Search

Interfacial layers in conjunction with suitable charge-transport layers can significantly improve the performance of optoelectronic devices by facilitating efficient charge carrier injection and extraction. This work uses a neat C60 interlayer on the anode to experimentally reveal that surface recombination is a significant contributor to nonradiative recombination losses in organic solar cells. These losses are shown to proportionally increase with the extent of contact between donor molecules in the photoactive layer and a molybdenum oxide (MoO3) hole extraction layer, proven by calculating voltage losses in low- and high-donor-content bulk heterojunction device architectures. Using a novel in-device determination of the built-in voltage, the suppression of surface recombination, due to the insertion of a thin anodic-C60 interlayer on MoO3, is attributed to an enhanced built-in potential. The increased built-in voltage reduces the presence of minority charge carriers at the electrodes-a new perspective on the principle of selective charge extraction layers. The benefit to device efficiency is limited by a critical interlayer thickness, which depends on the donor material in bilayer devices. Given the high popularity of MoO3 as an efficient hole extraction and injection layer and the increasingly popular discussion on interfacial phenomena in organic optoelectronic devices, these findings are relevant to and address different branches of organic electronics, providing insights for future device design.

Efficient exciton dissociation and subsequent generation of free charge carriers at the organic donor-acceptor interface requires a number of electron-transfer processes. It is a common view that these steps result in an unavoidable energy loss in organic photovoltaic devices that is not present in other types of solar cells. The currently best performing organic solar cells with power conversion efficiencies over 16% challenge this view, and no interfacial charge-transfer states with energy significantly lower than the strongly absorbing singlet states are detected within the gap of the used donor and acceptor materials. This Perspective will discuss implications, the remaining sources of energy loss, and open questions to be solved to achieve power conversion efficiencies over 20%.

A significant number of organic electronic devices rely on blends of electron-donating and electron-accepting molecules. In bulk heterojunction organic photovoltaics, the nanoscopic phase behavior of the two individual components within the photoactive layer has a major impact on the charge separation and charge transport properties. For polymer:fullerene solar cells, it has been hypothesized that an increased accessibility of the electron-deficient monomer unit in push-pull type low bandgap polymers allows for fullerene ‘docking’. The close proximity of electron donor and acceptor molecules enables more efficient charge transfer, which is beneficial for the device efficiency. With this in mind, we synthesized a series of PBDTTPD [poly(benzodithiophene-thienopyrroledione)] low bandgap copolymers with varying side chains. Solar cells were fabricated for all polymers and the device characteristics were compared. The combination of proton wideline solid-state NMR (ssNMR) relaxometry and sensitive external quantum efficiency (sEQE) measurements was shown to provide essential information on donor-acceptor interactions and phase separation in bulk heterojunction organic photovoltaics. The reduced charge transfer state absorption and the observed phase separation of crystalline PC71BM domains for the polymers containing the most accessible methyl-TPD unit indicate a diminished contact between donor and acceptor, leading to a loss in performance.

An understanding of the factors limiting the open-circuit voltage (V-oc) and related photon energy loss mechanisms is critical to increase the power conversion efficiency (PCE) of small-molecule organic solar cells (OSCs), especially those with near-infrared (NIR) absorbers. In this work, two NIR boron dipyrromethene (BODIPY) molecules are characterized for application in planar (PHJ) and bulk (BHJ) heterojunction OSCs. When two H atoms are substituted by F atoms on the peripheral phenyl rings of the molecules, the molecular aggregation type in the thin film changes from the H-type to J-type. For PHJ devices, the nonradiative voltage loss of 0.35 V in the J-aggregated BODIPY is lower than that of 0.49 V in the H-aggregated device. In BHJ devices with a nonradiative voltage loss of 0.35 V, a PCE of 5.5% is achieved with an external quantum efficiency (EQE) maximum of 68% at 700 nm.

The involvement of charge-transfer (CT) states in the photogeneration and recombination of charge carriers has been an important focus of study within the organic photovoltaic community. In this work, we investigate the molecular factors determining the mechanism of photocurrent generation in low-donor-content organic solar cells, where the active layer is composed of vacuum-deposited C

The energetic landscape of charge transfer (CT) states at the interface of electron donating and electron accepting domains in organic optoelectronic devices is crucial for their performance. Central questions -- such as the role of static energetic disorder and vibrational effects -- are under ongoing dispute. This study provides an in-depth analysis of temperature dependent broadening of the spectroscopic absorption and emission features of CT states in devices with small molecule-fullerene blends. We confirm the validity of the electro-optical reciprocity relation between the photovoltaic external quantum efficiency ($\mathrm{EQE_{PV}}$) and electroluminescence ($\mathrm{EQE_{EL}}$), enabling us to validate the device temperature during the experiment. The validated temperature allows us to fit our experimental data with several models, and compare extracted CT state energies with the corresponding open circuit voltage limit at $0\mathrm{\,K}$. Our findings unveil that the absorption and emission characteristics are usually not symmetric, and dominated by temperature-activated broadening (vibrational) effects instead of static disorder., 11 pages, 5 figures submitted to: Physical Review Applied

Organic solar cells are approaching power conversion efficiencies of other thin‐film technologies. However, in order to become truly market competitive, the still substantial voltage losses need to be reduced. Here, the synthesis and characterization of four novel arylamine‐based push‐pull molecular donors was described, two of them exhibiting a methyl group at the para‐position of the external phenyl ring of the arylamine block. Assessing the charge‐transfer state properties and the effects of methylation on the open‐circuit voltage of the device showed that devices based on methylated versions of the molecular donors exhibited reduced voltage losses due to decreased non‐radiative recombination. Modelling suggested that methylation resulted in a tighter interaction between donor and acceptor molecules, turning into a larger oscillator strength to the charge‐transfer states, thereby ensuing reduced non‐radiative decay rates., Structural tuning improves efficiency: Modification of the molecular structure of organic molecules allows to influence the performance of organic photovoltaic devices. Addition of a methyl group in the para‐position of the external phenyl ring leads to increase in open‐circuit voltage. Quantum‐chemical calculations attribute this effect to the increase of the oscillator strength of the electronic transition between the donor and acceptor.

Organic solar cells usually utilise a heterojunction between electron-donating (D) and electron-accepting (A) materials to split excitons into charges. However, the use of D-A blends intrinsically limits the photovoltage and introduces morphological instability. Here, we demonstrate that polycrystalline films of chemically identical molecules offer a promising alternative and show that photoexcitation of α-sexithiophene (α-6T) films results in efficient charge generation. This leads to α-6T based homojunction organic solar cells with an external quantum efficiency reaching up to 44% and an open-circuit voltage of 1.61 V. Morphological, photoemission, and modelling studies show that boundaries between α-6T crystalline domains with different orientations generate an electrostatic landscape with an interfacial energy offset of 0.4 eV, which promotes the formation of hybridised exciton/charge-transfer states at the interface, dissociating efficiently into free charges. Our findings open new avenues for organic solar cell design where material energetics are tuned through molecular electrostatic engineering and mesoscale structural control., Though single-material organic solar cells are attractive for next-generation photovoltaic technologies, designing new materials with ideal properties remains a challenge. Here, the authors report the use of orientation-dependent molecular electrostatics to realise efficient homojunction devices.

Interfaces between organic electron-donating (D) and electron-accepting (A) materials can show efficient free charge carrier generation upon illumination, enabling organic photovoltaic devices and photodetectors with photon to electron conversion yields approaching 100%. Recently, organic light-emitting diodes (OLEDs) based on charge transfer (CT) (or exciplex) emission occurring at such D-A interfaces have been shown to exhibit high electroluminescence external quantum yields (EQEEL). However, no organic D-A combination with both a high EQEEL, as well as a high free carrier generation yield has been discovered so far. Such a system would result in significantly higher operating voltages in organic solar cells, reduced dark current in organic photodetectors, and reduced driving voltages for OLEDs.

The low-energy edge of optical absorption spectra is critical for the performance of solar cells, but is not well understood in the case of organic solar cells (OSCs). We study the microscopic origin of exciton bands in molecular blends and investigate their role in OSCs. We simulate the temperature dependence of the excitonic density of states and low-energy absorption features, including low-frequency molecular vibrations and multi-exciton hybridisation. For model donor-acceptor blends featuring charge-transfer excitons, our simulations agree very well with temperature-dependent experimental absorption spectra. We unveil that the quantum effect of zero-point vibrations, mediated by electron-phonon interaction, causes a substantial exciton bandwidth and reduces the open-circuit voltage, which is predicted from electronic and vibronic molecular parameters. This effect is surprisingly strong at room temperature and can substantially limit the OSC's efficiency. Strategies to reduce these vibration-induced voltage losses are discussed for a larger set of systems and different heterojunction geometries.

The origin of energetic disorder in organic semiconductors and its impact on opto-electronic properties remains a topic of intense controversy. Particularly the disorder at electron donor-acceptor interfaces for organic photovoltaics is pivotal to understand as it is expected to affect photo-carrier generation, recombination and consequently device efficiency parameters. In this work we evaluate the temperature dependence of the line-shape of the photoluminescence (PL) and electroluminescence (EL) spectra of small molecule:fullerene blend devices, with the ambition to disentangle dynamic and static disorder contributions. The EL emission spectra are dominated by charge-transfer (CT) state emission and are confirmed to be of Gaussian character and almost completely voltage independent. More importantly, a strong line-width narrowing is persistently observed upon cooling, down to a certain material specific low temperature, below which the line-width remains constant. It is consequently clear that the main portion of the line-width measured at operating conditions of room temperature or higher, is originating from thermally activated, or dynamic, disorder. The observed temperature dependence of the high-energy emission tail can be fully described by taking into account high and low frequency molecular vibrational modes, without having to rely on static disorder. The presence of low frequency molecular modes with large Huang-Rhys factors results in a Gaussian line-shape, which is additionally broadened at high temperature by thermal population of high frequency intra-molecular modes. We therefore cast strong doubts regarding the commonly used assumption that single temperature optical measurements of absorption or emission tails are able to provide meaningful information regarding the shape of a static density of states tail. K. T. acknowledges the German Research Foundation (DFG) through project 382633022 (RECOLPER) and the Experimental Physics VI chair of Prof. Vladimir Dyakonov at Wurzburg University. J. B. acknowledges the DFG project VA 1035/5-1 (Photogen) and the Sachsische Aufbaubank through project no. 100325708 (Infrakart). The authors also acknowledge discussion on the topic with Robert Street, Thomas Kirchartz, Frank Ortmann and Carsten Deibel. Tvingstedt, K (corresponding author), Julius Maximilian Univ Wurzburg, Expt Phys 6, D-97074 Wurzburg, Germany. ktvingstedt@physik.uni-wuerzburg.de

The best performing organic solar cells (OSC) efficiently absorb photons and convert them to free charge carriers, which are subsequently collected at the electrodes. However, the energy lost in this process is much larger than for inorganic and perovskite solar cells, currently limiting the power conversion efficiency of OSCs to values slightly below 14%. To quantify energy losses, the open-circuit voltage of the solar cell is often compared to its optical gap. The latter is, however, not obvious to determine for organic materials which have broad absorption and emission bands, and is often done erroneously. Nevertheless, a deeper understanding of the energy loss mechanisms depends crucially on an accurate determination of the energies of the excited states involved in the photo-conversion process. This perspective therefore aims to summarize how the optical gap can be precisely determined, and how it relates to energy losses in organic photovoltaic materials. This work received funding from the German Federal Ministry for Education and Research (BMBF) through the InnoProle Projekt “Organische p–i–n Bauelemente 2.2” (03IPT602X).

We have designed a small molecule based on benzothiadiazole-triphenylamine moieties (BTD-TPA(2)), composed of an electron-poor benzothiadiazole core with two electron-rich triphenylamine arms. BTD-TPA(2) was synthesized in a facile manner using a Suzuki cross-coupling reaction. The molecule was rationally designed to take advantage of the synergistic effect of BTD, which allows the formation of a favorable band gap material, and triphenylamine (TPA) moieties, which favour efficient hole extraction and transport properties. A thin layer of BTD-TPA(2) was placed between the photo-active DBP/C-70 layer stack and the MoOx electrical contact. With an optimized interlayer thickness of 35 nm, the attained photovoltaic properties were substantially superior to those of the reference devices. This has its origin in the dual functionality of BTD-TPA(2), i.e., efficient exciton blocking and improved hole extraction at the anode contact. The obtained results led to an improved power conversion efficiency of 5.66% for a vacuum deposited bilayer DBP/C-70 solar cell, which will be the new state of the art for bilayer DBP based solar cells. This project has received funding from the European Union Seventh Framework Programme under grant agreement no. 607232 [THINFACE] and is partially supported by a European Research Council grant [MOLEMAT, 72630], as well as by the German Federal Ministry for Education and Research (BMBF) through the InnoProfille project "Organische p-i-n Bauelemente 2.2' (803IPT602X).

Three furan-fused BODIPYs were synthesized with perfluorinated methyl, ethyl and n-propyl groups on the meso-carbon. They were obtained with high yields by reacting the furan-fused 2-carboxylpyrrole in corresponding perfluorinated acid and anhydride. With the increase in perfluorinated alkyl chain length, the molecular packing in the single crystal is influenced, showing increasing stacking distance and decreasing slope angle. All the BODIPYs were characterized as intense absorbers in near infrared region in solid state, peaking at similar to 800 nm with absorption coefficient of over 280 000 cm(-1). Facilitated by high thermal stability, the furan-fused BODIPYs were employed in vacuum-deposited organic solar cells as electron donors. All devices exhibit PCE over 6.0% with the EQE maximum reaching 70% at similar to 790 nm. The chemical modification of the BODIPY donors have certain influence on the active layer morphology, and the highest PCE of 6.4% was obtained with a notably high jsc of 13.6 mA cm(-2). Sensitive EQE and electroluminance studies indicated that the energy losses generated by the formation of a charge transfer state and the radiative recombination at the donor-acceptor interface were comparable in the range of 0.14-0.19 V, while non-radiative recombination energy loss of 0.38 V was the main energy loss route resulting in the moderate V-oc of 0.76 V.

Strong light-matter coupling can re-arrange the exciton energies in organic semiconductors. Here, we exploit strong coupling by embedding a fullerene-free organic solar cell (OSC) photo-active layer into an optical microcavity, leading to the formation of polariton peaks and a red-shift of the optical gap. At the same time, the open-circuit voltage of the device remains unaffected. This leads to reduced photon energy losses for the low-energy polaritons and a steepening of the absorption edge. While strong coupling reduces the optical gap, the energy of the charge-transfer state is not affected for large driving force donor-acceptor systems. Interestingly, this implies that strong coupling can be exploited in OSCs to reduce the driving force for electron transfer, without chemical or microstructural modifications of the photo-active layer. Our work demonstrates that the processes determining voltage losses in OSCs can now be tuned, and reduced to unprecedented values, simply by manipulating the device architecture., Strong light-matter coupling can tune exciton properties but its effect in photovoltaics remains unexplored. Here Nikolis et al. show that the photon energy loss from optical gap to open-circuit voltage can be reduced to unprecedented values by embedding organic solar cells in optical microcavities.

Organic solar cells are thought to suffer from poor thermal stability of the active layer nanostructure, a common belief that is based on the extensive work that has been carried out on fullerene-based systems. We show that a widely studied non-fullerene acceptor, the indacenodithienothiophene-based acceptor ITIC, crystallizes in a profoundly different way as compared to fullerenes. Although fullerenes are frozen below the glass-transition temperature T-g of the photovoltaic blend, ITIC can undergo a glass-crystal transition considerably below its high T-g of similar to 180 degrees C. Nanoscopic crystallites of a low-temperature polymorph are able to form through a diffusion-limited crystallization process. The resulting fine-grained nanostructure does not evolve further with time and hence is characterized by a high degree of thermal stability. Instead, above T-g, the low temperature polymorph melts, and micrometer-sized crystals of a high-temperature polymorph develop, enabled by more rapid diffusion and hence long-range mass transport. This leads to the same detrimental decrease in photovoltaic performance that is known to occur also in the case of fullerene-based blends. Besides explaining the superior thermal stability of non-fullerene blends at relatively high temperatures, our work introduces a new rationale for the design of bulk heterojunctions that is not based on the selection of high-T-g materials per se but diffusion-limited crystallization. The planar structure of ITIC and potentially other non-fullerene acceptors readily facilitates the desired glass-crystal transition, which constitutes a significant advantage over fullerenes, and may pave the way for truly stable organic solar cells. We acknowledge financial support from the Knut and Alice Wallenberg Foundation through the project "Mastering Morphology for Solution-borne Electronics", the Swedish Research Council (grant agreement no. 2016-06146), and the Swedish Foundation for Strategic Research (grant agreement no. RMA15-0052). We thank the Cornell High Energy Synchrotron Source (CHESS), supported by the NSF under award DMR-1332208, for providing time for GIWAXS measurements. J.B. and K.V. acknowledge funding from the German Federal Ministry for Education and Research (BMBF) through the InnoProfile project "Organische p-i-n Bauelemente 2.2" (03IPT602X).

Achieving long-term stability in organic solar cells is a remaining bottleneck for the commercialization of this otherwise highly appealing technology. In this work, we study the performance and stability differences in standard and inverted DBP/C-70 based organic solar cells. Differences in the charge-transfer state properties of inverted and standard configuration DBP/C-70 solar cells are revealed by sensitive external quantum efficiency measurements, leading to differences in the open-circuit voltages of the devices. The degradation of standard and inverted solar cell configurations at ISOS aging test conditions (ISOS-D-3 and ISOS-T-3) was investigated and compared. The results indicate that the performance drop in the small molecule bilayer solar cells is less related to changes at the D-A interface, suggesting also a pronounced morphological stability, and instead, in the case of inverted cells, dominated by degradation at the electron transport layer (ETL) bathocuproine (BCP). Photoluminescence measurements, electron-only-device characteristics, and stability measurements show improved exciton blocking, electron transport properties and a higher stability for BCP/Ag ETL stacks, giving rise to inverted devices with enhanced performance and device stability. The research leading to these results has received funding from the People Programme (Marie Curie Actions) of the European Union's Seventh Framework Programme FP7/2007-2013/under REA Grant Agreement No. 607232, THINFACE. J.B., D.S. and K.V. acknowledge the German Federal Ministry for Education and Research (BMBF) for funding the project through the InnoProfile project "Organische p-i-n Bauelemente 2.2".

Intermolecular charge-transfer states at the interface between electron donating (D) and accepting (A) materials are crucial for the operation of organic solar cells but can also be exploited for organic light-emitting diodes(1,2). Non-radiative charge-transfer state decay is dominant in state-of-the-art D-A-based organic solar cells and is responsible for large voltage losses and relatively low power-conversion efficiencies as well as electroluminescence external quantum yields in the 0.01-0.0001% range(3,4). In contrast, the electroluminescence external quantum yield reaches up to 16% in D-A-based organic light-emitting diodes(5-7). Here, we show that proper control of charge-transfer state properties allows simultaneous occurrence of a high photovoltaic and emission quantum yield within a single, visible-light-emitting D-A system. This leads to ultralow-emission turn-on voltages as well as significantly reduced voltage losses upon solar illumination. These results unify the description of the electro-optical properties of charge-transfer states in organic optoelectronic devices and foster the use of organic D-A blends in energy conversion applications involving visible and ultraviolet photons(8-11). This work was supported by the German Federal Ministry for Education and Research (BMBF) through the InnoProfile project 'Organische p-i-n Bauelemente 2.2' (03IPT602X) and by the German Research Foundation (DFG) project Photogen (VA 1035/5-1). X.J. and Y.L. acknowledge support from the China Scholarship Council (nos. 201706140127 and 201506920047, respectively). The authors also acknowledge the DFG for supporting K.T. (project 382633022 'RECOLPER'), F.P., S.Ro. and D.N. (SFB 951 'HIOS') and A.F. (RE 3198/6-1 'EFOD').

Fluorine-containing donor molecules TFTF, CNTF and PRTF are designed and isomer selectively synthesized for application in vacuum-deposited organic solar cells. These molecules comprise a donor acceptor molecular architecture incorporating thiophene and benzothiadiazole derivatives as the electron-donating and electron-withdrawing moieties, respectively. As opposed to previously reported materials from this class, PRTF can be purified by vacuum sublimation at moderate to high yields because of its higher volatility and better stabilization due to a stronger intramolecular hydrogen bond, as compared to TFTF and CNTF. The UV-vis absorption spectra of the three donors show an intense broadband absorption between 500 nm and 800 nm with, similar positions of their frontier energy levels. The photophysical properties of the three donor molecules are thoroughly tested and optimized in bulk heterojunction solar cells with C-60 as acceptor. PRTF shows the best performance, yielding power conversion efficiencies of up to 3.8%. Moreover, the voltage loss for the PRTF device due to the non radiative recombination of free charge carriers is exceptionally low (0.26 V) as compared to typical values for organic solar cells (>0.34V). (C) 2016 Published by Elsevier B.V.

Efficient charge generation in organic semiconductors usually requires an interface with an energetic gradient between an electron donor and an electron acceptor in order to dissociate the photogenerated excitons. However, single-component organic solar cells based on chloroboron subnaphthalocyanine (SubNc) have been reported to provide considerable photocurrents despite the absence of an energy gradient at the interface with an acceptor. In this work, it is shown that this is not due to direct free carrier generation upon illumination of SubNc, but due to a field-assisted exciton dissociation mechanism specific to the device configuration. Subsequently, the implications of this effect in bilayer organic solar cells with SubNc as the donor are demonstrated, showing that the external and internal quantum efficiencies in such cells are independent of the donor-acceptor interface energetics. This previously unexplored mechanism results in efficient photocurrent generation even though the driving force is minimized and the open-circuit voltage is maximized. V.C.N. and Y.D. contributed equally to this work. The authors would like to thank Prof. Dr. Dieter Neher for providing measurement time on the electroluminescence setup of his lab at University of Potsdam. They would also like to acknowledge the Optoelectronics group in the University of Cambridge for sharing the global analysis codes. This work was supported by the German Federal Ministry of Education and Research (BMBF) through the InnoProfile project "Organische p-i-n Bauelemente2.2" (FKZ 03IPT602X). A.A.B. is a Royal Society university research fellow. Open access funding enabled and organized by Projekt DEAL. Nikolis, VC (corresponding author), Tech Univ Dresden, Dresden Integrated Ctr Appl Phys & Photon Mat IAP, Nothnitzer Str 61, D-01187 Dresden, Germany ; Tech Univ Dresden, Inst Appl Phys, Nothnitzer Str 61, D-01187 Dresden, Germany. Bakulin, AA (corresponding author), Imperial Coll London, Mol Sci Res Hub, London W12 0BE, England. Vandewal, K (corresponding author), Hasselt Univ, Inst Mat Res IMO IMOMEC, Wetenschapspk 1, B-3590 Diepenbeek, Belgium. vasileios_christos.nikolis1@tu-dresden.de; a.bakulin@imperial.ac.uk; koen.vandewal@uhasselt.be

Organic solar cells with an electron donor diluted in a fullerene matrix have a reduced density of donor-fullerene contacts, resulting in decreased free-carrier recombination and increased open-circuit voltages. However, the low donor concentration prevents the formation of percolation pathways for holes. Notwithstanding, high (>75%) external quantum efficiencies can be reached, suggesting an effective hole-transport mechanism. Here, we perform a systematic study of the hole mobilities of 18 donors, diluted at similar to 6 mol % in C-60, with varying frontier energy level offsets and relaxation energies. We find that hole transport between isolated donor molecules occurs by long-range tunneling through several fullerene molecules, with the hole mobilities being correlated to the relaxation energy of the donor. The transport mechanism presented in this study is of general relevance to bulk heterojunction organic solar cells where mixed phases of fullerene containing a small fraction of a donor material or vice versa are present as well. The work was funded by the German Federal Ministry for Education and Research (BMBF) through the InnoProfile Projekt "Organische p-i-n Bauelemente 2.2" (03IPT602X). This work was supported by the Deutsche Forschungsgemeinschaft (project OR 349/1-1), by the Department of the Navy, Office of Naval Research Award No. N00014-14-1-0580 (CAOP MUM), by the German Ministry of Science and Education (BMBF), project UNVEiL, and through a state sponsored scholarship for graduate students to Y.F. from the China Scholarship Council. M.N. acknowledges funding from "Svenska Tekniska Vetenskapsakademien i Finland". Grants for computing time from the Center for Information Services and High Performance Computing (ZIH) are gratefully acknowledged.

Organic solar cells are a promising technology for a large area conversion of sunlight into electricity. In particular for solar cells based on oligomers (small molecules), efficient donor materials absorbing wavelengths larger than 780 nm are still rare. Here, we investigate three aza-BODIPY dyes absorbing in the infrared. The addition of side groups leads to a red shift of the optical gap from 802 to 818 nm. In optimized devices using these donors in a bulk heterojunction with C-60, we observe a higher charge carrier mobility and a higher power conversion efficiency for the molecules without a methyl or methoxy side group lowering the molecular reorganization energy. Surprisingly, the donor-acceptor blend with the lowest energy loss during the electron transfer to the C-60 yields the highest short circuit current. With increasing size of the attached side chain, the devices exhibit a larger trap density, measured by impedance spectroscopy. Based on the investigation of different blend ratios, we conclude that these traps are mainly present in the donor phase. (C) 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Organic solar cells demonstrate external quantum efficiencies and fill factors approaching those of conventional photovoltaic technologies. However, as compared with the optical gap of the absorber materials, their open-circuit voltage is much lower, largely due to the presence of significant non-radiative recombination. Here, we study a large data set of published and new material combinations and find that non-radiative voltage losses decrease with increasing charge-transfer-state energies. This observation is explained by considering non-radiative charge-transfer-state decay as electron transfer in the Marcus inverted regime, being facilitated by a common skeletal molecular vibrational mode. Our results suggest an intrinsic link between non-radiative voltage losses and electron-vibration coupling, indicating that these losses are unavoidable. Accordingly, the theoretical upper limit for the power conversion efficiency of single-junction organic solar cells would be reduced to about 25.5% and the optimal optical gap increases to (1.45-1.65) eV, that is, (0.2-0.3) eV higher than for technologies with minimized non-radiative voltage losses.

High photon energy losses limit the open-circuit voltage (V-OC) and power conversion efficiency of organic solar cells (OSCs). In this work, an optimization route is presented which increases the V-OC by reducing the interfacial area between donor (D) and acceptor (A). This optimization route concerns a cascade device architecture in which the introduction of discontinuous interlayers between alpha-sexithiophene (alpha-6T) (D) and chloroboron subnaphthalocyanine (SubNc) (A) increases the V-OC of an alpha-6T/SubNc/SubPc fullerene-free cascade OSC from 0.98 V to 1.16 V. This increase of 0.18 V is attributed solely to the suppression of nonradiative recombination at the D-A interface. By accurately measuring the optical gap (E-opt) and the energy of the charge-transfer state (E-CT) of the studied OSC, a detailed analysis of the overall voltage losses is performed. E-opt - qV(OC) losses of 0.58 eV, which are among the lowest observed for OSCs, are obtained. Most importantly, for the V-OC-optimized devices, the low-energy (700 nm) external quantum efficiency (EQE) peak remains high at 79%, despite a minimal driving force for charge separation of less than 10 meV. This work shows that low-voltage losses can be combined with a high EQE in organic photovoltaic devices.

In organic solar cells continuous donor and acceptor networks are considered necessary for charge extraction, whereas discontinuous neat phases and molecularly mixed donor–acceptor phases are generally regarded as detrimental. However, the impact of different levels of domain continuity, purity, and donor–acceptor mixing on charge transport remains only semiquantitatively described. Here, cosublimed donor–acceptor mixtures, where the distance between the donor sites is varied in a controlled manner from homogeneously diluted donor sites to a continuous donor network are studied. Using transient measurements, spanning from sub-picoseconds to microseconds photogenerated charge motion is measured in complete photovoltaic devices, to show that even highly diluted donor sites (5.7%–10% molar) in a buckminsterfullerene matrix enable hole transport. Hopping between isolated donor sites can occur by long-range hole tunneling through several buckminsterfullerene molecules, over distances of up to ≈4 nm. Hence, these results question the relevance of “pristine” phases and whether a continuous interpenetrating donor–acceptor network is the ideal morphology for charge transport. Funding agencies: German Federal Ministry for Education and Research (BMBF) through the InnoProfille project "Organische p-i-n Bauelemente 2.2"; Research Council of Lithuania [MIP-85/2015]; Science Council of Sweden; Knut and Alice Wallenberg foundation; Wallenberg Scholar

In this review, we summarize design principles of organic solar cells with plasmonic nanostructures. A process for scalable vacuum processing of silver nanoparticles is presented. Approximations for losses inside plasmonic structures are derived with respect to particle size and absorber material. We evaluate the characteristic length scales of plasmonic near-field enhancement and backscattering. The thickness of the absorber layers can be significantly reduced in plasmonic devices showing increased power conversion efficiency. The strongest plasmonic effects are observed in coupling particle structures.

The nanoscale morphology of the bulk heterojunction absorber layer in an organic solar cell (OSC) is of key importance for its efficiency. The morphology of high performance vacuum-processed, small molecule OSCs based on oligothiophene derivatives (DCV5T-Me) blended with C60 on various length scales is studied. The analytical electron microscopic techniques such as scanning transmission electron microscopy, energy dispersive X-ray spectroscopy, highly sensitive external quantum efficiency measurements, and meso and nanoscale simulations are employed. Unique insights into the relation between processing, morphology, and efficiency of the final devices are obtained. It is shown that the connectivity of the oligothiophene-C60 network is independent of the material domain size. The decisive quantity controlling the internal quantum efficiency is the energetic disorder induced by material mixing, strongly limiting charge and exciton transport in the OSCs.

Conjugated polymers and small molecules based on alternating electron-donating (D) and electronaccepting (A) building blocks have led to state-of-the-art organic solar cell materials governing efficiencies beyond 10%. Unfortunately, the connection of D and A building blocks via cross-coupling reactions does not always proceed as planned, which can result in the generation of side products containing D-D or A-A homocoupling motifs. Previous studies have reported a reduced performance in polymer and small molecule solar cells when such defect structures are present. A general consensus on the impact of homocouplings on device performance is, however, still lacking as is a profound understanding of the underlying causes of the device deterioration. For differentiating the combined effect of molecular weight and homocouplings in polymer solar cells, a systematic study on a small molecule system (DTS(FBBTh2)2) is presented. The impact of homocouplings on nanomorphology, thermal, and electro-optical properties is investigated. It is demonstrated that small quantities of homocouplings (

Stability is now a critical factor in the commercialization of organic photovoltaic (OPV) devices. Both extrinsic stability to oxygen and water and intrinsic stability to light and heat in inert conditions must be achieved. Triplet states are known to be problematic in both cases, leading to singlet oxygen production or fullerene dimerization. The latter is thought to proceed from unquenched singlet excitons that have undergone intersystem crossing (ISC). Instead, we show that in bulk heterojunction (BHJ) solar cells the photo-degradation of C60 via photo-oligomerization occurs primarily via back-hole transfer (BHT) from a charge-transfer state to a C60 excited triplet state. We demonstrate this to be the principal pathway from a combination of steady-state optoelectronic measurements, time-resolved electron paramagnetic resonance, and temperature-dependent transient absorption spectroscopy on model systems. BHT is a much more serious concern than ISC because it cannot be mitigated by improved exciton quenching, obtained for example by a finer BHJ morphology. As BHT is not specific to fullerenes, our results suggest that the role of electron and hole back transfer in the degradation of BHJs should also be carefully considered when designing stable OPV devices., The commercialisation of organic photovoltaic technology calls for research on material degradation mechanisms. Ramirez et al. show that triplet excitons produced by back charge transfer can significantly impact the photo-stability of fullerene-based devices even in the absence of water and oxygen.

The best organic solar cells (OSCs) achieve comparable peak external quantum efficiencies and fill factors as conventional photovoltaic devices. However, their voltage losses are much higher, in particular those due to nonradiative recombination. To investigate the possible role of triplet states on the donor or acceptor materials in this process, model systems comprising Zn- and Cu-phthalocyanine (Pc), as well as fluorinated versions of these donors, combined with C-60 as acceptor are studied. Fluorination allows tuning the energy level alignment between the lowest energy triplet state (T-1) and the charge-transfer (CT) state, while the replacement of Zn by Cu as the central metal in the Pcs leads to a largely enhanced spin-orbit coupling. Only in the latter case, a substantial influence of the triplet state on the nonradiative voltage losses is observed. In contrast, it is found that for a large series of typical OSC materials, the relative energy level alignment between T-1 and the CT state does not substantially affect nonradiative voltage losses. This work was supported by the German Federal Ministry for Education and Research (BMBF) through the InnoProfile project "Organische p-i-n Bauelemente 2.2" and the European Union's Horizon 2020 research and innovation programme under Marie Sklodowska Curie Grant agreement No. 722651 (SEPOMO). F.P. and D.N. acknowledge funding by the German Research Foundation (DFG) via the SFB 951 "HIOS". The authors acknowledge Prof. K. Leo and V. C. Nikolis for fruitful discussions. The authors thank Dr. B. Beyer for supplying ZnF4Pc and CuF4Pc as well as Dr. M. Lau for the synthesis of F4CuPc. Additionally, the authors thank Prof. Bauerle from University of Ulm for the supply of DH4T, DH6T, and several DCV2-nT-R. Furthermore, the authors acknowledge Dr. F. Holzmueller, M. Saalfrank, and Dr. R. Meerheim for providing OSC devices for this study. Computational resources were provided by the Consortium des Equipements de Calcul Intensif (CECI), funded by the Fonds de la Recherche Scientifiques de Belgique (F.R.S.-FNRS) under Grant No. 2.5020.11, as well as the Tier-1 supercomputer of the Federation Wallonie-Bruxelles, infrastructure funded by the Walloon Region under Grant Agreement No. 1117545. D.B. is a FNRS Research Director.