Search

Advanced light management via front‐coated photonic nanostructures is a promising strategy to enhance photovoltaic (PV) efficiency through wave‐optical light‐trapping (LT) effects, avoiding the conventional texturing processes that induce the degradation of electrical performance due to increased carrier recombination. Titanium dioxide (TiO2) honeycomb arrays with different geometry are engineered through a highly‐scalable colloidal lithography method on flat crystalline silicon (c‐Si) wafers and tested on standard planar c‐Si interdigitated back‐contact solar cells (pIBCSCs). The photonic‐structured wafers achieve an optical photocurrent of 36.6 mA cm−2, mainly due to a broad anti‐reflection effect from the 693 nm thick nanostructured coatings. In contrast, the pIBCSC test devices reach 14% efficiency with 679 nm thick TiO2 nanostructures, corresponding to a ≈30% efficiency gain relative to uncoated pIBCSCs. In addition, several designed structures show unmatched angular acceptance enhancements in efficiency (up to 63% gain) and photocurrent density (up to 68% gain). The high‐performing (yet electrically harmless) LT scheme, here presented, entails an up‐and‐coming alternative to conventional texturing for c‐Si technological improvement that can be straightforwardly integrated into the established PV industry. [ABSTRACT FROM AUTHOR]

The present contribution aims to enhance solar cells' performance via the development of advanced luminescent down-shifting based on encapsulated nanostructured perovskite materials. Here, thin films of inorganic lead halide (CsPbBr3) perovskite nanocrystal luminophores were synthetized, by hot-injection, deposited on glass substrates by spin-coating, and encapsulated with parylene type C, via chemical vapor deposition, to protect and stabilize the films. The optical properties of these thin films were characterized by absorption, emission and 2D contour spectra, their structure by X-ray diffraction and X-ray photoelectron spectroscopy, and the morphology by Scanning Transmission Electron microscopy. I–V curve and spectral response nanocrystalline silicon photovoltaic (nc-Si:H PV) cells were studied in the absence and presence of the perovskite and parylene luminescent down-shifting layers. The incorporation of the CsPbBr3 nanocrystals and their encapsulation with the parylene type C polymeric coating led to an increase in the current generated and the spectral response of the PV cells in the regime of the nanocrystals' fluorescence emission. A 3.1% increase in the short circuit current density and a 5.6% increase in the power conversion efficiency were observed. [ABSTRACT FROM AUTHOR]

Photonic front‐coatings with self‐cleaning properties are presented as means to enhance the efficiency and outdoor performance of thin‐film solar cells, via optical enhancement while simultaneously minimizing soiling‐related losses. This is achieved by structuring parylene‐C transparent encapsulants using a low‐cost and highly‐scalable colloidal‐lithography methodology. As a result, superhydrophobic surfaces with broadband light‐trapping properties are developed. The optimized parylene coatings show remarkably high water contact angles of up to 165.6° and extremely low adhesion, allowing effective surface self‐cleaning. The controlled nano/micro‐structuring of the surface features also generates strong anti‐reflection and light scattering effects, corroborated by numeric electromagnetic modeling, which lead to pronounced photocurrent enhancement along the UV–vis–IR range. The impact of these photonic‐structured encapsulants is demonstrated on nanocrystalline silicon solar cells, that show short‐circuit current density gains of up to 23.6%, relative to planar reference cells. Furthermore, the improvement of the devices' angular response enables an enhancement of up to 35.2% in the average daily power generation. [ABSTRACT FROM AUTHOR]

Abstract Optical solutions are promising for Perovskite solar cell (PSC) technology, not only to increase efficiency, but also to allow thinner absorber layers (higher flexibility) and improve stability. This work optimized the combined anti-reflection and scattering properties of two types of light trapping (LT) structures, based on TiO 2 semi-spheroidal geometries with honeycomb periodicity, for application in PSCs with substrate configuration and different perovskite layer thicknesses. Their optically lossless material (TiO 2) allows the structures to be patterned in the final processing steps, integrated in the cells' top n contact, therefore not increasing the surface area of the PV layers and not degrading the electric performance via recombination. Therefore, this strategy circumvents the typical compromise of state-of-the-art LT approaches between optical improvements and electrical deterioration, which is particularly relevant for PSCs since their main recombination is caused by surface defects. When patterned on the cells' front, the wave-optical micro-features composing the LT structures yield up to 21% and 27% photocurrent enhancement in PSCs with conventional (500 nm thick) and ultra-thin (250 nm) perovskite layers, respectively; which are improvements close to those predicted by theoretical Lambertian limits. In addition, such features are shown to provide an important encapsulation role, preventing the cells' degradation from UV penetration. Graphical abstract fx1 Highlights • Novel light trapping designs optimized for high-efficient Perovskite solar cells. • Wave-optical front structures provide strong VIS anti-reflection & NIR scattering. • Incorporation in n contact prevents electric degradation while boosting absorption. • Record photocurrent enhancement (35%) demonstrated in thin (250 nm) Perovskite cell. • Photonic structures act as UV blocking layer, enhancing Perovskite cell stability. [ABSTRACT FROM AUTHOR]

Abstract: Thin film solar cells based in Cu(In,Ga)Se2 (CIGS) are among the most efficient polycrystalline solar cells, surpassing CdTe and even polycrystalline silicon solar cells. For further developments, the CIGS technology has to start incorporating different solar cell architectures and strategies that allow for very low interface recombination. In this work, ultrathin 350 nm CIGS solar cells with a rear interface passivation strategy are studied and characterized. The rear passivation is achieved using an Al2O3 nanopatterned point structure. Using the cell results, photoluminescence measurements, and detailed optical simulations based on the experimental results, it is shown that by including the nanopatterned point contact structure, the interface defect concentration lowers, which ultimately leads to an increase of solar cell electrical performance mostly by increase of the open circuit voltage. Gains to the short circuit current are distributed between an increased rear optical reflection and also due to electrical effects. The approach of mixing several techniques allows us to make a discussion considering the different passivation gains, which has not been done in detail in previous works. A solar cell with a nanopatterned rear contact and a 350 nm thick CIGS absorber provides an average power conversion efficiency close to 10%. [ABSTRACT FROM AUTHOR]

The interaction of light with wavelength-sized photonic nanostructures is highly promising for light management applied to thin-film photovoltaics. Several light trapping effects come into play in the wave optics regime of such structures that crucially depend on the parameters of the photonic and absorbing elements. Thus, multi-parameter optimizations employing exact numerical models, as performed in this work, are essential to determine the maximum photocurrent enhancement that can be produced in solar cells. Generalized spheroidal geometries and high-index dielectric materials are considered here to model the design of the optical elements providing broadband absorption enhancement in planar silicon solar cells. The physical mechanisms responsible for such enhancement are schematized in a spectral diagram, providing a deeper understanding of the advantageous characteristics of the optimized geometries. The best structures, composed of TiO 2 half-spheroids patterned on the cells' top surface, yield two times higher photocurrent (up to 32.5 mA/cm 2 in 1.5 µm thick silicon layer) than the same devices without photonic schemes. These results set the state-of-the-art closer to the theoretical Lambertian limit. In addition, the considered light trapping designs are not affected by the traditional compromise between absorption enhancement versus current degradation by recombination, which is a key technological advantage. [ABSTRACT FROM AUTHOR]

The present development of non-wafer-based photovoltaics (PV) allows supporting thin film solar cells on a wide variety of low-cost recyclable and flexible substrates such as paper, thereby extending PV to a broad range of consumer-oriented disposable applications where autonomous energy harvesting is a bottleneck issue. However, their fibrous structure makes it challenging to fabricate good-performing inorganic PV devices on such substrates. The advances presented here demonstrate the viability of fabricating thin film silicon PV cells on paper coated with a hydrophilic mesoporous layer. Such layer can not only withstand the cells production temperature (150 °C), but also provide adequate paper sealing and surface finishing for the cell's layers deposition. The substances released from the paper substrate are continuously monitored during the cell deposition by mass spectrometry, which allows adapting the procedures to mitigate any contamination from the substrate. In this way, a proof-of-concept solar cell with 3.4% cell efficiency (41% fill factor, 0.82 V open-circuit voltage and 10.2 mA cm−2 short-circuit current density) is attained, opening the door to the use of paper as a reliable substrate to fabricate inorganic PV cells for a plethora of indoor applications with tremendous impact in multi-sectorial fields such as food, pharmacy and security. [ABSTRACT FROM AUTHOR]

Ultrasonic spray pyrolysis deposition of ZnO-based materials offers an attractive high-throughput low-cost route towards industrial production of high-quality transparent conductive oxide (TCO) thin-films. In this work, undoped and aluminium-doped ZnO films have been grown employing ultrasonic spray pyrolysis at relatively low-temperate (300 °C), followed by a post-annealing treatment. The role of Al concentration in the starting solution, as well as the rapid thermal annealing (RTA) atmosphere, were investigated and correlated to the morphological, structural, electrical and optical properties of the films. The remarkable enhancement of electrical conductivity attained here is mainly ascribed to the combined effects of: (1) homogenous incorporation of Al 3+ into the ZnO matrix, which enhances crystal quality providing higher electronic mobility; and (2) the RTA which releases the localized electrons caused by oxygen absorption and thereby increases the free carrier density. Under optimum deposition conditions, a low resistivity and a high optical transmittance around 4 × 10 −3 Ω cm and 87%, respectively, were obtained. The application of the RTA post-process after low temperature growth has several advantages relative to the direct growth at high temperature (usually 400–575 °C), such as shorter growth time and lower cost associated to the spray pyrolysis equipment requirements and usage. The results suggest that the electrical and optical properties of the ZnO:Al films can be further improved for solar cell applications by controlling the temperature of the post-deposition annealing in reducing atmosphere. [ABSTRACT FROM AUTHOR]