Search

This study discusses weathering-induced oxidation of polystyrene with and without different concentrations of the antioxidant Irgafos using Laser-induced Breakdown Spectroscopy (LIBS). By examining the spectral feature of oxidation and due to laser ablation, a systematical analysis of the oxygen content on the sample’s surface and its penetration depth could be conducted. The results show that LIBS can be used as a fast technique for the quantification of weathering-induced oxidation.

Composites based on fully bio-based epoxy-amine resins reinforced with recycled carbon fibers were obtained and compared to petro- and partially bio-based benchmark materials. Rheology measurements...

In transport sectors such as aviation, automotive and railway, materials combining a high lightweight potential with high flame retardant properties are in demand. Polymeric foams are suitable materials as they are lightweight, but often have high flammability. This study focuses on the influence of different flame retardants on the burning behavior of Novolac based epoxy foams using Isophorone Diamine carbamate (B-IPDA) as dual functional curing and blowing agent. The flame retardant properties and possible modifications of these foams are systematically investigated. Multiple flame retardants, representing different flame retardant mechanisms, are used and the effects on the burning behavior as well as mechanical and thermal properties are evaluated. Ammonium polyphosphate (APP), used with a filler degree of 20 wt.% or higher, functions as the best performing flame retardant in this study.

Polylactide (PLA) is one of the most important bioplastics worldwide and thus represents a good potential substitute for bead foams made of the fossil-based Polystyrene (PS). However, foaming of PLA comes with a few challenges. One disadvantage of commercially available PLA is its low melt strength and elongation properties, which play an important role in foaming. As a polyester, PLA is also very sensitive to thermal and hydrolytic degradation. Possibilities to overcome these disadvantages can be found in literature, but improving the properties for foaming of PLA as well as the degradation behavior during foaming have not been investigated yet. In this study, reactive extrusion on a twin-screw extruder is used to modify PLA in order to increase the melt strength and to protect it against thermal degradation and hydrolysis. PLA foams are produced in an already known process from the literature and the influence of the modifiers on the properties is estimated. The results show that it is possible to enhance the foaming properties of PLA and to protect it against hydrolysis at the same time., Deutsche Forschungsgemeinschaft

Increasing requirements are leading to new developments in bead foam materials. Engineering thermoplastics such as polybutylene terephthalate (PBT) outperform standard bead foams in thermal stability. In order to obtain molded parts, beads are fused together using steam chest molding. Classical theories for the fusion mechanism, explaining the molding of amorphous EPS (expandable polystyrene) or semi-crystalline EPP (expanded polypropylene), cannot be applied to E-PBT (expanded polybutylene terephthalate). In previous studies, sufficient time for polymer interdiffusion during molding is identified as crucial and requires adjusted crystallization kinetics. This study consequently examines to which extent the crystalline properties and the bead fusion behavior of E-PBT can be influenced by the bead foaming process. By varying the underwater granulation (UWG) water temperature, different cooling rates of the expanding melt are generated. The foamed beads show different cell morphologies, thermal and dynamic mechanical properties depending on the UWG water temperature. Those beads that show a pronounced shrinkage behavior in the thermomechanical analysis, caused by an increased open cell content and a pronounced cold-crystallization, exhibit a reduced bead fusion quality. The bead fusion quality is examined by the fracture surface. The shrinkage phenomenon causes a reduced bead to bead contact and partially separation between the beads.

The use of amine-based carbamates with their dual function, acting as amine curing agents and CO2 blowing agents after their decomposition without by-products, are promising for ecofriendly epoxy foams as high-performance materials. However, controlling cell morphology requires a proper adjustment of the viscosity at the foaming step. The viscosity is altered not only by blending neat amine and its derived carbamate at a fixed pre-curing time, but also by changing the pre-curing time at a fixed blend ratio. Within this study, diglycidylether of bisphenol A (DGEBA) epoxy resin is mixed with different blend ratios of isophorone diamine (IPDA) and its derived carbamate (B-IPDA). The systems are characterized by DSC and rheology experiments to identify the pre-curing effects on the derived epoxy foams. Epoxy foams at a blend ratio of 30/70w IPDA/B-IPDA showed the best foam morphology and an optimum Tg compared to other blend ratios. Furthermore, it was found that both pre-curing times, 2 h and 3 h, for the 30/70w IPDA/B-IPDA system reveal a more homogeneous cell structure. The study proves that the blending of neat amine and carbamate is beneficial for the foaming performance of carbamate systems.

With macroscopic litter and its degradation into secondary microplastic as a major source of environmental pollution, one key challenge is understanding the pathways from macro- to microplastic by abiotic and biotic environmental impact. So far, little is known about the impact of biota on material properties. This study focuses on recycled, bottle-grade poly(ethylene terephthalate) (r-PET) and the degrading enzyme PETase from Ideonella sakaiensis. Compact tension (CT) specimens were incubated in an enzymatic solution and thermally and mechanically characterized. A time-dependent study up to 96 h revealed the formation of steadily growing colloidal structures. After 96 h incubation, high amounts of BHET dimer were found in a near-surface layer, affecting crack propagation and leading to faster material failure. The results of this pilot study show that enzymatic activity accelerates embrittlement and favors fragmentation. We conclude that PET-degrading enzymes must be viewed as a potentially relevant acceleration factor in macroplastic degradation.

Reactive compounding of terminally phenolic OH-functionalized polycarbonate (PC) with epoxy-functionalized polymethylmethacrylate (PMMA) prepared by copolymerization with glycidyl methacrylate was investigated. It was spectroscopically demonstrated that a PC/PMMA copolymer was formed during the melt reaction of the functional groups. Zirconium acetylacetonate could catalytically accelerate this reaction. Correlations of the phenomenological (optical and mechanical) properties with the molecular level and mesoscopic (morphological) structure were discussed. By the investigated reactive compounding process, transparent PC/PMMA blends with two-phase morphologies were obtained in a continuous twin-screw extruder, which, for the first time, combined the high transmission of visible light with excellent mechanical performance (e.g., synergistically improved tensile and flexural strength and high scratch resistance). The transparency strongly depended on (a) the degree of functionalization in both PC and PMMA, (b) the presence of the catalyst, and (c) the residence time of the compounding process. The in-situ-formed PC/PMMA copolymer influenced the observed macroscopic properties by (a) a decrease in the interphase tension, leading to improved and stabilized phase dispersion, (b) the formation of a continuous gradient of the polymer composition and thus of the optical refractive indices in a diffuse mesoscopic interphase layer separating the PC and PMMA phases, and (c) an increase in the phase adhesion between PC and PMMA due to mechanical polymer chain entanglement in this interphase.

BACKGROUND: Charge storage capability is a fundamental property of polymers used in electromechanical transducer applications. In this work, the charge retention of ternary blends of poly(phenylene ether) and polystyrene modified with poly(styrene-co-acrylonitrile), polystyrene-block-poly(ethylene-co-butylene)-block-polystyrene or polystyrene-block-polyisobutylene-block-polystyrene (SIBS) triblock copolymers was correlated with the blend composition, final morphology and the chemical structure of the components. RESULTS: It was determined that the charge storage capability is favoured by a finely dispersed and non-interconnected phase and can be reduced by high polarity or low molecular weight of the blend components. Additionally, the molecular weight and the amount of styrene of the copolymers also determined the phase morphology, which in turn affected the charge retention. The use of SIBS for the ternary blends, especially in small quantities, significantly improved the charge storage. As such, 100 µm films with a surface potential of about 400 V were able to retain up to 240 V (60%) after 24 h at 130 °C. CONCLUSION: The electret behaviour of the polymer blends was influenced by a complex relationship between chemical structure, molecular weight and phase morphology. Copyright © 2009 Society of Chemical Industry

Due to the establishment of common thermoplastics such as polyethylene, polypropylene and polytetrafluoroethylene as substrates for modern electrets, research in this field has seen significant progress in recent decades. However, there still is a need for new substrate materials in order to boost modern-day electret applications. Important targets for a further development are electret substrates with a tailored balance between cost and performance especially at elevated temperatures. In this study, experimental results concerning the charge storage behaviour of poly(2,6-dimethyl-1,4-phenylene ether) (PPE) films and its blends with polystyrene (PS) are presented. As demonstrated, the good electret performance of neat PPE can be further enhanced by the addition of suitable weight fractions of PS, a synergistic electret behaviour that is related to morphological blend parameters such as the packaging density and the presence of PS micro-heterogeneities in the PPE/PS matrix. Most importantly, the results highlighted in this study clearly demonstrate the potential of blending as a promising approach towards satisfying the demands of tomorrows’ electret applications.

The mechanical performance of immiscible blends of poly(2,6-dimethyl-1,4-phenylene ether) (PPE) and poly(styrene-co-acrylonitrile) (SAN) and the subsequent influence of compatibilisation by tailored polystyrene-block-polybutadiene-block-poly(methyl methacrylate) triblock terpolymers (SBM) on the mechanical performance under static and dynamic loads is analysed in detail. A PPE/SAN 60/40 blend was selected as a base system for the compatibilisation experiments. The observed static tensile behaviour is described by micromechanical models and correlated to the blend microstructures as observed by transmission electron microscopy. In most cases, the addition of the SBM triblock terpolymers further enhances the ductility of the blend while only leading to a minor reduction of modulus and strength. Triblock terpolymers with symmetric end blocks, mainly located at the interface between PPE and SAN, led to nearly isotropic specimens. In contrast, SBM materials with a longer polystyrene block predominantly formed micelles in the PPE phase and the blends revealed a highly anisotropic morphology. Comparative investigations of the fatigue crack growth behaviour parallel to the direction of injection also reflected this variation in mechanical anisotropy of the compatibilised blends. A poor toughness and a predominant interfacial failure were observed in the case of the SBM with a long polystyrene block. In contrast, a considerable improvement in properties as a result of pronounced plastic deformations was observed for blends compatibilised by triblock terpolymers with symmetric end blocks. The systematic correlation between morphology and mechanical performance of compatibilised PPE/SAN blends established in this study provides an efficient way for the desired selection of suitable and effective compatibilising agents, ensuring both a superior multiaxial toughness as well as a high strength and modulus of the overall system.

Immiscible blends of poly(2,6-dimethyl-1,4-phenylene ether) (PPE) and poly(styrene-co-acrylonitrile) (SAN) with a weight composition of 60/40 were compatibilised by polystyrene-block-polybutadiene-block-poly(methyl methacrylate) triblock terpolymers (SBM) using a two-stage melt-processing approach. In order to investigate the influence of the SBM composition on the compatibilisation efficiency, the block lengths of the triblock terpolymers were systematically varied. The resulting morphological features of the blend systems as function of SBM composition and processing parameters are correlated with the resulting thermal and thermo-mechanical properties. In the ideal case, SBM should be located at the interface as PS is miscible with PPE while PMMA is miscible with SAN. The elastomeric middle block as an immiscible component should remain at the interface. This particular morphological arrangement is known as the ‘raspberry morphology’. A detailed TEM analysis of the blend morphologies following initial extrusion-compounding revealed a high compatibilisation efficiency of the SBM types with equal lengths of the end blocks and, furthermore, the desired raspberry morphology was achieved. In contrast, high PS contents in comparison to the other blocks led to a pronounced micelle formation in the PPE phase. Further evaluation of the blend structures following injection-moulding indicated that the morphologies remain relatively stable during this second melt-processing step. A detailed thermal analysis of all blend systems supports the interpretation of the observed morphological features. The fundamental correlation between SBM composition and blend morphology established in this study opens the door for the controlled development of interfacial properties of such compatibilised PPE/SAN blends during melt-processing.

The foaming behaviour of polymer blends was systematically investigated using carbon dioxide as a blowing agent. Two batch-processing techniques were used to prepare specimens of different size. Various binary mixtures over a wide compositional range were selected as reference materials, in particular including immiscible (poly(2,6-dimethyl-1,4-phenylene ether)/poly(styrene-co-acrylonitrile) (PPE/SAN) blends. Moreover, the influence of a compatibilization with block copolymers was investigated for PPE/SAN blends. The resulting foam morphology was characterised by evaluating the density, the cell size distribution, the cell wall morphology and the compression behaviour. Besides the commonly accepted key criteria for foaming neat polymers, our study identified significant factors determining the foamability of blends such as the blend morphology, the rheological and the thermal properties. Interestingly, the compatibilization of these PPE/SAN blends by block copolymers was identified as a technique to establish micro- and submicrocellular foam morphologies with nanostructured cell walls. In view of these results, new pathways for the tailoring of cellular materials are derived.