnar thin films are deposited by plasma-enhanced chemical vapour deposition on common paper supports using a microwave electron cyclotron resonance reactor working at room temperature yielding high growth rates and low structural and interfacial stresses. Applying Kinetic Monte Carlo simulation, we elucidate the basic shadowing mechanism behind the characteristic microstructure and porosity of the ZnO thin films, relating them to an enhanced piezoelectric response to periodic and random inputs. The piezoelectric devices are assembled by embedding the ZnO films in PMMA and using Au electrodes in two different configurations: laterally and vertically contacted devices. We present the response of the laterally connected devices as a force sensor for low-frequency events with different answers to the applied force depending on the impedance circuit, i.e. load values range, a behaviour that is theoretically analyzed. The vertical devices reach power densities as high as 80 nW/cm2 with a mean power output of 20 nW/cm2. We analyze their actual-scenario performance by activation with a fan and handwriting. Overall, this work demonstrates the advantages of implementing plasma deposition for piezoelectric films to develop robust, flexible, stretchable, and enhanced-performance nanogenerators and self-powered piezoelectric sensors compatible with inexpensive and recyclable supports, Comment: 30 pages, 8 figures in main text

Within these studies, atomic scale molecular dynamics simulations have been performed to analyze the behavior of water droplets and ice clusters on hydrophilic and hydrophobic surfaces subjected to high-frequency vibrations. The methodology applied herewith aimed at understanding the phenomena governing the anti-icing and de-icing process enabled by Surface Acoustic Waves (SAWs). The complex wave propagation was simplified by in-plane and out-of-plane substrate vibrations, which are relevant to individual longitudinal and transverse components of SAWs. Since the efficiency of such an active system depends on the energy transfer from the vibrating substrate to water or ice, the agents influencing such transfer as well as the accompanied phenomena were studied in detail. Apart from the polarization of the substrate vibrations (in-plane/out-of-plane), the amplitude and frequency of these vibrations were analyzed through atomic scale modeling. Further, the surface wettability effect was introduced as a critical factor within the simulation of water or ice sitting on the vibrating substrate. The results of these studies allow identifying the different phenomena responsible for water and ice removal from vibrating surfaces depending on the wave amplitude and frequency. The importance of substrate wetting for the ant-icing and de-icing has also been analyzed and discussed concerning the future design and optimization of SAW-based systems.

Migrating active deicing capabilities to transparent materials with low thermal conductivity has a high potential to improve the operations of several seminal industries in the automotive, robotic, energy, and aerospace sectors. However, the development of efficient and environmentally friendly deicing methods is yet in its infancy regarding their compatibility with end-user surfaces at relevant scales and real-world operations. Herein, we approach deicing through nanoscale surface activation enabled by surface acoustic waves (SAWs), allowing efficient on-demand deicing of surface areas spanning several square centimeters covered with thick layers of glace ice. We contemplate SAW-based deicing from a twofold perspective: First, we demonstrate its functionality both with a bulk piezoelectric material (LiNbO3) and a piezo-electric film (ZnO), the latter proving its versatile applicability to a large variety of functional materials with practical importance; second, we gain fundamental knowledge of the mechanisms responsible for efficient deicing using SAWs. In particular, we show that SAW vibrational modes easily transport energy over greater distances outside the electrode areas and efficiently melt large ice aggregates covering the materials' surfaces. In addition, the essential physics of SAW-based deicing is inferred from a carefully designed experimental and numerical study. We support our findings by providing macroscopic camera snapshots captured in situ inside a climate chamber during deicing and highly resolved laser-doppler vibrometer scans of the undisturbed wavefields at room temperature. Great care was taken to deposit the interdigital transducers (IDTs) used for SAW excitation only on ice-free areas close to the chip edges, leaving most of the substrate used for deicing unaltered and, as a matter of fact, demonstrating transparent deicing solutions., Comment: 15 pages including Supporting Information; 7 figures in the main text

Despite the youthfulness of hybrid halide perovskite solar cells, their efficiencies are currently comparable to commercial silicon and have surpassed quantum-dots solar cells. Yet, the scalability of these devices is a challenge due to their low reproducibility and stability under environmental conditions. However, the methods reported to date to tackle such issues recurrently involve the use of solvent methods that would further complicate their transfer to industry. Herein we present a reliable alternative relaying in the implementation of an ultrathin plasma polymer as passivation interface between the electron transport material and the hybrid perovskite layer. Such nanoengineering interface provides solar devices with increased long-term stability under ambient conditions. Thus, without consideringr any additional encapsulation step, the cells retain more than 80 % of their efficiency after being exposed to the ambient atmosphere for more than 1000 h. Moreover, this plasma polymer passivation strategy significantly improves the coverage of the mesoporous scaffold by the perovskite layer, providing the solar cells with enhanced performance as well as improved reproducibility.

We introduce herein the advanced application of low pressure plasma procedures for the development of piezo and triboelectric mode I hybrid nanogenerators. Thus, plasma assisted deposition and functionalization methods are presented as key enabling technologies for the nanoscale design of ZnO polycrystalline shells, the formation of conducting metallic cores in core@shell nanowires, and for the solventless surface modification of polymeric coatings and matrixes. We show how the perfluorinated chains grafting of PDMS provides a reliable approach to increase the hydrophobicity and surface charges at the same time that keeping the PDMS mechanical properties. In this way, we produce efficient Ag/ZnO convoluted piezoelectric nanogenerators supported on flexible substrates and embedded in PDMS compatible with a contact separation triboelectric architecture. Factors like crystal-line texture, ZnO thickness, nanowires aspect ratio, and surface chemical modification of the PDMS are explored to optimize the power output of the nanogenerators aimed for harvesting from low-frequency vibrations. Just by manual trigger-ing, the hybrid device can charge a microcapacitor to switch on an array of color LEDs. Outstandingly, this simple three-layer architecture allows for harvesting vibration energy in a wide bandwidth, thus, we show the performance characteristics for frequencies between 1 Hz to 50 Hz and demonstrate the successful activation of the system up to ca. 800 Hz, Comment: 17 pages, including Supporting Information Section, one Schematic, six figures

The eventual exploitation of one-dimensional nanomaterials yet needs the development of scalable, high yield, homogeneous, and environmentally friendly methods able to meet the requirements for the fabrication of under design functional nanomaterials. In this article, we demonstrate a vacuum and plasma one-reactor approach for the synthesis of the fundamental common element in solar energy and optoelectronics, i.e. the transparent conducting electrode but in the form of nanotubes and nanotrees architectures. Although the process is generic and can be used for a variety of TCOs and wide-bandgap semiconductors, we focus herein on Indium Doped Tin Oxide (ITO) as the most extended in the previous applications. This protocol combines widely applied deposition techniques such as thermal evaporation for the formation of organic nanowires serving as 1D and 3D soft templates, deposition of polycrystalline layers by magnetron sputtering, and removal of the template by simply annealing under mild vacuum conditions. The process variables are tuned to control the stoichiometry, morphology, and alignment of the ITO nanotubes and nanotrees. Four-probe characterization reveals the improved lateral connectivity of the ITO nanotrees and applied on individual nanotubes shows resistivities as low as 3.5 +/- 0.9 x 10-4 {\Omega}.cm, a value comparable to single-crystalline counterparts. The assessment of diffuse reflectance and transmittance in the UV-VIS range confirms the viability of the supported ITO nanotubes as a random optical media working as strong scattering layers. Further ability to form ITO nanotrees opens the path for practical applications as ultra-broadband absorbers in the NIR. The demonstrated low resistivity and optical properties of these ITO nanostructures open the way for their use in LEDs, IR shield, energy harvesting, nanosensors, and photoelectrochemical applications, Comment: 21 pages, 1 schematic, 6 figures, supporting information

The thin film configuration presents obvious practical advantages over the 1D implementation in energy harvesting systems such as easily manufacturing and processing and long lasting and stable devices. However, most of the ZnO-based piezoelectric nanogenerators (PENGs) reported so far relay in the exploitation of single-crystalline ZnO nanowires because their self-orientation in the c-axis and ability to accommodate long deformations resulting in a high piezoelectric performance. Herein, we show an innovative approach aiming to produce PENGs by combining polycrystalline ZnO layers fabricated at room temperature by plasma assisted deposition with supported small-molecule organic nanowires (ONWs) acting as 1D scaffold. The resulting hybrid nanostructure is formed by a single-crystalline organic nanowire conformally surrounded by a three dimensional (3D) ZnO shell that combines the mechanical properties of the organic core with the piezoelectric response of the ZnO layer. In a loop forward towards the integration of multiple functions within a single wire, we have also developed ONW@Au@ZnO nanowires including a gold shell acting as inner nanoscopic electrode. Thus, we have built and compare thin films and 3D core@shell ONW@ZnO and ONW@Au@ZnO PENGs showing output piezo-voltages up to 170 mV. The synergistic combination of functionalities in the ONW@Au@ZnO devices promotes an enhanced performance generating piezo-currents almost twenty times larger than the ONW@ZnO nanowires and superior to the thin film nanogenerators for equivalent and higher thicknesses., Comment: 18 pages, 1 Scheme, 2 Figures, 3 Figures in Supporting Information Section