Search

Calculating the efficiency of a solar cell depends on a precise knowledge of its area. Indeed, the photoresponse uniformity is essential to improve the manufacturing process. In this work we report on Laser Beam Induced Current measurements performed on CIG(S,Se)2 modules and Dye Sensitized Solar Cells. These measurements, performed via a green and a red HeNe lasers both operating at an optical irradiance of 1 Sun, allowed to obtain an accurate photoresponse map of the specimens and highlighted the non-uniformities with a spatial resolution of 400 μm and 80 μm, respectively.

Dye Sensitized Solar Cells (DSSCs) are nowadays more and more employed since they present lower production costs than traditional silicon photovoltaic devices. An interesting phenomenon affecting such devices consists in the fact that current density-voltage (J-V) characteristic can depend on the history of the cell prior to the measurement, which often can be assimilated to an anomalous hysteresis effect. In this work, we study such phenomenon on Ruthenium-based DSSCs through a series of measurements performed after applying different values of external electrical field to the cell. The measurements have been carried out both under simulated sunlight (AM1.5G - 1000 W/m2) and in the dark. We show that the initial electrical bias field changes the cell behavior not only when the sample is illuminated but also at dark condition.

In this work, we report on the electro-optical characterization of Dye Sensitized Solar Cells (DSSCs) which use ruthenium complexes as sensitizers. In particular, several kinds of measurements have been performed to study the electrical performances and the efficiency levels of the cells at different operating conditions. In detail, the measurements have been conducted at varying temperatures and hours of light soaking. Our results show that the short circuit current density J SC , the open circuit voltage V OC and the conversion efficiency η increase with the hours of light soaking, while they decrease with temperature. A thorough investigation on the light soaking process at the device level has been carried out, giving a wealth of experimental data which can be very useful to better single out and quantify the underlying physical phenomena and the effects on the cell parameters, which are still controversial among the scientific community. Finally, the ageing study demonstrates that the cell performance rapidly deteriorates in the first few months of exposure to light. All the obtained results are of great importance for a better understanding of the light soaking phenomenon and for improving the fabrication process of the DSSCs investigated during this study.

Dye Sensitized Solar Cells (DSSCs) are widely considered one of the most promising third generation photovoltaic devices, especially thanks to their relatively low cost if compared to conventional solar cells. An interesting phenomenon affecting such devices is the so-called light soaking effect, consisting in the increase of cell main electrical parameters after the exposition to solar light. In this work, starting from the experimental characterization carried out on Ruthenium-based DSSCs, we report on a series of numerical analysis performed to better describe the above-mentioned light soaking effect in order to show the relationship between such phenomenon and the main physical parameters involved in photovoltaic generation in DSSCs. Our results show a good agreement between the experimental and the simulated data, hence allowing us to explain the trends followed by the main electrical parameters of DSSCs when exposed to solar light.

In this paper, we present an experimental investigation on the performance of Ruthenium-based Dye Sensitized Solar Cells (DSSCs) at different irradiance levels, incident wavelengths and hours of illumination. In particular, the measurements have been aimed at studying the performance variation due to light soaking effect since this phenomenon has noteworthy practical implications, such as stability tests of DSSCs. Our results show that the short circuit current density, the open circuit voltage and the conversion efficiency η increase with the hours of light soaking. Finally, the observed phenomenon is reversible, and thus the performance decreases again when the cell is kept in the dark.

An interesting phenomenon occurring in Dye Sensitized Solar Cells (DSSCs) when exposed to an uninterrupted period of illumination is the so-called light soaking effect, which consists in the increase of the main electrical parameters of the cell, such as the photocurrent and the efficiency. Studying such an effect has noteworthy practical implications, ranging from the optimization of the manufacturing process to stability tests of DSSCs. In this paper, we present an experimental investigation on the performance variation, due to light soaking, of Ruthenium-based DSSCs.

Nowadays, a growing demand for free and clean energy requires the study and the development of new low-cost solar photovoltaic (PV) cells. Among them, Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes as sensitizers are assuming a great importance. The DSSCs under study are composed placing in succession a transparent conductive glass on which is screen-printed a mesoporous TiO2 thin film sensitized by a ruthenium based dye (N719) , an electrolytic solution containing a redox couple (I-/I3-) and another conductive glass covered by a thin transparent catalyst platinum film. In this work, we have measured the main photoelectrochemical parameters of the above mentioned DSSCs at different irradiance levels, incident wavelengths, temperatures and hours of light soaking.

In this paper, we measure the main photoelectrical parameters of Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes at different irradiance levels, incident wavelengths, temperatures and hours of light soaking

Nowadays, a growing demand for free and clean energy requires the study and the development of new low-cost solar photovoltaic (PV) cells. Among them, Dye Sensitized Solar Cells (DSSCs) based on ruthenium complexes as sensitizers are assuming a great importance. The DSSCs under study are composed placing in succession a transparent conductive glass on which is screen-printed a mesoporous TiO2 thin film sensitized by a ruthenium based dye (N719), an electrolytic solution containing a redox couple (I-/I3-) and another conductive glass covered by a thin transparent catalyst platinum film. In this work, we have measured the main photoelectrochemical parameters of the above mentioned DSSCs at different irradiance levels, incident wavelengths, temperatures and hours of light soaking.

We demonstrate an innovative CIGS-based solar cells model with a graded doping concentration absorber profile, capable of achieving high efficiency values. In detail, we start with an in-depth discussion concerning the parametrical study of conventional CIGS solar cells structures. We have used the wxAMPS software in order to numerically simulate cell electrical behaviour. By means of simulations, we have studied the variation of relevant physical and chemical parameters-characteristic of such devices-with changing energy gap and doping density of the absorber layer. Our results show that, in uniform CIGS cell, the efficiency, the open circuit voltage, and short circuit current heavily depend on CIGS band gap. Our numerical analysis highlights that the band gap value of 1.40 eV is optimal, but both the presence of Molybdenum back contact and the high carrier recombination near the junction noticeably reduce the crucial electrical parameters. For the above-mentioned reasons, we have demonstrated that the efficiency obtained by conventional CIGS cells is lower if compared to the values reached by our proposed graded carrier concentration profile structures (up to 21%). © 2015 Antonino Parisi et al.

Electrodeposition is a convenient technique for the development of low cost materials for photovoltaic (PV) device processing. Using a single step electrodeposition route, several groups have fabricated CIS (CuInSe) and CIGS (CuInGaSe) films. One of the most important requirements for successful application of one-step electrodeposition film formation is the ability to control composition of the deposited films and to develop polycrystalline microstructures with a low surface roughness and high sintered density.

Dye Sensitized Solar Cell (DSSC), usually referred as one of the most promising third generation photovoltaic devices, is an electrochemical device in which a molecule (i.e., the dye) chemisorbed onto the surface of a porous material absorbs the incident light and, thus, transfers an electron to the wide band gap semiconductor material. The injected electrons can diffuse through the semiconductor up to the collecting anode without the risk of recombination. The roles of the electrolyte which permeates the cell are to regenerate the ionized molecule and to implement a hole-transporting layer, allowing to repeat the abovementioned process. Thanks to this behaviour, semiconductors with large amounts of defects can be used with relatively good efficiency values. In a previous work, we have described the electro-optical characterization of DSSCs which use N719 ruthenium complex as the sensitizer dye, TiO2 as the wide band semiconductor material, triiodide/iodide as the electrolyte redox couple and platinum counter electrodes. Here we show our experimental results and the use of a solar cell model including all the different parts of the devices. In this way, we are able to explain the performance increase of our cells – in terms of Voc, Jsc and efficiency – with light soaking.