Search

The addition of methylammonium chloride (MACl) significantly improves the performance and stability of perovskite fabricated by two-step processes. However, its role in crystallization dynamics has not been thoroughly studied. In this work, a comparison study is carried out using different additions of MACl to investigate the impact of the perovskite crystallization dynamics. In situ grazing incidence wide-angle X-ray scattering (GIWAXS) observations during the annealing process of perovskite revealed that the amount of MACl significantly influences the crystallinity and orientation of the perovskite. Increasing the MACl addition enhances the crystallinity of the perovskite in the wet film's intermediate phase and strengthens the out-of-plane orientation of the FAPbI3 perovskite α-phase (001) planes during annealing. Moreover, it was found that both excessive and insufficient amounts of MACl introduce defects into the perovskite, which are detrimental to device performance. In contrast, an optimal ratio of MACl-9 mg leads to the formation of uniform and large-grained FAPbI3 perovskite films, with the longest carrier lifetimes (163.7 ns) compared to MACl-5 mg (68.4 ns) and MACl- 13 mg (120.1 ns). As a result, the fabricated MACl-9 mg-based solar cell achieved the highest efficiency (22.63%), which is higher than those of MACl-5 mg (21.47%) and MACl-13 mg (20.07%). [ABSTRACT FROM AUTHOR]

Phase transition during annealing in the two‐step sequential deposition has drawn intensive attention as its significance in fabricating superior perovskite films. However, previous works have not paid enough attention to the importance of the purified phase transition path in the crystallization process. Herein, different from the mixed paths in the conventional cognition, purified phase transition path for α‐FAPbI3 crystallization is achieved by introducing dimethylurea (DMU) into lead iodide (PbI2) precursor solution. The multifunctional molecule is found to design a penetrable porous PbI2 film and fundamentally regulate the perovskite crystallization by forming single phase transition path via the complete δ‐phase during annealing of perovskite. The role of DMU in purified transition path for α‐FAPbI3 crystallization is unraveled with in situ photoluminescence and grazing incidence wide‐angle x‐ray scattering (GIWAXS) investigation. The crystal quality of perovskite films is significantly improved, resulting in single crystal‐like film. The best‐performing perovskite solar cells (PSCs) deliver a power conversion efficiency of 24.75%, resulting from the higher FF of 83.25% and an improved long‐term stability up to 3600 h. This work highlights the importance of purified phase transition path for the superior crystal quality toward high‐performance perovskite photovoltaics. [ABSTRACT FROM AUTHOR]

Tin halide perovskite solar cells are promising for the next generation of highly efficient photovoltaics. Their commercialization can be accelerated by increasing their stability in moisture and oxygen. Herein, an n‐type organic molecule (IO‐4Cl) is applied as an interlayer between the perovskite films and electron transport layers in p‐i‐n structured devices. The electron‐rich indacenodithieno‐[3,2‐b]thiophene enhances electron transport, while the hydrocarbon side chains and rigid conjugated backbone isolate air. It is also shown that the C═O in IO‐4Cl can coordinate with Sn2+ on perovskite films' surface and grain boundaries to enhance perovskite crystal stability. In addition, IO‐4Cl slows down crystallization dynamics, resulting in lower non‐radiation recombination. The moisture ingress in the perovskite films is tracked under high relative humidity (RH) and it is found that IO‐4Cl can mitigate moisture infiltration. Finally, the devices with IO‐4Cl maintain 95% of the initial power conversion efficiency after 1200 h of storage in a nitrogen‐filled glovebox, and their stability in ambient air (60–80% RH) is significantly improved against pristine devices, thus demonstrating the beneficial effects of IO‐4Cl interlayer on device stability. [ABSTRACT FROM AUTHOR]

Organic–inorganic perovskite solar cells (PSCs) have achieved great attention due to their expressive power conversion efficiency (PCE) up to 25.7%. To improve the photovoltaic performance of PSCs, interface engineering between the perovskite and hole transport layer (HTL) is a widely used strategy. Following this concept, benzyl trimethyl ammonium chlorides (BTACls) are used to modify the wet chemical processed perovskite film in this work. The BTACl‐induced low dimensional perovskite is found to have a bilayer structure, which efficiently decreases the trap density and improves the energy level alignment at the perovskite/HTL interface. As a result, the BTACl‐modified PSCs show an improved PCE compared to the control devices. From device modeling, the reduced charge carrier recombination and promoted charge carrier transfer at the perovskite/HTL interface are the cause of the open‐circuit (Voc) and fill factor (FF) improvement, respectively. This study gives a deep understanding for surface modification of perovskite films from a perspective of the morphology and the function of enhancing photovoltaic performance. [ABSTRACT FROM AUTHOR]

The relatively lower crystallinity and random orientation of quantum well structures hinder carrier transport and limit the performance of formamidinium (FA) based low‐n 2D perovskite devices. In this work, the crystallization and quantum well orientation are fine tuned to achieve efficient low‐n FA based Ruddlesden–Popper perovskite solar cells. The effects of different ionic additives on the crystallization, orientation, and photovoltaic performance of FA based low‐n 2D perovskites are comparatively investigated. It is found that NH4+ and SCN− can significantly retard the heterogeneous crystallization of low‐n phases in the intermediate state, and drive the templated growth of quantum well structure with vertical orientation. The optimized photovoltaic device based on (BA)2(FA)3Pb4I13 achieved a power conversion efficiency (PCE) of 18.14%, setting the highest record for FA‐based low‐n 2D perovskite solar cells as far as it is known (average n = 4). The unencapsulated device exhibited excellent stability and maintained 93.3% of its original PCE at 85 °C, and 86.3% at 1 Sun illumination after 720 h in humid ambient condition. [ABSTRACT FROM AUTHOR]

2D perovskites possess superior humidity stability but inferior power conversion efficiency (PCE) compared with 3D perovskites due to their typically insulating spacers. Size of the spacer cation is determinative for the formation of 2D perovskite, and fullerene is believed not to be capable of templating 2D perovskite structure because of its larger size than the width of the lead‐halide octahedron despite its well‐known strong electron‐accepting ability. Herein, a novel amino‐functionalized fullerene derivative (abbreviated as C60‐BPAM) is developed and an 'improbable' spacer for 2D/3D hybrid perovskite solar cells (PSCs), achieving enhanced electron transport is applied. Unlike most of the reported alkylammonium spacers that are based on insulating organic tails, the incorporation of a highly conductive fullerene tail within C60‐BPAM2+ leads to increased electron density in 2D/3D perovskite and induces an additional built‐in electric field, facilitating electron transport in PSCs. Besides, the 2D/3D hybrid structure helps to passivate both of the shallow‐ and deep‐level defects within perovskite. As a result, the PCE of 2D/3D PSCs improves from 19.36% (3D MAPbI3 PSCs) to 20.21%. Moreover, the 2D/3D PSCs show significant improvement in the humidity stability compared to the 3D counterparts. [ABSTRACT FROM AUTHOR]

While there is promising achievement in terms of the power conversion efficiency (PCE) of perovskite solar cells (PSCs), long‐term stability has been considered the main obstacle for their practical application. In this work, the authors demonstrate the small monomer 2‐(dimethylamino) ethyl methacrylate (DMAEMA) with unsaturated carboxylic acid ester bond in the antisolvent for perovskite formation to improve the PCE and stability. The results show that DMAEMA is self‐polymerized and uniformly distributed in the film, contributing to the improved crystallinity of the perovskites. Equally important, it is found that there are newly established interactions of Pb2+ and DMAEMA, and iodine and ternary amine between DMAEMA and perovskites, which improves the uniformity of the lead (II) iodide vertical distribution along with the films and thus phase stability, as well as largely decreases defects density in the film. Overall, the inverted PSCs with DMAEMA exhibit a open‐circuit voltage of 1.10 V, short‐circuit current of 23.86 mA cm−2, fill factor of 0.82, and finally PCE reaches 21.52%. Meanwhile, the PSC stability is significantly improved due to the inhibition of the formation of iodine, reduction of the uncoordinated Pb2+, and suppression of phase segregation. [ABSTRACT FROM AUTHOR]

2D/3D mixed tin (Sn)‐based perovskites serving as excellent active layers possess a potential for enhancing film/device stabilities, open‐circuit voltage, and power conversion efficiency (PCE) of perovskite solar cells (PSCs). Unfortunately, the poor morphology and low film coverage of these 2D/3D perovskites jeopardize their device performance and stability. Herein, doping of hydroxyl‐rich d‐sorbitol into hole transport layer poly(3,4‐ethenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) can effectively address the PEDOT:PSS/perovskite interfacial issues. The multihydroxyl groups from d‐sorbitol can sufficiently anchor iodide ions ([SnI6]4− or free I−) of PEA0.1(FA0.75MA0.25)0.9SnI3 perovskite via hydrogen bond, which not only introduces more nucleation sites with improved crystallinity along the preferential crystal orientations, but also reduces the trap states' density and suppresses the iodide ions' migration. In the meanwhile, the content of SnI2 is reduced in the resulting perovskite films. All of these are conducive to form compact and smooth high‐quality perovskite films with less traps and enhanced stability. Benefitting from these, an inverted PSC with a champion PCE of 10.46% and a lifetime of 700 h (25% attenuation in N2) is eventually achieved. This work provides a promising approach to manufacture highly efficient and stable Sn‐based PSCs based on 2D/3D mixed perovskites. [ABSTRACT FROM AUTHOR]

Interfacial engineering is essential for facilitating carrier separation, charge extraction, and enhancing the stability in organic–inorganic perovskite solar cells (PSCs). Herein, a facile and effective method is demonstrated not only to tune the electronic performance of electron transporting layer (ETL) but also to passivate the defects at the interface between the ETL and perovskite. On the top of the tin(IV) oxide (SnO2) ETL, butylammonium chloride (BACl) and lead(II) iodide (PbI2) are introduced as interface to modify the ETL/perovskite interface. The PSCs with interface modified exhibit a power conversion efficiency (PCE) of 21.15%, compared to 18.33% for the device without interface modified. Such enhancement in efficiency is mainly attributed to a better energy band alignment, and the quality of perovskite films is improved through the interface modification, thus enhancing photogenerated charge extraction and leading to low charge carrier recombination at the interface of ETL/perovskite. Furthermore, the device with interface modified exhibits significant stability. This work provides an alternative strategy on the ETL/perovskite interface to obtain highly stable and efficient PSCs. [ABSTRACT FROM AUTHOR]

All‐inorganic lead halide perovskites are promising candidates for optoelectronic applications. However, fundamental questions remain over the component interaction in the perovskite precursor solution due to the limitation of the most commonly used solvents of N,N‐dimethylformamide (DMF) and dimethyl sulfoxide (DMSO). Here, we report an interaction tailoring strategy for all‐inorganic CsPbI3−xBrx perovskites by involving the ionic liquid solvent methylammonium acetate (MAAc). C=O shows strong interaction with lead (Pb2+) and N−H⋅⋅⋅I hydrogen bond formation is observed. The interactions stabilize the perovskite precursor solution and allow production of the high‐quality perovskite films by retarding the crystallization. Without the necessity for antisolvent treatment, the one‐step air‐processing approach delivers photovoltaic cells regardless of humidity, with a high efficiency of 17.10 % along with long operation stability over 1500 h under continuous light illumination. [ABSTRACT FROM AUTHOR]

One of the most important factors governing the photovoltaic efficiency and environmental stability of Perovskite Solar Cells (PSCs) is the quality of their perovskite films. However, the present study demonstrates that CH 3 NH 3 PbI 3 perovskite films after anti-solvent washing are far from perfect on the surface, where the crystallization degree is quite low with complex multi-phases associated with numerous defects and notable chemical inhomogeneity. Herein, we report a novel anti-solvent washing treatment simply using Hydrogen Iodide (HI) additive in chlorobenzene (CB) which can enormously improve CH 3 NH 3 PbI 3 films surface with high crystallization phase purity and chemical homogeneity, leading to excellent structural stability under humidity, heat and even tensile force. Based on such high quality films with defect-less surface, fabricated planar PSCs with an architecture of ITO/TiO 2 /CH 3 NH 3 PbI 3 /Spiro-OMeTAD/MoO x /Au present a champion PCE of 19.94% and improved stability under humidity. Moreover, fabricated flexible planar PSCs on PET/ITO substrates with a champion PCE of 17.32% are shown to be more robust under tensile force than their control devices. The present study thus not only provides more insight into the facile defects passivation process on the surface achieved via balancing halide ions, but also provides a practical but efficient treatment which can be widely used to fabricate high quality CH 3 NH 3 PbI 3 films for environmentally stable high performance device applications. [ABSTRACT FROM AUTHOR]

Abstract: In this contribution, a facile and universal method is successfully reported to fabricate perovskite solar cells (PSCs) with enhanced efficiency and stability. Through dissolving functional conjugated polymers in antisolvent chlorobenzene to treat the spinning CH3NH3PbI3 perovskite film, the resultant devices exhibit significantly enhanced efficiency and longevity simultaneously. In‐depth characterizations demonstrate that thin polymer layer well covers the top surface of perovskite film, resulting in certain surface passivation and morphology modification. More importantly, it is shown that through rational chemical modification, namely molecular fluorination, the air stability and photostability of the perovskite solar cells are remarkably enhanced. Considering the vast selection of conjugated polymer materials and easy functional design, promising new results are expected in further enhancement of device performance. It is believed that the findings provide exciting insights into the role of conjugated polymer in improving the current perovskite‐based solar cells. [ABSTRACT FROM AUTHOR]

Interface engineering resulting in good contact, enhanced transport capability, and matched energy levels is indispensable and critical for the development of high-performance planar perovskite solar cells (PSCs). Here, we report an excellent electron-transporting layer (ETL) that can simultaneously enhance the stability and efficiency of n-i-p planar PSCs. Large π-conjugated graphdiyne (GD) was introduced into cross-linkable fullerene [6,6]-phenyl-C61-butyric styryl dendron ester (PCBSD) to improve the film orientation. Raman spectroscopy and 2D grazing incidence X-ray diffraction (GIXRD) measurements revealed that a strong π–π stacking interaction occurred between GD and cross-linkable PCBSD (C-PCBSD), generating a face-on stacked composite film. The orientated C-PCBSD:GD films was favorable for the growth and crystallization of the subsequent perovskite films and provided the merits of superior electron mobility, efficient charge extraction and energy-level tailoring. In addition, the thermally annealed C-PCBSD:GD film provided an adhesive film network with sufficient solvent resistance. Consequently, the perovskite devices delivered a power conversion efficiency of 20.19% with obviously improved cell stability. This indicates a potential application of GD-modified cross-linkable fullerene as an ETL in n-i-p structure PSCs. The finding opens a new route to deposit the fullerene films with ordered orientation by 2D materials with large π-conjugation, and thus to control the subsequent perovskite crystallization. [ABSTRACT FROM AUTHOR]

The inherent defects (lead iodide inversion and iodine vacancy) in perovskites cause non‐radiative recombination and there is also ion migration, decreasing the efficiency and stability of perovskite devices. Eliminating these inherent defects is critical for achieving high‐efficiency perovskite solar cells. Herein, an organic molecule with multiple active sites (4,7‐bromo‐5,6‐fluoro‐2,1,3‐phenylpropyl thiadiazole, M4) is introduced to modify the upper interface of perovskites. When M4 interacts with the perovskite surface, the active bromine (Br) site interacts with lead (Pb) at the surface to repair iodine atomic vacancy defects. The fluorine (F) site of M4 interacts with Pb to correct octahedral crystal lattice distortions and eliminate PbI defects. Additionally, sulfur–iodine (S–I) interactions reduce I–I dimerization and eliminate IPb defects. It is also calculated that the energy level of M4 aligns with the band gap, promoting charge transfer. As a result, the perovskite devices achieve an efficiency of 25.1%, a stabilized power output (SPO) of 25.0%, a voltage of 1.19 V, and a fill factor of 85.2%. The device retains 95% of its initial efficiency after 2000 h of ageing in a nitrogen atmosphere. Thus, multi‐point cooperative passivation of surface defects provides an effective method to improve the efficiency and stability of perovskite solar cells. [ABSTRACT FROM AUTHOR]

Two‐step sequential deposition of perovskite films is proven efficient and compatible with large‐scale production. Nevertheless, its critically regulated environmental humidity often remains a burden, hindering its applications in reproducible fabrication of perovskite solar cells (PSCs). Herein, by introducing a water ethyl acetate (W‐EA) solution treatment before annealing, improved perovskite crystallinity and homogeneity in FA0.95‐xMAxCs0.05PbI3 films without additional composition regulation is achieved. In situ Grazing‐incidence Wide‐angle X‐ray Scattering experiments highlighted accelerated crystallization kinetics in W‐EA‐treated films, leading to high‐quality perovskite formation. PSCs based on this method reached an optimal power conversion efficiency of 25.01% and demonstrated enhanced moisture resistance, retaining 88% efficiency after 1000 h in ambient conditions. This W‐EA treatment simplifies the fabrication process, greatly reducing the need for controlled humidity, and offers insights into the role of water in perovskite film crystallization, with significant implications to produce high‐performance PSCs. [ABSTRACT FROM AUTHOR]

Blending perovskite with different cations has been successful in improving performance of perovskite solar cells, but the complex pathway of perovskite crystal formation remains a mystery, hindering its further development. In this paper, the detailed crystallization process of formamidinium lead iodide (FAPbI3) perovskite films doped by methylammonium lead bromide (MAPbBr3) additive was investigated by in situ grazing incident wide-angle X-ray scattering measurements during both spin coating and annealing. During spin-coating, it was found that the FAPbI3 perovskite precursor easily formed a mixture of black perovskite phase (α phase) and non-perovskite yellow phase (δ phase) after the addition of MAPbBr3, whereas only δ phase formed without MAPbBr3. The δ phase gradually converted to α phase during annealing and there was only α phase left in both films with and without MAPbBr3. However, the doped films presented high film quality without PbI2 residue in contrast to the undoped films. These findings imply that the MAPbBr3 additive can effectively suppress the formation of the unfavorable δ phase and trigger the formation of the optically active α phase even during spin-coating, which enhances the film quality possibly by removing the energy barriers from δ phase to α phase at room temperature. Finally, PSCs based on MAPbBr3-doped FAPbI3 were fabricated with a champion efficiency as high as 19.4% from 14.2% for the PSCs based on undoped FAPbI3. [ABSTRACT FROM AUTHOR]

Anti-solvent washing has been widely used in preparation of compact and uniform perovskite films. However, it often brings more surface defects in the prepared film. Additive PTB7 in anti-solvent is proven to significantly enhance perovskite crystallinity on the film surface. Finally, a champion power-conversion efficiency of 21.41% was achieved in PTB7-washed PSCs which retained over 90% of the initial PCE after 350 h using maximum power point tracking without being encapsulated. [Display omitted] • PTB7 significantly enhance perovskite film surface crystallinity, as evidenced by depth sensitive grazing incidence X-ray diffraction. • PTB7 molecules tend to interact with Pb atoms which slows down crystallization dynamics in the surface region for enhanced perovskite crystallinity and effectively passivates defects at perovskite grain boundary and film surface. • The alkyl chains in PTB7 were shown to improve film surface hydrophobicity. • The champion device obtained an elevated efficiency of 21.41% and improved stability. Low temperature solution-processed organic–inorganic hybrid perovskite films inevitably encounter defects especially on surface and at grain boundaries. Anti-solvent washing has been widely practiced in fabricating uniform and dense perovskite films, but unfortunately it could cause even more defects on surface. Herein, polymer PTB7 was introduced into anti-solvent as an additive to significantly enhance perovskite film surface crystallinity with fewer defects, as evidenced by depth sensitive grazing incidence X-ray diffraction. Such improvements could be attributed to the Lewis base coordination bonds formed between PTB7 and Pb atoms in the surface region which slow down crystallization dynamics for enhanced perovskite surface crystallinity and effectively passivate defects at the perovskite grain boundary and film surface. With PTB7 in anti-solvent, the fabricated perovskite solar cells (PSCs) achieved a champion power conversion efficiency (PCE) of 21.41% from that of 19.79% for the control devices without PTB7. In addition, the hydrophobic alkyl chains in PTB7 were shown to improve film surface hydrophobicity with enhanced environmental stability of both the fabricated films and PSCs. Thus, addition of PTB7 in anti-solvent is proven to effectively improve the performance and stability of PSCs which could be easily applied in the fabrication of PSCs and other perovskite-based optoelectronics. [ABSTRACT FROM AUTHOR]

[Display omitted] • Wide-bandgap polymers in organic photovoltaics provide a valuable toolbox for developing hole transport materials (HTMs). • Perovskite solar cells (PSCs) using dopant-free PBQx-TCl HTM demonstrated an efficiency of 24.12 % with a high V OC of 1.20 V and good operational stability (T 90 > 600 hours). Dopant-free polymer hole transport materials (HTMs) exhibit high thermal stability, hydrophobicity and film-processing capabilities, demonstrating excellent device efficiency and stability in perovskite solar cells (PSCs). Continued innovation of wide-bandgap polymers in organic photovoltaics (OPV) provides a valuable toolbox for developing polymeric HTMs. Here, we propose an effective molecule design for selecting structurally relevant polymers (D18, D18-Cl, PBQx-TCl) available for commercialization. We discover that the highly planar conjugated backbones play a crucial role in regulating the packing orientation of the film relative to the perovskite. The moderate aggregation with face-on packing orientation is conducive to the high-quality film, which is responsible for better contact with perovskite and superior charge extraction and transport. Simultaneously, these polymers with robust passivation enhanced the open circuit voltage (V OC) without additional passivation layers, streamlining the device process. Consequently, a PSC using dopant-free PBQx-TCl HTL demonstrated an efficiency of 24.12 % with a high V OC of 1.20 V and good operational stability (T 90 > 600 h). This work reveals transparent structure–function-performance relationships between molecules and devices, paving the way for the subsequent development of high-performance HTMs. [ABSTRACT FROM AUTHOR]

Indoor photovoltaics (IPVs) are favored for their speciality to provide sustainable and reliable energy for low-power electronic devices. As an ideal IPVs material, perovskite has been well explored in recent years. Herein, we focus on enhancing the photoelectric properties of the perovskite crystal under low light. By introducing N , N ′-bis(dimethylaminopropyl- N ‴-oxide)-perylene-3,4,9,10-tetracarboxidiimide (PDINO) into the perovskite, the crystallinity degree of the perovskite films are proven to be improved by synchrotron-based grazing incidence X-ray diffraction, thereby effectively enhancing the exciton transmission and separation in the perovskite. By using ultrafast spectroscopy, the influence of the optimized charge separation inside the perovskite under low light has been systematically analyzed. The final optimal perovskite solar cell showed an impressive indoor power conversion efficiency (PCE) of 37.9% under 1000 lux low light, and a PCE of 21.3% under 1 sun illumination. These findings proved doping of the perovskite by strong electron acceptors as a valid strategy for efficient charge transport, paving the way to their applications as IPVs. • The PDINO molecules can optimize the perovskite crystals formation and effectively reduce the defects in the film. • Analyzing tDOS and ultrafast spectroscopy, the defects passivation and the optimization of exciton separation were revealed. • A ∼37.9% efficient (1000 lux) indoor PSC is obtained based on PDINO-based device. [ABSTRACT FROM AUTHOR]

[Display omitted] • MoO 3 dope PTAA to lower its HOMO aligning better with MAPbI 3 VBM. • The hole transport and the interfacial hole extraction are enhanced. • The fabricated inverted planar PSCs achieve a champion PCE of 20.06%. The hole transport layer (HTL) plays a key role in determining the performance of planar perovskite solar cells (PSCs). Poly[bis(4-phenyl)(2,4, 6-triMethylphenyl)aMine] (PTAA), a polymer with good stability, is one of the promising HTL candidates for PSCs. However, notable interfacial carrier recombination limits the performance of PSCs based on PTAA HTL, due to the large gap between the highest-occupied molecular orbital (HOMO) of PTAA and the valance band maximum (VBM) of MAPbI 3 perovskite as well as the low intrinsic hole mobility of PTAA. Herein, PTAA was doped by 3 wt% of molybdenum oxide (MoO 3) to move down its HOMO by 0.16 eV, leading to a better matching with the MAPbI 3 perovskite. Meanwhile, the MoO 3 dopant was demonstrated to improve the hole transport in PTAA and hole extraction at the PTAA/perovskite interface. Eventually, the fabricated inverted planar PSCs using PTAA HTL with 3 wt% MoO 3 achieved the PCE of 20.06% as compared to that of 17.71% by using pristine PTAA HTL. The present work thus proposes a simple approach to utilize MoO 3 as a dopant to substantially improve the molecular HTLs for high-performance PSCs and other perovskite-based optoelectronics. [ABSTRACT FROM AUTHOR]