Search

Asymmetric tibial insert design is expected to restore normal knee kinematics better than symmetric design. A tri-condylar implant has asymmetric and symmetric tibial inserts with a ball-and-socket joint to replace the post-cam mechanism. The purpose of this study was to compare the knee kinematics of the two designs and to measure tibiofemoral contact stresses, including that of the ball-and-socket joint.Using a computer simulation, the anteroposterior position and axial rotation of the femoral component were simulated during a weight-bearing deep knee bend for six validated models. Contact forces were simultaneously simulated in the medial, lateral, and ball-and-socket compartments. The relative position and the magnitude and direction of each contact force were applied to aforce/displacement control knee simulator. The contact stresses were measured individually using a pressure sensor.The asymmetric tibial insert demonstrated a more posterior position of the femoral component in the lateral compartment during the entire range of motion and greater external rotation of the femoral component, compared to the symmetrical tibial insert. The mean peak contact stress of the medial and lateral compartments was 9 Mpa, with no significant differences between the two designs except at 0°. The contact stress of the ball-and-socket joint was 5 MPa.Asymmetry of the tibial insert shows significant kinematic difference and has little influence on the peak contact stress, which is considerably lower than the yield strength of polyethylene. The asymmetric tibial insert can lead to clinical benefits owing to its kinematic and kinetic properties.

Tunnel position during anterior cruciate ligament (ACL) reconstruction is considered as an important factor to restore normal knee kinematics and to gain better clinical outcomes. It is still unknown where the optimal femoral and tibial tunnel position is located in single-bundle (SB) ACL reconstruction. The purposes of this study were to analyze the knee kinematics with various graft positions and to propose the optimal graft position during SB ACL reconstruction. A musculoskeletal computer simulation was used to analyze knee kinematics. Four attachments on the femoral side (anteromedial [AM], mid, posterolateral [PL], and over-the-top positions) and three attachments on the tibial side (AM, middle, and PL positions) were determined. The middle-bundle attachment was placed at the midpoint of the AM and PL bundle attachments for the femoral and tibial attachments. SB ACL reconstruction models were constructed to combine each of the four femoral attachments with each of three tibial attachments. Kinematic comparison was made among a double-bundle (DB) model and 12 SB reconstruction models during deep knee bend and stair descent activity. The tunnel position of the tibia had greater effect of knee kinematics than that of the femur. AM tibial attachment models showed similar medial and lateral anteroposterior positions to the DB model for both activities. Axial rotation in the AM tibial attachment models was similar to the DB model regardless of the femoral attachment, whereas greater maximum axial rotation was exhibited in the PL tibial attachment models, especially during stair descent activity. AM tibial attachment can represent normal knee kinematics, whereas the PL tibial attachment can induce residual rotational instability during high-demand activities. The AM tibial tunnel is recommended for SB ACL reconstruction.

The purpose of this study was to use the finite element method (FEM) to reproduce fracture lines that reach the lateral tibial plateau during open-wedge high tibial osteotomy (OWHTO) in patients with Type III lateral hinge fracture (LHF). It was hypothesized that the FEM could clarify biomechanical causes of Type III LHF, enabling prevention of adverse complications.This study used the nonlinear FEM to analyze the data of eight knees in eight patients (two males and six females) with Type III LHF among 82 patients who underwent OWHTO, as well as the data of eight individuals with no LHF. To predict the onset of Type III LHF, simulation models were also developed in which posterior osteotomy sufficiency varied from 50% to perfect, the latter defined as osteotomy reaching the hinge point.Real-life instances of Type III LHF caused by insufficient posterior osteotomy were reproduced in all patient-specific FEM models, and these models accurately predicted fracture types and locations. During opening of the osteotomy gap, the fracture line reached the lateral tibial plateau, and extended vertically from the end of the insufficient posterior osteotomy, avoiding the rigid proximal tibiofibular joint. In contrast, sufficient posterior osteotomy resulted in a lack of LHF. Posterior osteotomy extension ≥ 70% of the width of the osteotomy plane was the cut-off value to prevent Type III LHF.Forced opening of insufficient posterior osteotomy was found to be a biomechanical cause of Type III LHF that extended perpendicularly to the lateral tibial plateau, avoiding the proximal tibiofibular joint. The clinical significance of this study is that sufficient posterior osteotomy during OWHTO, defined as at least 70% of the width of the osteotomy plane, can prevent Type III LHF.

Several concepts may be used to restore normal knee kinematics after total knee arthroplasty. One is a kinematically aligned (KA) technique, which restores the native joint line and limb alignment, and the other is the use of a medial pivot knee (MPK) design, with a ball and socket joint in the medial compartment. This study aimed to compare motions, contact forces, and contact stress between mechanically aligned (MA) and KA (medial tilt 3° [KA3] and 5° [KA5]) models in MPK. An MPK design was virtually implanted with MA, KA3, and KA5 in a validated musculoskeletal computer model of a healthy knee, and the simulation of motion and contact forces was implemented. Anteroposterior (AP) positions, mediolateral positions, external rotation angles of the femoral component relative to the tibial insert, and tibiofemoral contact forces were evaluated at different knee flexion angles. Contact stresses on the tibial insert were calculated using finite element analysis. The AP position at the medial compartment was consistent for all models. From 0° to 120°, the femoral component in KA models showed larger posterior movement at the lateral compartment (0.3, 6.8, and 17.7 mm in MA, KA3, and KA5 models, respectively) and larger external rotation (4.2°, 12.0°, and 16.8° in the MA, KA3, and KA5 models, respectively) relative to the tibial component. Concerning the mediolateral position of the femoral component, the KA5 model was positioned more medially. The contact forces at the lateral compartment of all models were larger than those at the medial compartment at >60° of knee flexion. The peak contact stresses on the tibiofemoral joint at 90° and 120° of knee flexion were higher in the KA models. However, the peak contact stresses of the KA models at every flexion angle were

Aims The preventive effects of bisphosphonates on articular cartilage in non-arthritic joints are unclear. This study aimed to investigate the effects of oral bisphosphonates on the rate of joint space narrowing in the non-arthritic hip. Methods We retrospectively reviewed standing whole-leg radiographs from patients who underwent knee arthroplasties from 2012 to 2020 at our institute. Patients with previous hip surgery, Kellgren–Lawrence grade ≥ II hip osteoarthritis, hip dysplasia, or rheumatoid arthritis were excluded. The rate of hip joint space narrowing was measured in 398 patients (796 hips), and the effects of the use of bisphosphonates were examined using the multivariate regression model and the propensity score matching (1:2) model. Results A total of 45 of 398 (11.3%) eligible patients were taking an oral bisphosphonate at the time of knee surgery, with a mean age of 75.8 years (SD 6.2) in bisphosphonate users and 75.7 years (SD 6.8) in non-users. The mean joint space narrowing rate was 0.04 mm/year (SD 0.11) in bisphosphonate users and 0.12 mm/year (SD 0.25) in non-users (p < 0.001). In the multivariate model, age (standardized coefficient = 0.0867, p = 0.016) and the use of a bisphosphonate (standardized coefficient = −0.182, p < 0.001) were associated with the joint space narrowing rate. After successfully matching 43 bisphosphonate users and 86 non-users, the joint narrowing rate was smaller in bisphosphonate users (p < 0.001). Conclusion The use of bisphosphonates is associated with decreased joint degeneration in non-arthritic hips after knee arthroplasty. Bisphosphonates slow joint degeneration, thus maintaining the thickness of joint cartilage in the normal joint or during the early phase of osteoarthritis. Cite this article: Bone Joint Res 2022;11(11):826–834.

This study evaluated the clinical outcomes of medial open-wedge high tibial osteotomy (MOWHTO) and bone marrow lesion (BML) scores and volumes. The hypotheses were that quantitative BML volume is more associated with clinical outcomes of MOWHTO than qualitative BML evaluations, and pre-operative BML volume is associated with the improvement of clinical outcomes.Patients who underwent MOWHTO were retrospectively enrolled. The Knee Injury and Osteoarthritis Outcome Score (KOOS) was recorded before the initial surgery and at plate removal surgery. Using pre-operative short-time inversion recovery magnetic resonance imaging, BMLs were evaluated using three qualitative scores, reflecting the maximum length, proportion, and intensity of BML. For quantification, BMLs of the femur and tibia were separately defined as lesions with a threshold greater than the mean signal intensity plus two standard deviations, using the corresponding lateral condyles as controls. The association between the KOOS scales and BML scores/volume was evaluated using Spearman's correlation coefficient. Multivariate linear regression analyses for post-operative KOOS scales were performed using the tibial BML volume as one of the four independent variables.The final analysis included 40 MOWHTO cases. Two qualitative BML scores correlated only with pre-operative KOOS sports. Femoral and tibial BML volumes were correlated with post-operative KOOS QOL (ρ = 0.40, p = 0.01) and sports (ρ = 0.36, p = 0.02), respectively. Tibial BML volume was significantly correlated with all five delta KOOS scales (ρ = 0.39-0.51, p = 0.01-0.001), however, femoral BML volume was only correlated with delta KOOS QOL (ρ = 0.41, p = 0.01). In multivariate analyses, tibial BML volume was a significant positive predictor for every post-operative KOOS scale, while post-operative % mechanical axis was also a positive significant variable, except post-operative KOOS pain.Tibial BML volume was positively correlated with one post-operative KOOS scale and all delta KOOS scales. A larger pre-operative tibial BML and appropriate alignment correction were associated with a better post-operative KOOS scales. Pre-operative large BML had no negative influence on post-operative clinical outcomes; hence, surgeons need not hesitate to perform MOWHTO in patients with large BMLs in the medial condyles.Retrospective case series, Level IV.

Purpose This study aimed to evaluate the acceptability of 14 days of self-quarantine and the positivity rate of pre-operative severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) polymerase chain reaction (PCR) screening for patients undergoing elective orthopaedic surgery. Methods The self-quarantine programme and pre-operative SARS-CoV-2 PCR screening were initiated for patients who were scheduled for admission later than 7 May 2020 for elective orthopaedic surgery on admission. On the day of admission, the patients declared compliance with self-quarantine regulations. The admission was refused in cases of non-compliance. After admission, the patients underwent SARS-CoV-2 PCR screening. If PCR results were negative, isolation was terminated. If PCR results were positive, the surgery was postponed. If the patients had symptoms suspicious of coronavirus disease (COVID-19) after surgery, the PCR test was repeated. Results Overall, 308 patients (age: 63.2 ± 18.8 years, 197 female and 111 male) were scheduled for elective orthopaedic surgery. Two patients did not agree with the requirements of self-quarantine, and two other procedures were cancelled. No non-compliance was reported; thus, the completion rate of the self-quarantine programme was 304/308 (98.7%). Finally, 304 patients underwent PCR testing, and there were no positive PCR results. After cancellations of four operations due to reasons other than COVID-19, 300 surgical procedures were performed. No patients developed COVID-19 during hospitalisation. Conclusions Although this system is based on trusting the good behaviour of patients, accompanied by PCR screening, we believe that the results showed the efficacy of the system in safely performing orthopaedic surgery during the COVID-19 pandemic.

Treatment of implant-associated orthopedic infections remains challenging, partly because antimicrobial treatment is ineffective after a mature biofilm covers the implant surface. Currently, the relative efficacy of systemic mono- and combination standard-of-care (SOC) antibiotic therapies over the course of mature biofilm formation is unknown. Thus, we assessed the effects of cefazoline (CEZ), gentamicin (GM), and vancomycin, with or without rifampin (RFP), on Staphylococcus aureus biofilm formation during the establishment of implant-associated osteomyelitis in a murine tibia model. Quantitative scanning electron microscopy of the implants harvested on Days 0, 3, and 7 revealed that all treatments except CEZ monotherapy significantly reduced biofilm formation when antibiotics started at Day 0 (0.46- to 0.25-fold; p < 0.05). When antibiotics commenced 3 days after the infection, only GM monotherapy significantly inhibited biofilm growth (0.63-fold; p < 0.05), while all antibiotics inhibited biofilm formation in combination with RFP (0.56- to 0.44-fold; p < 0.05). However, no treatment was effective when antibiotics commenced on Day 7. To confirm these findings, we assessed bacterial load via colony-forming unit and histology. The results showed that GM monotherapy and all combination therapies reduced the colony-forming unit in the implant (0.41- to 0.23-fold; p < 0.05); all treatments except CEZ monotherapy reduced the colony-forming unit and staphylococcus abscess communities in the tibiae (0.40- to 0.10-fold; p < 0.05). Collectively, these findings demonstrate that systemic SOC antibiotics can inhibit biofilm formation within 3 days but not after 7 days of infection. The efficacy of SOC monotherapies, CEZ particularly, is very limited. Thus, combination treatment with RFP may be necessary to inhibit implant-associated osteomyelitis.

Background Bicruciate-retaining total knee arthroplasty (BCR-TKA) was developed to maintain anterior cruciate ligament function and thus reproduce natural knee kinematics postoperatively. Traditional surgical techniques, however, may cause several complications secondary to kinematic conflict and ligament overtension. The objective of this study was to use a computer simulation of symmetric BCR-TKA to evaluate the effects of alternative surgical techniques on knee kinematics and ligaments. Methods A musculoskeletal computer model of a healthy knee was constructed and was used to simulate a BCR model with mechanical alignment (MA). Five adjusted models were investigated, characterized, respectively, by kinematic alignment (KA), two degrees increased tibial slope, two-millimeter distal setting of the tibial component, and an undersized femoral component with either MA or KA. Results All models exhibited a normal femoral position against the tibia at knee extension, with no anterior paradoxical motion during mid-flexion. The healthy knee model showed medial pivot motion and rollback. In contrast, the BCR MA model demonstrated abnormal bi-condylar rollback with excessive tensions of the lateral collateral ligament and posterior cruciate ligament during knee flexion, whereas the undersized femoral model with MA partly reduced both tensions. The BCR KA model retained relatively physiological kinematics and suppressed excessive ligament tensions. However, no adjusted model completely reproduced healthy knee conditions. Conclusions The BCR MA model showed abnormal biomechanics due to kinematic conflict between the retained ligaments and the replaced joint surface. Surgeons using symmetric BCR-TKA should consider using the KA method to achieve sufficient ligament laxity throughout knee flexion.

Musculoskeletal infections (MSKIs) remain a major health burden in orthopaedics. Bacterial toxins are foundational to pathogenesis in MSKI, but poorly understood by the community of providers that care for patients with MSKI, inducing an international group of microbiologists, infectious diseases specialists, orthopaedic surgeons and biofilm scientists to review the literature in this field to identify key topics and compile the current knowledge on the role of toxins in MSKI, with the goal of illuminating potential impact on biofilm formation and dispersal as well as therapeutic strategies. The group concluded that further research is needed to maximize our understanding of the effect of toxins on MSKIs, including: (i) further research to identify the roles of bacterial toxins in MSKIs, (ii) establish the understanding of the importance of environmental and host factors and in vivo expression of toxins throughout the course of an infection, (iii) establish the principles of drug-ability of anti-toxins as antimicrobial agents in MSKIs, (iv) have well-defined metrics of success for anti-toxins as anti-infective drugs, (v) design a cocktail of anti-toxins against specific pathogens to (a) inhibit biofilm formation and (b) inhibit toxin release. The applicability of anti-toxins as potential antimicrobials in the era of rising antibiotic resistance could meet the needs of day-to-day clinicians.

Medial release during total knee arthroplasty (TKA) is used to correct ligament imbalance in knees with varus deformity. However, questions remain on whether residual ligament imbalance would be related to inferior clinical results. The purposes of the present study were to measure the intraoperative joint gap and to evaluate the effect of intraoperative soft tissue condition on the new Knee Society Score (KSS 2011) at 2-year follow-up, without the maneuver of additional medial release to correct the asymmetrical gap balance. Varus–valgus gap angle and joint gap were measured using a tensor device without medial release for 100 knees with preoperative varus deformity. The knees were categorized according to the varus–valgus gap angle and the laxity. The preoperative and postoperative clinical outcomes using KSS 2011 were compared between the groups. The average varus–valgus angles had a residual imbalance of 2.8° varus and 1.3° varus in extension and flexion, respectively. In comparison, according to varus–valgus joint gap angle and knee laxity in extension and flexion, no significant differences were found in postoperative range of motion and subscale of KSS 2011 among the groups. Intraoperative asymmetrical joint gap and physiological laxity do not affect early clinical results after TKA. III.

The primary aim of this study was to evaluate the 3-dimensional morphology of the proximal tibia around the osteotomy plane in open-wedge high tibial osteotomy, focusing on the posterolateral (PL) and posteromedial (PM) tibial condyles, and to clarify the changes in morphologic parameters due to differences in patient characteristics and hinge position. The secondary aim was to examine whether morphologic features were associated with insufficient osteotomy, which increases the risk of lateral hinge fracture (LHF).The PL and PM anteroposterior distance, asymmetry ratio, and discrepancy between PL and PM distances along the tibial osteotomy plane were measured. We investigated changes in the parameters due to differences in patient characteristics and hinge position. Osteotomy configurations and LHFs were evaluated using postoperative computed tomography scans.The 3-dimensional preoperative plans of 117 knees (male, 41 knees; female, 76 knees) were evaluated. PL distances were larger than PM distances in almost all cases. The average asymmetry ratio was 1.35, and the standard deviation was 0.22. Higher hinge position was associated with a larger asymmetry ratio and discrepancy (P.001). The asymmetry ratio and discrepancy were independently positively correlated with male sex (P = .002 and P = .001, respectively) and gentle posterior tibial slope (P.001 and P.001, respectively). Osteotomies with type III LHFs showed lower osteotomy sufficiency than osteotomies without LHFs (P.001).PL tibial condyle protrusion was more pronounced in male patients and those with a high hinge position, and may result in insufficient PL osteotomy, which is a risk factor for type III LHF during open-wedge high tibial osteotomy. The optimal hinge position was located approximately 15 mm and 20 mm distal to the lateral tibial plateau in female and male patients, respectively.IV: retrospective case series.

To determine the magnetic resonance imaging (MRI) findings after mosaicplasty (MOS) for knee subchondral insufficiency fracture (SIFK), and to analyze the relationship between MRI findings and clinical outcomes.We retrospectively reviewed the cases of consecutive patients who underwent MOS for SIFK with/without high tibial osteotomy (HTO) between January 1998 and December 2015. The MRI findings at 12 months after the surgery were assessed by the modified magnetic resonance observation of cartilage repair tissue (MOCART) score to determine the degree of bone marrow edema (BME), plug union, and plug necrosis. The clinical outcomes were assessed by Lysholm score to clarify the minimal clinically important difference (MCID) and patient acceptable symptom state analysis.In total, 58 patients (17 men and 41 women) were enrolled in this study. Among them, 30 knees were treated by MOS alone and 28 knees were treated by MOS with HTO. The MOCART scores of patients who received MOS alone were significantly lower in BME score (P = .0060), plug union score (P = .0216), and in plug necrosis score (P = .0326) than patients who received MOS with HTO. BME lesion was less likely to persist among elderly (odds ratio 1.20, P = .0248) and female (OR 41.8, P = .0118) patients. The MCID of Lysholm score was 6.6 in MOS alone and 8.4 in MOS with HTO cases, but there were no significant association between MRI findings and the postoperative Lysholm score.The MOS with HTO cases had better MOCART scores with less BME, better plug union, and less plug necrosis compared with MOS alone cases. Female and older patients had better resolution of BME, but there was no significant correlation between MRI findings and the postoperative Lysholm score. All cases in both groups showed improvement of Lysholm score exceeding MCID; thus, MOS may be effective as a joint preserving surgery for SIFK.Level IV, clinical case series.

The correlation between static and dynamic mediolateral (ML) tilts of the joint line in the coronal plane remains unknown after total knee arthroplasty (TKA). The purpose was to evaluate the ML tilt as measured by two-dimensional to three-dimensional registration during stair ascent in TKA patients, and to examine the correlation between the dynamic ML tilt and radiographic measurements of static indices. Thirty-two knees that underwent TKA using the mechanical alignment method were included. Continuous sagittal fluoroscopy was taken from before initial contact (IC) until after the toe-off (TO) phase during the stair ascent. The ML tilt of the tibial component relative to the ground was analyzed in terms of dynamic alignment using image-matching techniques, whereas static alignment was measured using standing long-leg radiographs. The correlation between static and dynamic ML tilts was evaluated. In the fluoroscopic analysis, the joint line was neutral (0.0 degree, standard deviation [SD] = 3.4 degrees) around IC phases, then was tilted valgus (5.5° valgus, SD = 2.6 degrees) in the mid-stance (MS) phase. After the TO phase, the joint line became almost neutral (0.4 degrees valgus, SD = 3.1 degrees). The dynamic ML tilt was significantly more varus during the IC phase and significantly more valgus in MS and TO phases than the static ML tilt (1.4 degrees valgus, SD = 2.0 degrees). No correlation was found between static and dynamic ML tilts in weight-bearing phases. During stair ascent, the static tilt had no correlation with the dynamic tilt in weight-bearing phases despite being in the same range. Static lower limb alignment does not reflect coronal alignment during motion. Further research should be conducted to determine whether the horizontal dynamic ML tilt can improve long-term durability and clinical outcomes after TKA.

PURPOSE This study evaluated whether patients with particular lower limb morphological factors have femoral and tibial component malpositioning during mechanically aligned total knee arthroplasty (TKA) and lower postoperative satisfaction. METHODS This study included 146 knees in 117 Asian patients undergoing TKA for medial osteoarthritis. Preoperative bony morphological factors such as the angle between the femoral mechanical and anatomical axes (MA-AA angle), angle between the anatomical axes of the proximal and distal femur (lateral bowing femoral angle, LBFA), mechanical lateral distal femoral angle, medial proximal tibial angle, and % anatomical axis of the tibia were evaluated, as well as preoperative and 1-year postoperative 2011 Knee Society scores (KSSs). RESULTS MA-AA angle and LBFA were significantly larger in knees with varus femoral component alignment versus neutral alignment. Preoperative MA-AA angle was underestimated in patients with larger MA-AA angle or LBFA, especially by inexperienced surgeons. Tibial morphological factors did not affect tibial component alignment. Changes in 2011 KSSs were similar among groups by lower limb alignment or femoral and tibial component alignment. CONCLUSION Femoral bowing affects varus femoral component alignment by obscuring preoperative planning, but it had little impact on patient satisfaction when mechanical alignment is targeted during TKA.

Background The new Knee Society Score (2011KSS) has been used to evaluate post-operative outcomes after total knee arthroplasty (TKA). However, there is no minimum clinically important difference (MCID) for 2011KSS. The purpose of this study is to define MCID of 2011KSS after TKA. Methods Patients who underwent primary TKA for primary knee osteoarthritis between April 2012 and December 2016 were included in the study. The Japanese version of 2011KSS and original Knee Society Score (OKSS) were recorded preoperatively and at one-year postoperatively. With improvement in pain score of OKSS as an anchor, an anchor-based approach was used to identify the MCID of 2011KSS. The improvement in pain of OKSS was classified into 5 categories. The MCID was determined using a linear regression analysis of delta 2011KSS against improvement in the category of pain in OKSS. The MCID for 2011KSS expectation was not calculated because the items of pre- and post-operative questionnaires were different. Results Five hundred and twenty-two cases were enrolled (age: 74.8 ± 7.3 years, female: 80.0%). After 1-year follow-up, 344 TKAs were finally included (age: 74.6 ± 7.1 years, female: 77.9%). Linear regression analyses showed that MCID for 2011KSS was 1.9 (95% confidential interval (CI): 1.3–2.5) in symptom, 2.2 (95%CI: 1.4–2.9) in satisfaction, and 4.1 (95%CI: 2.5–5.7) in functional activities. Conclusions MCID for 2011KSS was successfully calculated. These MCID values make the 2011KSS a more efficient tool for evaluating the physical activities of the populations of patients undergoing TKA. These MCID values can also be used to calculate sample size to evaluate the power of a study in designing clinical studies.

The purpose of this study was to determine the ideal coronal alignment under dynamic conditions after open-wedge high tibial osteotomy (OWHTO). It was hypothesised that, although the classical target alignment was based on experimental evidence, it would demonstrate biomechanical validity. Musculoskeletal computer models were analysed with various degrees of coronal correction in OWHTO during gait and squat, specifically with the mechanical axis passing through points at 40%, 50%, 60%, 62.5%, 70%, and 80% of the tibial plateau from the medial edge, defined as the weight-bearing line percentage (WBL%). The peak load on the lateral tibiofemoral (TF) joint, the medial collateral ligament (MCL), and anterior cruciate ligament (ACL) tensions, and knee kinematics with or without increased posterior tibial slope (PTS) were evaluated. The classical alignment with WBL62.5% achieved sufficient load on the lateral TF joint and maintained normal knee kinematics after OWHTO. However, over-correction with WBL80% caused an excessive lateral load and non-physiological kinematics. Increased WBL% resulted in increased MCL tension due to lateral femoral movement against the tibia. With WBL80%, abnormal contact between the medial femoral condyle and the medial intercondylar eminence of the tibia occurred at knee extension. The screw-home movement around knee extension and the TF rotational angle during flexion were reduced as WBL% increased. Increased PTS was associated with increased ACL tension and decreased TF rotation angle because of ligamentous imbalance. The classical target alignment demonstrated validity in OWHTO, and over-correction should be avoided as it negatively impacts clinical outcome. IV.

Purpose: Despite the long history of drain use in total knee arthroplasty (TKA), no drain has been gaining popularity. The purpose of this study was to investigate whether drainage is related to the length of hospital stay. Materials and Methods: A total of 166 consecutive unilateral TKAs performed on 135 patients with osteoarthritis were retrospectively reviewed. Closed suction drainage was used in 111 cases (67%). Length of hospital stay after surgery was recorded, and a multivariate linear regression analysis was performed to evaluate various variables (patient factors, surgical factors, and post-surgical factors) and to investigate whether drainage was an independent variable. Results: Hospital stay was shorter in no drain cases (21.7±4.8 days) than in drain cases (24.2±3.7 days, p

Lower limb malrotations can be observed in long leg radiographs, affecting the measurement of the angle between the mechanical and anatomical axes. The purposes were to analyze the effect of limb rotation and to evaluate the accuracy of the corrected angle between the mechanical and anatomical axes based on the patellar ML position.The hypothesis was that the correction of the angle between the mechanical and anatomical axes according to the patellar ML position can reduce the error from the angle in the true AP view in most of the knees.A total of 100 consecutive knees with varus deformity undergoing primary total knee arthroplasty were included. Computed tomography images were digitally reconstructed in the neutral position, and internally and externally rotated at 10° and 20°, respectively. The patellar ML position relative to the medial (0%) and lateral (100%) epicondyles and the angle between the mechanical and anatomical axes of the femur were measured. The corrected angle between the mechanical and anatomical axes was calculated using the averaged translational ratio.In the neutral position, the patellar center position was 56.1% (standard deviation [SD]=4.7%), which was 31.4% (SD=7.2%) and 80.2% (SD=5.4%) in the 20° internal and external rotation, respectively. The angle between the mechanical and anatomical axes was 2.6° (SD=2.0°) and 8.1° (SD=2.1°) in the 20° internal and external rotation, respectively. On average, if the patellar center shifted 10%, the change of the angle between the mechanical and anatomical axes of the femur was 1.13°. Applying the corrected angle, a discrepancy from the neutral position decreased.The method to correct the angle between the mechanical and anatomical axes according to the patellar ML position can be used to reduce the measurement error for preoperative planning using a long leg radiograph.III.

Background The in vivo kinematic benefit of an asymmetrical polyethylene insert is still unknown in comparison with that of a symmetrical insert with the same femoral component design. The purpose of this study was to analyze the kinematic differences between symmetrical and asymmetrical polyethylene inserts and to detect the kinematic benefit in the asymmetrical polyethylene insert. The hypotheses are that greater axial rotation and more posterior rollback are observed in the asymmetrical polyethylene insert. Methods The patients were randomly allocated to the following two groups: total knee arthroplasty with a symmetrical insert and with an asymmetrical insert. In vivo knee kinematics was analyzed in asymmetrical (17 knees) and symmetrical (16 knees) inserts using an image matching technique. The symmetrical polyethylene insert had the same geometry on both sides, whereas the asymmetrical polyethylene insert had a flat surface on the postero-lateral side. The anterior/posterior position and axial rotation were compared between the two polyethylene inserts. Results The femoral component was significantly positioned posteriorly at 70° (p = 0.016) and 80° (p = 0.040) of knee flexion and externally rotated at 80° of knee flexion (p = 0.040) in the asymmetrical polyethylene insert as compared to the position of the symmetrical polyethylene insert. Femoral rollback and axial rotation from full extension to maximum flexion were greater in the asymmetrical polyethylene insert, although the difference was not significant. Conclusions In the asymmetrical polyethylene insert, slight kinematic benefit with greater axial rotation and more posterior rollback was observed in comparison with the symmetrical polyethylene insert. Further research should be required whether the kinematic benefit of an asymmetrical polyethylene insert will lead to better patient satisfaction and function.

Background: The treatment of a meniscus-deficient knee is challenging, especially when patients are young and active and are not favorable candidates for prosthetic joint replacement. Hypothesis: We hypothesized that osteochondral autologous transplant (OAT) alone can be considered a salvage treatment for patients with cartilage damage of the lateral compartment of the knee, even with lateral meniscal deficiency, if the knee alignment is close to neutral. Study Design: Case series; Level of evidence, 4. Methods: Patients with lateral meniscal deficiency, whose femorotibial angle was 170° to 180° and who underwent OAT on the lateral compartment of the knee without concomitant realignment osteotomy, were retrospectively included in this study. The International Knee Documentation Committee (IKDC) subjective score and the Japanese Orthopaedic Association score for knee osteoarthritis (JOA knee score) were recorded. The International Cartilage Repair Society (ICRS) cartilage repair assessment was used to evaluate the repaired cartilage at second-look arthroscopy. Results: The study included 10 patients (mean ± SD age, 31.7 ± 19.7 years; 3 men and 7 women) who had ICRS grade 4 cartilage lesions (mean size, 3.5 ± 1.7 cm2); the mean follow-up was 73.8 ± 42.5 months. From preoperative assessment to final follow-up, the mean IKDC subjective score improved significantly from 53.5 ± 10.0 to 85.4 ± 10.1, and the mean JOA knee score improved significantly from 81.0 ± 8.4 to 95.6 ± 5.3 ( P = .004 for both). One patient with a femorotibial angle of 170° underwent revision distal femoral osteotomy owing to prolonged symptoms and progression of the valgus deformity, and 2 other patients with femorotibial angles of 170° and 171° also exhibited progression of valgus malalignment or low clinical scores postoperatively. Patients with a favorable femorotibial angle (174°-178°) exhibited relieved symptoms and preservation of femorotibial angle alignment within 1° of change at follow-up. At second-look arthroscopy (n = 8 patients), 6 patients had an ICRS score of nearly normal or normal. Conclusion: In the study patients, for which a meniscal allograft was unavailable, the OAT procedure was able to relieve the symptoms associated with cartilage lesions, even with lateral meniscal deficiency, when the femorotibial angle alignment was close to neutral.

Introduction The tension of anterior cruciate ligament (ACL) graft has an important role in antero-posterior (AP) and rotational stability of the knee. The purposes of this study were to analyze the kinematics and kinetics of normal knee models with loose and tight ACL tension, and to evaluate the effect of the tension of ACL on knee kinematics and kinetics. Materials and methods Slack and tight ACL models were constructed in a musculoskeletal computer simulation. The effect of ACL tension on kinematics, and femorotibial contact force during various activities was analyzed. Results During stair descent activity in the slack ACL models, the lateral femoral condyles were positioned posterior, and more external rotation of the femur was observed in comparison with the normal model. The contact forces at the lateral compartment in the tight models increased during all activities, and the tension of the medial collateral ligament (MCL) in the slack models increased during the stair descent activity, compared with the normal knee model. Conclusion AP and rotational instability and excessive MCL tension were observed in the ACL slack knees especially during stair descent movement, whereas the tibiofemoral contact force of the lateral compartment increased in the tight ACL knees.

AimsThis study aimed to evaluate the association between the sagittal alignment of the femoral component in total knee arthroplasty (TKA) and new Knee Society Score (2011KSS), under the hypothesis that outliers such as the excessive extended or flexed femoral component were related to worse clinical outcomes.MethodsA group of 156 knees (134 F:22 M) in 133 patients with a mean age 75.8 years (SD 6.4) who underwent TKA with the cruciate-substituting Bi-Surface Knee prosthesis were retrospectively enrolled. On lateral radiographs, γ angle (the angle between the distal femoral axis and the line perpendicular to the distal rear surface of the femoral component) was measured, and the patients were divided into four groups according to the γ angle. The 2011KSSs among groups were compared using the Kruskal-Wallis test. A secondary regression analysis was used to investigate the association between the 2011KSS and γ angle.ResultsAccording to the mean and SD of γ angle (γ, 4.0 SD 3.0°), four groups (Extended or minor flexed group, −0.5° ≤ γ < 2.5° (n = 54)), Mild flexed group (2.5° ≤ γ < 5.5° (n = 63)), Moderate flexed group (5.5° ≤ γ < 8.5° (n = 26)), and Excessive flexed group (8.5° ≤ γ (n = 13)) were defined. The Excessive flexed group showed worse 2011KSSs in all subdomains (Symptoms, Satisfaction, Expectations, and Functional activities) than the Mild flexed group. Secondary regression showed a convex upward function, and the scores were highest at γ = 3.0°, 4.0°, and 3.0° in Satisfaction, Expectations, and Functional activities, respectively.ConclusionThe groups with a sagittal alignment of the femoral component > 8.5° showed inferior clinical outcomes in 2011KSSs. Secondary regression analyses showed that mild flexion of the femoral component was associated with the highest score. When implanting the Bi-Surface Knee prosthesis surgeons should pay careful attention to avoiding flexing the femoral component extensively during TKA. Our findings may be applicable to other implant designs. Cite this article: Bone Joint J 2020;102-B(6 Supple A):36–42.

Tibiofemoral joint instability reduces patient satisfaction after total knee arthroplasty (TKA). However, surgeons sometimes encounter excessive medial joint laxity without medial over-release on the tibial side. It was hypothesized that over-resection of the posteromedial femoral condyle can injure the medial stabilizers, especially the posterior oblique ligament (POL) at its femoral attachments. Thirteen fixed cadaveric knees were exposed, and 3 anatomical points were identified: the posterior edge and midpoint of the POL femoral attachment, and the posterior edge of the superficial medial collateral ligament (sMCL) femoral attachment. The distance from the surface of the posteromedial femoral condyle to each point was measured. Correlations between each point and the anterior–posterior or medial–lateral dimensions of the distal femur were also calculated. The average distances to the posterior edge and midpoint of the POL femoral attachment and the posterior edge of the sMCL femoral attachment were 13.7 mm (9.0–18.4), 17.9 mm (11.5–22.6), and 22.7 mm (14.7–29.4), respectively. There were moderate correlations between the distance to each point and the anterior–posterior or medial–lateral dimensions of the distal femur. The minimal distance from the surface of the posteromedial condyle to the POL posterior edge was 9.0 mm. Over-resection of the posteromedial femoral condyle, even with a general TKA femoral component, might injure the POL at its femoral attachments, especially in patients with small distal femurs, while the sMCL is rarely damaged. Level IV.

This study aimed to examine the effects of an episode of in vivo cyclic loading on rat knee articular cartilage (AC) under medium-term observation, while also investigating relevant factors associated with the progression of post-traumatic osteoarthritis (PTOA). Twelve-week-old Wistar rats underwent one episode comprising 60 cycles of 20 N or 50 N dynamic compression on the right knee joint. Spatiotemporal changes in the AC after loading were evaluated using histology and immunohistochemistry at 3 days and 1, 2, 4, and 8 weeks after loading (n = 6 for each condition). Chondrocyte vitality was assessed at 1, 3, 6, and 12 hours after loading (n = 2 for each condition). A localized AC lesion on the lateral femoral condyle was confirmed in all subjects. The surface and intermediate cartilage in the affected area degenerated after loading, but the calcified cartilage remained intact. Expression of type II collagen in the lesion cartilage was upregulated after loading, whereas the superficial lubricin layer was eroded in response to cyclic compression. However, the distribution of superficial lubricin gradually recovered to the normal level 4 weeks after loading-induced injury. We confirmed that 60 repetitions of cyclic loading exceeding 20 N could result in cartilage damage in the rat knee. Endogenous repairs in well-structured joints work well to rebuild protective layers on the lesion cartilage surface, which may be the latent factor delaying the progression of PTOA.

Antibiotic-loaded bone cement (ALBC) is broadly used to treat orthopaedic infections based on the rationale that high-dose local delivery is essential to eradicate biofilm-associated bacteria. However, ALBC formulations are empirically based on drug susceptibility from routine laboratory testing, which is known to have limited clinical relevance for biofilms. There are also dosing concerns with nonstandardized, surgeon-directed, hand-mixed formulations, which have unknown release kinetics. On the basis of our knowledge of in vivo biofilms, pathogen virulence, safety issues with nonstandardized ALBC formulations, and questions about the cost-effectiveness of ALBC, there is a need to evaluate the evidence for this clinical practice. To this end, thought leaders in the field of musculoskeletal infection (MSKI) met on 1 August 2019 to review and debate published and anecdotal information, which highlighted four major concerns about current ALBC use: (a) substantial lack of level 1 evidence to demonstrate efficacy; (b) ALBC formulations become subtherapeutic following early release, which risks induction of antibiotic resistance, and exacerbated infection from microbial colonization of the carrier; (c) the absence of standardized formulation protocols, and Food and Drug Administration-approved high-dose ALBC products to use following resection in MSKI treatment; and (d) absence of a validated assay to determine the minimum biofilm eradication concentration to predict ALBC efficacy against patient specific micro-organisms. Here, we describe these concerns in detail, and propose areas in need of research.

One of the causes of aseptic loosening is marked tibial bone resorption (TR) at the tibial bone–component interface after total knee arthroplasty (TKA). It was hypothesized that insufficient coverage of the tibial component and improper cementing technique would cause increased TR after cemented TKA. One hundred thirty-four primary TKAs in 107 patients with varus osteoarthritis were included in this study. The relationships between the TRs at 2 years after TKA and the tibial component underhang (TUH), the thickness of the cement mantle around the keel, and clinical parameters were evaluated. The widths of TRs on anteroposterior radiographs were significantly larger on the medial side than on the lateral side (p = 0.001), whereas the difference between the anterior and posterior sides on lateral radiographs was relatively small. Multiple regression analyses showed that medial TR was positively related to medial TUH (p = 0.006), and lateral TR was positively related to a thicker distal cement mantle (p = 0.027). On the lateral view, stepwise selection indicated that postoperative knee flexion angle was the most significant risk factor (p = 0.005) for anterior TR, and posterior TUH was the strongest predictor (p = 0.001) of posterior TR. To avert postoperative progressive TR, surgeons should perfectly fit a suitably sized tibial component to the medial edge of the tibia. Also, care should be taken to avoid an excessive cement mantle at the distal portion of the keel during TKA. IV.

Total knee arthroplasty (TKA) for valgus knee osteoarthritis is challenging. Although overcorrection in TKA for valgus knee osteoarthritis is recommended, supportive data based on biomechanics have rarely been reported. The purpose of this study was to elucidate whether coronal rotation of the femoral compartment causes abnormal kinematics with or without medial looseness. Multi- and single-radius posterior-stabilised TKA implants were utilised in a computer simulation. A total of 4 mm of slack were provided in the medial collateral ligament (MCL) with varus or valgus position of the femoral component to simulate the context of valgus knee osteoarthritis. Kinematics during gait and squatting activities were evaluated in each condition. During squatting, medial looseness and valgus replacement caused anterior translation of the medial femoral component in mid-flexion in the multi-radius implant. In the worst condition (7° valgus replacement with MCL looseness), there was rapid anterior translation in the multi-radius implant, and moderate anterior translation in the single-radius implant. Although medial looseness alone did not cause abnormal kinematics during gait, the worst condition exhibited an anterior translation to 4.9 mm in the multi-radius implant. This worst condition also exhibited a marked lift-off of 8.0 and 2.9 mm in the multi- and single-radius implants, respectively. Varus position caused little abnormal kinematics even with MCL looseness. Valgus, not varus position of the femoral component caused abnormal kinematics with MCL looseness. To avoid valgus position, the safety target angle of femoral component would be slight varus rather than neutral in valgus knee OA.

Background Instability is a common failure mode after total knee arthroplasty. There have been only a few methods to quantify anterior translation with fixed forces applied during surgery. The purpose of the study was to measure the anterior translation with a new device and to analyze the relationships between the amount of anterior translation and the joint gaps. Methods Fifty knees with medial osteoarthritis underwent surgery using a posterior-stabilized implant. During surgery, measurement of anterior translation was performed at 90° of knee flexion with a trial implant, applying a traction force of 70 N. The joint gap was measured using a tensor device, applying a distraction force of 178 N in flexion. The Pearson correlation coefficient was calculated between anterior translation and joint gaps and laxity. Results On average, anterior translation during surgery was 8.5 mm (standard deviation [SD] = 3.6 mm). Medial gap (correlation coefficient [r] = 0.30), medial laxity (r = 0.33), and center laxity (r = 0.29) had a positive correlation with anterior translation, and anterior translation increased with larger joint gap or greater laxity. Conclusion Anterior translation was measured with a new device by applying the anterior force to the tibia, and the correlations between anterior translation and joint gap and laxity were analyzed. A larger medial gap and greater medial laxity were correlated with greater anterior translation, which could cause symptomatic feelings of instability. Surgeons should pay attention to the tension of medial structures in flexion and avoid excessive medial release during surgery.

The relationship between postoperative tibiofemoral ligament balance and patient satisfaction in total knee arthroplasty (TKA) has been explored previously. However, the optimal intraoperative medial–lateral ligament balance during knee flexion in terms of postoperative patient satisfaction remains unknown. We evaluated the effect of intraoperative flexion instability on patient satisfaction after TKA. This study consisted of 46 knees with varus osteoarthritis undergoing TKA. Medial–lateral component gaps at 0° knee extension and 90° flexion were measured intraoperatively using a knee balancer. Differences in postoperative patient outcomes at 3 weeks and 1 year were compared between medially tight knees in 90° flexion with a medial component gap of

Methicillin-resistant Staphylococcus aureus (MRSA) reinfection following revision surgery remains a major orthopaedic problem. Toward the development of immunotherapy with anti-glucosaminidase monoclonal antibodies (anti-Gmd), we aimed to: (i) develop a murine 1-stage exchange model of bioluminescent MRSA (USA300LAC::lux) contaminated femoral implants; and (ii) utilize this model to demonstrate the synergistic effects of combination vancomycin and anti-Gmd therapy on reinfection and bone healing. Following an infection surgery, the original plate and two screws were removed on day 7, and exchanged with sterile implants. Mice were randomized to five groups: (i) no infection control; (ii) infected placebo; (iii) anti-Gmd; (iv) vancomycin; and (v) combination therapy. Bioluminescent imaging (BLI) was performed on days 0, 1, 3, 5, 7, 8, 10, 12, and 14. Mice were euthanized on day 14 (day 7 post-revision), and efficacy was assessed via colony forming units (CFU) on explanted hardware, micro-CT, and histology. As monotherapies, anti-Gmd inhibited Staphylococcus abscess communities, and vancomycin reduced CFU on the implants. However, only combination therapy prevented increased BLI post-revision surgery, with a significant 6.5-fold reduction on day 10 (p < 0.05 vs. placebo), and achieved sterile implant levels by day 12. Synergistic effects were also apparent from reduced osteolysis and increased new bone formation around the screws only observed following combination therapy. Taken together, we find that: (i) this murine femoral plate 1-stage revision model can efficiently evaluate therapies to prevent reinfection; and (ii) immunotherapy plays a distinct role from antibiotics to reduce reinfection following revision surgery, such that synergy to achieve osseointegration is possible. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1590-1598, 2018.

The aims of this study were to investigate the influence of subchondral bone fragility (SBF) on the progression of the knee osteoarthritis by using a novel rat model, and to examine the preventive effect of parathyroid hormone (PTH) on cartilage degeneration. First, 40 rats were assigned to the following four groups: Sham, SBF, Medial meniscal tear (MMT), and MMT + SBF groups. In SBF and MMT + SBF groups, we induced SBF by microdrilling the subchondral bone. Second, 10 additional rats were randomly assigned to the following two groups: MMT + SBF + saline and MMT + SBF + PTH groups. Osteoarthritic changes in the articular cartilage and subchondral bone were evaluated using safranin-O/fast green staining, matrix metalloproteinase-13 (MMP-13), and type X collagen immunohistochemistry, toluidine blue staining, and micro-CT scanning. The combination of SBF and meniscal tear increased the number of mast cells in the subchondral bone, and led to the abnormal subchondral bone microarchitecture, such as abnormally decreased trabecular number and increased trabecular thickness, compared with meniscal tear alone. Moreover, SBF with meniscal tear enhanced articular cartilage degeneration and increased the expression of MMP-13 and type X collagen, compared with meniscal tear alone. The administration of PTH decreased the number of mast cells in the subchondral bone and improved the microstructural parameters of the subchondral bone, and delayed the progression of articular cartilage degeneration. These results suggest that SBF is one of the factors underlying the osteoarthritis development, especially in knees with traumatic osteoarthritis, and that the administration of PTH is a potential therapeutic treatment for preventing OA progression. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1959-1968, 2018.

Summary Objective To examine the clinical impact of coexisting lateral osteoarthritis (OA) in knees with mild medial OA. Design In patients with Kellgren/Lawrence (K/L) grade 2 OA in the medial compartment ( n = 100; age: 56–89 years; 80.0% female), anteroposterior knee radiography was used to assess the presence of lateral OA, using grading systems from the Osteoarthritis Research Society International (OARSI) atlas and the K/L classification. The Japanese Knee Osteoarthritis Measure (JKOM), knee range of motion (ROM), and performance-based functional measures (10 m walk, timed up and go and five repetition chair stand maneuvers) were evaluated. The outcomes were compared between patients with and without lateral OA using an analysis of covariance (ANCOVA) or nonparametric rank ANCOVA. Furthermore, ordinal logistic regression analysis was performed, with responses on individual JKOM pain questionnaires as the outcomes and lateral OA as the predictor. Results Knees with coexisting lateral OA had a significantly worse score of JKOM pain question compared with those without, after adjusting for covariates. The presence of lateral OA was significantly associated with knee pain while ascending/descending stairs and standing. These results were consistent between different definitions of the K/L and OARSI grading systems. The knee ROM and performance-based functional measures were not significantly different between patients with and without lateral OA. Conclusion Knees with concomitant lateral and mild medial OA may be more symptomatic compared to those without lateral OA. These findings might help to define a clinically distinct subgroup based on a simple radiographic finding in mild knee OA.

Although Staphylococcus aureus osteomyelitis is considered to be incurable, the major bacterial reservoir in live cortical bone has remained unknown. In addition to biofilm bacteria on necrotic tissue and implants, studies have implicated intracellular infection of osteoblasts and osteocytes as a mechanism of chronic osteomyelitis. Thus, we performed the first systematic transmission electron microscopy (TEM) studies to formally define major reservoirs of S. aureus in chronically infected mouse (Balb/c J) long bone tissue. Although rare, evidence of colonized osteoblasts was found. In contrast, we readily observed S. aureus within canaliculi of live cortical bone, which existed as chains of individual cocci and submicron rod-shaped bacteria leading to biofilm formation in osteocyte lacunae. As these observations do not conform to the expectations of S. aureus as non-motile cocci 1.0 to 1.5 μm in diameter, we also performed immunoelectron microscopy (IEM) following in vivo BrdU labeling to assess the role of bacterial proliferation in canalicular invasion. The results suggest that the deformed bacteria: (1) enter canaliculi via asymmetric binary fission; and (2) migrate toward osteocyte lacunae via proliferation at the leading edge. Additional in vitro studies confirmed S. aureus migration through a 0.5-μm porous membrane. Collectively, these findings define a novel mechanism of bone infection, and provide possible new insight as to why S. aureus implant-related infections of bone tissue are so challenging to treat. © 2016 American Society for Bone and Mineral Research.

Despite its presence in orthopaedic infections, Staphylococcus epidermidis's ability to directly induce inflammation and bone destruction is unknown. Thus, we compared a clinical strain of methicillin-resistant biofilm-producing S. epidermidis (RP62A) to a highly virulent and osteolytic strain of methicillin-resistant Staphylococcus aureus (USA300) in an established murine implant-associated osteomyelitis model. Bacterial burden was assessed by colony forming units (CFUs), tissue damage was assessed by histology and micro-computed tomography, biofilm was assessed by scanning electron microscopy (SEM), host gene expression was assessed by quantitative polymerase chain reaction, and osseous integration was assessed via biomechanical push-out test. While CFUs were recovered from RP62A-contaminated implants and surrounding tissues after 14 days, the bacterial burden was significantly less than USA300-infected tibiae (p < 0.001). In addition, RP62A failed to produce any of the gross pathologies induced by USA300 (osteolysis, reactive bone formation, Staphylococcus abscess communities, marrow necrosis, and biofilm). However, fibrous tissue was present at the implant-host interface, and rigorous SEM confirmed the rare presence of cocci on RP62A-contaminated implants. Gene expression studies revealed that IL-1β, IL-6, RANKL, and TLR-2 mRNA levels in RP62A-infected bone were increased versus Sterile controls. Ex vivo push-out testing showed that RP62A-infected implants required significantly less force compared with the Sterile group (7.5 ± 3.4 vs. 17.3 ± 4.1 N; p < 0.001), but required 10-fold greater force than USA300-infected implants (0.7 ± 0.3 N; p < 0.001). Taken together, these findings demonstrate that S. epidermidis is a commensal pathogen whose mechanisms to inhibit osseous integration are limited to minimal biofilm formation on the implant, and low-grade inflammation. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 38:852-860, 2020.

Tibial tubercle-trochlear groove (TT-TG) distance is associated with a greater risk of recurrent patellar dislocation in young, active patients. However, the effect of TT-TG distance after total knee arthroplasty (TKA) has not been investigated. The purpose is to analyze the effect of TT-TG distance and component rotation on patellar tilt and patellar shift after TKA.After TKA, axial computed tomography scans and axial radiograph were taken in 115 consecutive knees. TT-TG distance was measured between the most anterior point of the tibial tuberosity and the deepest point of the femoral component relative to a line connecting the anterior condyles. Femoral and tibial component rotation was measured relative to the femoral and tibial rotational axis, respectively. Pearson correlation coefficients were calculated.TT-TG distance had a significant correlation with patellar tilt in extension (R = 0.220, P = .018), patellar tilt in flexion (R = 0.438, P.001), and patellar shift (R = 0.330, P.001). Tibial component rotation had a significant correlation with patellar tilt in flexion (R = -0.251, P = .007) and patellar shift (R = -0.360, P.001). Femoral component rotation had no significant correlations. Tibial component rotation had a significant correlation with TT-TG distance (R = -0.573, P.001), whereas femoral component rotation had no correlation (P = .192).TT-TG distance had a significant correlation with patellar tilt and patellar shift. Surgeons need to understand the factors affecting TT-TG distance and to pay attention to avoiding excessive TT-TG distance after TKA.

ObjectivesUnicompartmental knee arthroplasty (UKA) is one surgical option for treating symptomatic medial osteoarthritis. Clinical studies have shown the functional benefits of UKA; however, the optimal alignment of the tibial component is still debated. The purpose of this study was to evaluate the effects of tibial coronal and sagittal plane alignment in UKA on knee kinematics and cruciate ligament tension, using a musculoskeletal computer simulation.MethodsThe tibial component was first aligned perpendicular to the mechanical axis of the tibia, with a 7° posterior slope (basic model). Subsequently, coronal and sagittal plane alignments were changed in a simulation programme. Kinematics and cruciate ligament tensions were simulated during weight-bearing deep knee bend and gait motions. Translation was defined as the distance between the most medial and the most lateral femoral positions throughout the cycle.ResultsThe femur was positioned more medially relative to the tibia, with increasing varus alignment of the tibial component. Medial/lateral (ML) translation was smallest in the 2° varus model. A greater posterior slope posteriorized the medial condyle and increased anterior cruciate ligament (ACL) tension. ML translation was increased in the > 7° posterior slope model and the 0° model.ConclusionThe current study suggests that the preferred tibial component alignment is between neutral and 2° varus in the coronal plane, and between 3° and 7° posterior slope in the sagittal plane. Varus > 4° or valgus alignment and excessive posterior slope caused excessive ML translation, which could be related to feelings of instability and could potentially have negative effects on clinical outcomes and implant durability. Cite this article: K. Sekiguchi, S. Nakamura, S. Kuriyama, K. Nishitani, H. Ito, Y. Tanaka, M. Watanabe, S. Matsuda. Bone Joint Res 2019;8:126–135. DOI: 10.1302/2046-3758.83.BJR-2018-0208.R2.

Background Recurrent varus deformity and poor outcome sometimes occur following open-wedge high tibial osteotomy, but the mechanism remains unclear. The hypothesis of this study was that an excessively large medial proximal tibial angle with lateral joint surface inclination can worsen postoperative knee biomechanics. Methods A computer-simulated knee model was validated based on a volunteer knee. Osteotomy models with medial proximal tibial angles ranging from 90° to 97° in 1° increments were developed. Varus alignment correction of the distal femur was performed in each model to maintain identical coronal alignment passing through a point 62.5% lateral to the tibial plateau. The peak tibiofemoral contact forces and knee kinematics were compared in each model during walking and squatting. Findings All the osteotomy models demonstrated higher peak contact forces on the lateral tibiofemoral joints than on the medial tibiofemoral joints during walking. However, larger medial proximal tibial angles caused excessive increases in medial tibiofemoral contact forces, and the dominant tibiofemoral contact forces shifted to the medial side. Increased medial proximal tibial angles also caused progressive medial collateral ligament tension in knee flexion, but partial medial collateral ligament release effectively reduced medial tibiofemoral contact forces. Models with large medial proximal tibial angles showed nonphysiological roll-forward of the lateral femoral condyle during squatting and no screw-home movement around knee extension. Interpretation Excessively large medial proximal tibial angles following open-wedge high tibial osteotomy resulted in increased medial tibiofemoral contact forces and abnormal knee kinematics during knee flexion due to medial joint line elevation and ligament imbalance.

Backgrounds The correlation between in vivo knee kinematics and alignment has not been fully elucidated. Recently, similar or better clinical outcomes have been reported by restoration of mild varus alignment after total knee arthroplasty for preoperative varus knees. The aim of this study was to evaluate the effect of postoperative alignment on knee kinematics during a deep knee bend activity. Methods In vivo knee kinematics of 36 knees (25 patients) implanted with tri-condylar total knee arthroplasty were analyzed with a three dimensional model fitting approach using fluoroscopy. Under fluoroscopic surveillance, individual video frames were digitized at 30° increments from full extension to maximum flexion. Postoperative coronal and sagittal alignments were assessed using radiographs, and rotational alignment was assessed with computed tomography. Pearson correlation coefficients were calculated to determine the correlations between the alignment data and kinematic factors. Findings Correlation analysis showed that coronal alignment was significantly correlated with knee kinematics. The varus alignment of the limb and tibial component led to a greater axial rotation from full extension to maximum flexion and more rotated position in the mid to deep flexion range. Neither the rotational alignment of the femoral nor tibial components showed significant correlation with axial rotation from full extension to maximum flexion. Interpretation Varus alignment resulted in greater axial rotation, which could represent near-normal knee kinematics. The current study can be a kinematic rationale reporting similar or better clinical and functional outcomes for the total knee arthroplasty with residual varus alignment.

Increases in posterior tibial slope (PTS) with open-wedge high tibial osteotomy (OWHTO) are often related to two surgical errors: Symmetric opening of the osteotomy gap and a tendency to open the gap from the anteromedial direction. The study objective was to define trends in these two errors using computer simulation and clinical effects of their countermeasures. First, 60 knees with varus deformity were assessed with three-dimensional (3D) planning using computed tomography to allow for the mechanical axis to pass through a point at 62.5% of the width of the tibial plateau, defined as the weight-bearing line percentage (WBL%). Anterior and posterior widths of the opening gap to maintain PTS were measured. The effect on PTS when osteotomy gaps were opened from the anteromedial direction up to 30° was evaluated. Mean anterior width (y) was 6.6 mm (range, 2.2-10.9) and mean posterior width (x) was 9.1 mm (range, 3.9-15.7), which can be expressed as y = 0.75x - 0.24. Opening gaps from the anteromedial direction at 10°, 20°, and 30° led to a mean PTS increase of 1.9°, 3.9°, and 5.6°, respectively. In most cases, WBL% with anteromedial opening at 30° passed through a point at less than 60%. In 47 knees that underwent OWHTO using 3D planning, postoperative coronal and sagittal bone corrections were mostly accurate. However, postoperative WBL% was negatively correlated with correction angle because of difficulties in predicting medial joint tightness. Preoperative 3D planning for OWHTO can reduce surgical errors, but postoperative WBL% remains variable. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res.

The thickness and the grade of the articular cartilages of the knee of 34 patients who underwent total knee arthroplasty were evaluated by ultrasound (US) and by histology. The US grade correlated with the histological grade and the thickness of the articular cartilage measured by US. The thickness measured by US was significantly correlated with that measured by histology for the medial condyle. The US thickness was significantly less than the histological thickness for thicker articular cartilages. US grading and the thickness of the articular cartilages evaluated by US is sufficiently reliable to indicate their histological status.

Background In general, the flexion gap is larger than the extension gap with posterior cruciate ligament-sacrificing total knee arthroplasty. Several methods compensate for an excessive flexion gap, but their effects are unknown. The purpose of this study was to compare three methods to compensate for an increased flexion gap. Methods In this study, squatting in knees with excessive (4 mm) and moderate (2 mm) flexion gaps was simulated in a computer model. Differences in knee kinematics and kinetics with joint line elevation, setting the femoral component in flexion, and using a larger femoral component as compensatory methods were investigated. Findings The rotational kinematics during flexion with setting the femoral component in flexion were opposite to those in the other models. Using a larger femoral component resulted in the most physiological motion. The peak anterior translation was 10 mm in the joint line elevation model compared with approximately 6 mm in the other models. In the joint line elevation model, patellofemoral contact stress was excessively increased at 90° of knee flexion. In contrast, tibiofemoral contact stress was higher during knee extension with setting the femoral component in flexion due to anterior impingement. There were few differences in the effect of the three compensatory methods with a moderate flexion gap. Interpretation A larger femoral component should be used to compensate for an excessive flexion gap because it has less negative impact on posterior cruciate ligament-sacrificing total knee arthroplasty, whereas any compensation method might be acceptable for a moderate flexion gap.

Because immunity against Staphylococcus aureus has not been fully elucidated, there is no diagnostic test to gauge how robust a patient’s host response is likely to be. Therefore, we aimed to develop a test for specific antibodies in serum with diagnostic and prognostic potential. We describe the development and validation of a multiplex immunoassay for characterizing a patient’s immune response against 14 known S aureus antigens, which we then used to answer four questions: (1) Do certain antigens predominate in the immune response against S aureus? (2) Is there a predominant pattern of antigens recognized by patients and mice with infections? (3) Is the immunoglobulin G (IgG) response to any single antigen a useful predictor of ongoing S aureus infection? (4) Does measurement of the combined response against all 14 antigens provide a better predictor of ongoing infection? A case-control study was performed. Sera were collected from 35 consecutive patients with S aureus culture-confirmed (methicillin-sensitive S aureus or methicillin-resistant S aureus) musculoskeletal infections (deep implant-associated, osteomyelitis, and cases of established septic arthritis). Patients were excluded only if they did not give informed consent for participation. Twenty-four patients had implant infections after total joint replacements, five had fracture implant infections, four had native knee infections, and two had chronic osteomyelitis without an implant. Control patients were chosen from a group of healthy, medically optimized patients scheduled to undergo elective arthroplasty. Control patients were matched for age (± 3 years), BMI (± 3 kg/m2), and sex as closely as possible to patients with infections. Sera from patients with S aureus infections and murine S aureus tibial implant infections were used to evaluate a multiplex immunoassay for immunoglobulin titers against 14 recombinant S aureus antigens. All patients were treated with organism-targeted antibiotic therapy and appropriate, timely surgery. Treatment response was monitored with clinical examination, erythrocyte sedimentation rate, C-reactive protein, and resampling of the infection site for the pathogen as needed. Elevated inflammatory markers or persistent positive culture results were considered evidence of ongoing infection. Treatment provided was considered standard-of-care therapy in our medical center and all patients were treated jointly with a board-certified infectious disease specialist. Four antigens elicited more than 65% of the measurable IgG, the most dominant being against iron-regulated surface determinant protein B (IsdB). Patients with infections had different patterns of elevated IgG titers, so that no single titer was elevated in more than 50% of patients with infections (area under the curve [AUC] ≤ 0.80). Multivariate analysis of IgG titers yielded greater predictive power of S aureus infection (AUC = 0.896). Patients with infections who had high titers against IsdB (median of survivors, 7.28 [25%–75% range, 2.22–21.26] vs median of patients with infection-related death, 40.41 [25%–75% range, 23.57–51.37], difference of medians, 33.13; p = 0.043) and iron-regulated surface determinant protein A (IsdA) median of survivors, 2.21 [25%–75% range, 0.79–9.11] vs median of patients with infection-related death, 12.24 [25%–75% range, 8.85–15.95], difference of medians, 10.03; p = 0.043) were more likely to die from infections than those who did not have high titers of IsdB. Measurement of the host antibody response is a predictor of ongoing infection that may prove to have prognostic value. Future studies will seek to enlarge the patient population with infections to allow us to reduce the number of antigens required to achieve a stronger predictive power. Measurement of the immune response against S aureus with this diagnostic tool may help guide future studies on prophylaxis and therapy in an era of personalized medicine and pathogen-specific therapies.

While it is well known that Staphylococcus aureus establishes chronic implant-associated osteomyelitis by generating and persisting in biofilm, research to elucidate pathogen, and host specific factors controlling this process has been limited due to the absence of a quantitative in vivo model. To address this, we developed a murine tibia implant model with ex vivo region of interest (ROI) imaging analysis by scanning electron microscopy (SEM). Implants were coated with Staphylococcus aureus strains (SH1000, UAMS-1, USA300LAC) with distinct in vitro biofilm phenotypes, were used to infect C57BL/6 or Balb/c mice. In contrast to their in vitro biofilm phenotype, results from all bacteria strains in vivo were similar, and demonstrated that biofilm on the implant is established within the first day, followed by a robust proliferation phase peaking on Day 3 in Balb/c mice, and persisting until Day 7 in C57BL/6 mice, as detected by SEM and bioluminescent imaging. Biofilm formation peaked at Day 14, covering ∼40% of the ROI coincident with massive agr-dependent bacterial emigration, as evidenced by large numbers of empty lacunae with few residual bacteria, which were largely culture negative (80%) and PCR positive (87.5%), supporting the clinical relevance of this implant model. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 33:1311–1319, 2015.

Background: Plug protuberance occasionally occurs in osteochondral autologous transplantation (OAT). The incongruity of plugs results in poor clinical outcomes, especially in cases of protuberance. However, a surgical procedure to deal with this problem has not been reported. Purpose/Hypothesis: The purpose was to evaluate the efficacy and safety of cartilage resection of elevated plugs, with the hypothesis that patients whose elevated plugs were resected and leveled would achieve clinical outcomes equivalent to those of patients with flush plugs. Study Design: Cohort study; Level of evidence, 3. Methods: Cases (group P) included 22 patients who underwent OAT of the knee and whose plugs showed protuberance greater than 1 mm that was resected with a scalpel to obtain smooth congruity, while controls (group C) included 22 background-matched patients who did not require plug resection. The International Knee Documentation Committee (IKDC) subjective score, IKDC objective grade, and Japanese Orthopaedic Association score for knee osteoarthritis (JOA knee score) were used preoperatively and at the final follow-up (mean ± SD, 49.3 ± 18.1 months). International Cartilage Repair Society (ICRS) Cartilage Repair Assessment was used to evaluate lesion healing during the second-look arthroscopy. Results: IKDC subjective scores of group C (82.5 ± 11.8) and group P (82.1± 15.1) showed no difference at the final follow-up. On postoperative IKDC objective grading, 86% of group C and 82% of group P patients were graded as “nearly normal” or better ( P = .639). The mean JOA knee scores of group C (90.9 ± 8.9) and group P (90.1 ± 9.5) did not differ significantly ( P = .647). Nine second-look arthroscopies were performed in group C versus 8 in group P, and all patients had plugs that were graded as “nearly normal” or better by the ICRS Cartilage Repair Assessment. Larger plugs tended to be used in those patients who required resection. Conclusion: Resection of the elevated plug surface did not negatively affect patient outcomes in the midterm follow-up period.