Search

The influence of radical-disulfide exchange on the polymerization and relaxation dynamics of thiol–ene–disulfide networks is investigated.

The macroscopic alignment of the nematic director within liquid crystalline elastomers (LCEs) amplifies the magnitude of the directional strain response. Theory predicts that the stimuli response o...

The kinetic effects of the substitution and functionality of the thiol in thiol-Michael reactions were investigated using model monofunctional thiols and multifunctional thiols used in various cros...

This article describes an efficient enamine organocatalyzed thiol-Michael click reaction and its broad application in cross-linking polymerizations. A series of enamines was shown to catalyze the t...

Thermoplastics encompass the majority of commercial plastics but are limited to manufacturing techniques that require heat and/or solvent to enable material reprocessing and reshaping. Photopolymer...

Photomechanical effects in liquid crystal elastomers (LCEs) functionalized with photochromic moieties, such as azobenzene, have been widely studied. This prior work has demonstrated that isothermal, photoinduced (e.g. phototropic) disruption of order via isomerization of azobenzene affects the anisotropic chain configurations of the polymer network. Here, we examine the contribution of the strength of intermolecular interactions between polymer chains in the LCE to both the thermotropic and phototropic response. By incorporating liquid crystalline monomers with reduced aromatic content, both the temperature and irradiation conditions to induce mechanical response are reduced.

Controlling the microstructure of heterogeneous, polymer membranes used in gas barrier and gas separation technologies is challenging. Being able to control composite structures is beneficial to achieve an optimum combination of gas permeation and mechanical performance. In addition, unique properties such as anisotropy and confined transport can be controlled by tailoring the size and position of constituent materials. Two-stage reactive polymer (TSRP) networks are an emerging dual-cure polymer material for spatially varying cross-linking density via photopatterning. In this work a thiol–acrylate-based TSRP was used to investigate the effects of pattern geometry on CO₂ permeability and mechanical properties. Line and square patterns of alternating high and low cross-linking density, with characteristic dimension between 1 mm and 10 μm, were generated in TSRP membranes. Notably, synergistic enhanced barrier properties were observed for 10 μm square patterns of lower cross-linking density (or higher permeability) material exhibiting two confined dimensions compared to line gratings with only one confined dimension.

In the present work, the photocatalytic activity was investigated toward a thiol-Michael reaction of different combinations of 9-fluorenylmethyl carbamate (Fmoc) derivatives and photocaged amines (PCA) as base amplifiers and the catalytic base, respectively. This phototriggering approach was systematically studied for evaluating its effect on kinetics between thiol and Michael acceptors like acrylate or sulfone wherein, butyl 3-mercaptopropionate (BMP), 1-hexyl acrylate (HA), and ethyl vinyl sulfone (EVS) were used as model reactants. Interestingly, PCAs exhibited low quantum yields by themselves; NPPOC-Hex (2.5 mol %) which when used with BMP and HA, resulted in only 25% thiol conversion; however, when used along with Fmoc-Hex or Fmoc-TMG (2.5 or 5 mol %), it resulted in a higher thiol conversion of 50–60%. Furthermore, use of NPPOC-DEA (5 mol %) with 1 mol % Fmoc-TMG resulted in >70% thiol conversion for the same system. Upon using BMP and EVS nearly complete conversion of functional groups with 5 mol % NPPOC-DEA and 5 mol % Fmoc-DEA was obtained. This enhancement in reaction kinetics and conversion upon addition of an Fmoc derivative to a monofunctional thiol-Michael system was extended to multifunctional derivatives for polymerizing cross-linked polymer networks. Moreover, the kinetic study on model reactants also demonstrated efficient dark curing, resulting in 50–75% thiol conversion with only 30 s irradiation time, leading to validation of the efficacy of Fmoc derivatives and PCAs as photocatalysts for dark cure. Upon precise characterization in cross-linked systems using Raman spectroscopy for TMPTA/PETMP in the presence of 20 mol % NPPOC-DEA and 1 mol % Fmoc-TMG, the extent of dark cure was evaluated for a distance of 16.5 mm, which was observed to undergo maximum conversion and high dark cure propagation upon heating to 70 °C. Therefore, Fmoc-PCA catalysis is a practically useful approach for improving the photoinitiated efficiency of the thiol-Michael reaction and enabling photopolymerization in the dark with a marked improvement in photosensitivity.

The effect of thiol substitution in radical thiol–ene reactions has been studied by using model, monofunctional thiols as well as multifunctional thiol monomers along with the assessment of their subsequent polymerization reactions and polymer mechanical behavior. FT-IR was used to monitor the polymerization rate and quantify the overall conversion. While the total conversion was observed to range from 70% to 100%, the polymerization rate was found to decrease by as much as 10-fold as the thiol substitution was changed from primary to tertiary. Analogous multi-thiol monomers of similar structure but varying substitution were synthesized to observe the effect of substitution type on polymerization kinetics and polymer behavior. Methylation at the α-carbon was varied from primary to tertiary to observe these differences. Mechanical properties were assessed by using dynamic mechanical analysis and water sorption experiments, where the glass transition temperatures were found to be within 1–2 °C as thiol substitution varied. Furthermore, primary thiol films absorbed 1–3% more water than secondary thiol films. Resin shelf stability experiments were performed by using rheometry to measure storage time-dependent viscosity changes, and it was found that secondary thiol films remained relatively stable for up to 100 times longer than their primary counterparts. It was concluded that while there are differences under relatively slow initiation conditions, at typical initiation rates all three thiol substitutions may be made to react at similar rates for both monofunctional and polymeric systems.

The unique photodynamics of aromatic thiols (relative to alkyl thiols) allowed their employment as effective ultraviolet and visible light photoinitiators (PIs) for acrylate photopolymerizations, r...

Functional nanogels are attractive additives for use in polymer composites. In this study, nanogels with internal allyl sulfide moieties throughout their network structure were prepared via a thiol-Michael addition reaction. The excess thiol-functionalized nanogels were less than 60 nm as discrete particles but act as room-temperature liquids in the bulk state. The reactive nanogels can be dispersed in and swollen by a thiol-ene matrix resin, which upon photopolymerization yields dramatically decreased levels of polymerization shrinkage stress. Furthermore, the postcured nanogel-modified polymers effectively relaxed applied stresses as well as enhanced toughness during exposure to a UV light source that activated the addition-fragmentation as a means for dynamic bond exchange. These nanogels provide a generic approach to introduce adaptable network performance that significantly improves a number of key properties of glassy cross-linked polymer.

Because of facile implementation, quantitative conversions, and an insensitivity to oxygen, water, and most organic functional groups, radical-mediated thiol-ene coupling (TEC) reactions have emerged as a valuable tool in macromolecule synthesis. It was recently demonstrated that the kinetics and conversions of thiyl radical-mediated reactions are adversely affected in the presence of basic amines by the formation of retardive thiolate anions. Herein, the performance of TEC polymerizations is evaluated under a variety of reaction environments with the intention to aid in the optimal formulation design of TEC reactions in the presence of amines. Results from both bulk and aqueous-phase network photopolymerizations established that sensitivity to amine basicity and pH is dependent on the thiol acidity, although norbornene-type alkenes exhibit a unique ability to achieve high conversions, where allyl ethers, vinyl ether, and vinyl siloxanes are highly inhibited. Additionally, the protic solvents such as alcohols and acetic acid are established as ideal solvents or additives to suppress or eliminate amine-induced retardation.

Motivated by the various reported potential applications of poly(phosphine oxide) materials, a visible light photoinitiated iodo-ene reaction was successfully employed in network polymerization between the phosphorus-containing multifunctional monomer, tris(allyloxymethyl)phosphine oxide (TAOPO), and diiodoperfluorobutane. The cross-linked poly(phosphine oxide) network exhibited a higher glass transition temperature than a similarly cross-linked polymer formulated with trimethylolpropane triallyl ether (TMPTAE). Interestingly, the TMPTAE/DIPFB cross-linked polymer, changed color from clear to yellow within 10 min of exposure to air, whereas the cross-linked poly(phosphine oxide) underwent a similar change only upon heating. Upon investigation, it was determined that alkenes were generated within the polymer network, presumably via elimination, accounting for the observed color. These double bonds, formed in the polymer matrix, permitted surface modification via radical thiol-ene reaction. The successful surface functionalization with PEG-SH resulted in increasing the surface wettability. Additionally, the phosphorus-containing network polymer with double bonds in the polymer matrix showed shape memory capability, this representing an exciting and versatile materials platform.

A new group of nitrogen-centered nucleophilic catalysts for the thiol-Michael addition “click” reactions is examined. These nucleophiles showed efficient catalytic activities as compared with traditional base catalysts, such as triethylamine, and are demonstrated to be a viable strategy for cross-linking polymerization reactions. Additionally, an experimental and computational mechanistic study was performed, suggesting a pathway for the nitrogen-centered catalyst to undergo the nucleophilic addition mechanism.

A visible-light base generating system was successfully employed in catalyzing the thiol-Michael addition reaction to yield cross-linked polymers from a stoichiometric mixture of model thiol and vinyl monomers. Implementation of the radical inhibitor TEMPO with a combination of a photosensitizer (isopropylthioxanthone, ITX) and a photobase generator (triazabicyclodecene tetraphenylborate, TBD·HBPh4) resulted in suppression of radical mediated side reactions and provided stoichiometric and complete conversion of both thiol and vinyl functional groups. The new initiating system acts as an efficient visible-light photobase generator that improves the orthogonality of the thiol-Michael addition with respect to off-stoichiometric radical thiol-vinyl addition/vinyl chain reactions. This approach opens up a variety of possibilities for base-catalyzed reactions in multiple applications such as coatings and biomaterials that require biocompatible, environmentally friendly, and low-energy visible-light initiation.

A photoinitiation system that utilizes phosphonium tetraphenylborate as the key component was developed for the visible light-triggered nucleophile-catalyzed thiol-Michael addition reaction. This highly reactive catalyst was composed of a photocaged phosphine (methyldiphenylphosphonium tetraphenylborate, MDPP·HBPh

An approach to efficient and scalable production of oligonucleotide-based gel networks is presented. Specifically, a new class of xenonucleic acid (XNA) synthesized through a scalable and efficient thiol–ene polymerization mechanism, “clickable” nucleic acids (CNAs), were conjugated to a multifunctional poly(ethylene glycol), PEG. In the presence of complementary single stranded DNA (ssDNA), the macromolecular conjugate assembled into a crosslinked 3D gel capable of achieving storage moduli on the order of 1 kPa. Binding studies between the PEG-CNA macromolecule and complementary ssDNA indicate that crosslinking is due to the CNA/DNA interaction. Gel formation was specific to the base sequence and length of the ssDNA crosslinker. The gels were fully thermoreversible, completely melting at temperatures above 60 °C and re-forming upon cooling over multiple cycles and with no apparent hysteresis. Shear stress relaxation experiments revealed that relaxation dynamics are dependent on crosslinker length, which is hypothesized to be an effect of the polydisperse CNA chains. Arrhenius analysis of characteristic relaxation times was only possible for shorter crosslinker lengths, and the activation energy for these gels was determined to be 110 ± 20 kJ mol−1. Overall, the present work demonstrates that CNA is capable of participating in stimuli-responsive interactions that would be expected from XNAs, and that these interactions support 3D gels that have potential uses in biological and materials science applications.

Dynamic photopolymer networks that take advantage of the thermodynamically controlled reversibility of thiol–succinic anhydride adducts were synthesized from commercial substrates and investigated as a new class of covalent adaptable networks (CANs). Through systematic studies of the catalyst and stoichiometry effects on the exchange dynamics two distinctive exchange mechanisms were found, and then demonstrated to contribute to the overall dynamic characteristics. By varying the catalyst activity, i.e. basicity and/or nucleophilicity, control over the dynamic responsiveness through changes in the type of dynamic covalent chemistry mode (reversible addition vs. reversible exchange) was achieved in otherwise compositionally analogous materials. More specifically, the participation of the associative mechanism (thiol–thioester exchange) in the otherwise dissociative networks, and its relevance on materials properties was demonstrated by dielectric analysis (DEA) and dynamic mechanical analysis (DMA). The activation energies (Ea) for viscous flow obtained from DMA stress relaxation experiments and from dielectric modulus and loss crossover points were shown to match well between the two techniques. The Ea in stoichiometric systems was found to be 110–120 kJ mol−1, whereas 50% excess thiol systems were characterized by Ea ranging 95–105 kJ mol−1. The thermodynamic equilibrium conversion, estimated in the temperature controlled FTIR, for a stoichiometric 3-mercaptopropionate-succinic anhydride combination was determined at 92 ± 1% at ambient temperature, and decreased to 67 ± 1% at 120 °C within one hour of equilibration time (ΔH° = −46 ± 5 kJ mol−1). Such high potential for reversibility of the thioester anhydride linkages resembles maleimide-furan Diels–Alder networks but has many other attributes that make these CANs of unprecedented value in fundamental research on dynamic materials.

Recycling of polyurethanes is largely infeasible due to the harsh reprocessing conditions and associated risks of side reactions and degradation whereas polymer networks incorporating dynamic covalent bonds represent an attractive approach to the design of recyclable materials. Here, we report findings on the dynamic nature of thiourethanes, and their application as a new class of recyclable analogs of urethane materials. A series of small molecule experiments was initially conducted to determine the equilibrium constant and exchange reaction kinetic constant for the thiol–isocyanate reaction. Furthermore, incorporating those thiourethane moieties into a cross-linked network resulted in thermoset materials that are readily depolymerized to liquid oligomers. The resultant oligomers can be re-crosslinked to thiourethanes without any loss of performance nor change in mechanical properties (peak stress of 25 MPa with max strain of 200%). Moreover, the recycled thiol oligomers from thiourethane network polymers could potentially be transformed into other materials with mechanical properties that exceed those of the initial, pristine thiourethane materials. Overall, the ease with which these polythiourethanes are polymerized, recycled and reformulated gives a new direction and hope in the design of sustainable polymers.

Photopolymerizable semicrystalline thermoplastics resulting from thiol-ene polymerizations were formed via fast polymerizations and achieved excellent mechanical properties. These materials have been shown to produce materials desirable for additive manufacturing (3D printing), especially for recyclable printing and investment casting. However, while well-resolved prints were previously achieved with the thiol-ene thermoplastics, the remarkable elongation at break (ϵ(max)) and toughness (T) attained in bulk were not realized for 3D printed components (ϵ(max,bulk) ~ 790%, T(bulk) ~ 102 MJ m(−3) vs. ϵ(max,print) < 5%, T(print) < 0.5 MJ m(−3)). In this work, small concentrations (5–10 mol%) of a crosslinker were added to the original thiol-ene resin composition without sacrificing crystallization potential to achieve semicrystalline, covalently crosslinked networks with enhanced mechanical properties. Improvements in ductility and overall toughness were observed for printed crosslinked structures, and substantial mechanical augmentation was further demonstrated with post-manufacture thermal conditioning of printed materials above the melting temperature (T(m)). In some instances, this thermal conditioning to reset the crystalline component of the crosslinked prints yielded mechanical properties that were comparable or superior to its bulk counterpart (ϵ(max) ~ 790%, T ~ 95 MJ m(−3)). These unique photopolymerizations and their corresponding monomer compositions exhibited concurrent polymerization and crystallization along with mechanical properties that were tunable by changes to the monomer composition, photopolymerization conditions, and post-polymerization conditioning. This is the first example of a 3D printed semicrystalline, crosslinked material with thermally tunable mechanical properties that are superior to many commercially-available resins.

Due to a mismatch in mechanical moduli, the interface between constituent materials in a composite is the primary locus for crack nucleation due to stress concentration. Relaxation of interfacial stresses, without modifying the properties of constituent materials, is a potent means of improving composite performance with broad appeal. Herein, we develop a new type of adaptive interface that utilizes thiol–thioester exchange (TTE) at the filler–polymer interface. Specifically, dynamic covalent bonds sequestered at material interfaces are reversibly exchanged in the presence of thioester moieties, excess thiol and a base/nucleophile catalyst. Employing this active interface effectively mitigates deleterious growth of interfacial stresses, thereby enhancing the composite's mechanical performance in terms of reductions in polymerization shrinkage stress and improvement in toughness. Activating interfacial TTE in an otherwise static matrix resulted in 45% reduction in the polymerization stress, more significant post-polymerization stress relaxation and drastically increased toughness relative to control composites incapable of TTE bond exchange but otherwise identical. In particular, the higher fracture toughness in TTE-activated composites is attributed to the alleviation of crack tip strain concentration, as revealed by digital image correlation.

Thermally transformable/responsive (meth)acrylate photopolymer networks were constructed from commercial (meth)acrylate esters and synthetic di- and mono(meth)acylate monomers bearing thioester functionalities. The thermal responsiveness, here self-limited exchange, relied on the catalytic metamorphosis of thioesters into esters with the concomitant depletion of hydroxyls and subsequent generation of free thiols. The thioester–hydroxyl cross-exchange was demonstrated in network systems with interchain thioesters as well as in networks with side-chain pendant thioacetyls. The interchain metamorphosis resulted in close to 80% conversion of thioesters into esters when 2 equiv of hydroxyl groups was initially present. In practical terms, such an outcome enabled efficient stress relaxation (60%) and good shape adaptation (90% shape fixity) in 1 h at 105 °C. On the other hand, side-chain S → O acyl transfer reactions were found to vary in efficiency depending on the vicinity of thioesters and hydroxyls. When in...

Free-radical polymerizations are used for a wide range of applications but are detrimentally impacted by the presence of oxygen. Zinc phthalocyanines have been previously used as singlet oxygen generators to excite radical-consuming ground-state triplet oxygen into its less reactive singlet state prior to photoexcitation of a photoinitiator. We report for the first time that polymerization can be achieved via irradiation of UV band of phthalocyanine and that photosensitization and photoinitiation can be independently achieved via irradiation of its two distinct absorption bands to reduce oxygen inhibition and initiate polymerization without the need for additional treatment. We propose a mechanism for this unique photoinitiation phenomenon and verify its feasibility via computational and experimental approaches. This new class of dual-photosensitive molecules shows promising utility in applications that are adversely impacted by the presence of oxygen, such as coatings and stereolithography.

A combined experimental and computational study of the reactivities of seven commonly used Michael acceptors paired with two thiols within the framework of photobase-catalyzed thiol-Michael reactions is reported. The rate coefficients of the propagation (k(P)), reverse propagation (k(−P)), chain-transfer (k(CT)), and overall reaction (k(overall)) were experimentally determined and compared with the well-accepted electrophilicity parameters of Mayr and Parr, and DFT-calculated energetics. Both Mayr’s and Parr’s electrophilicity parameters predict the reactivities of these structurally varying vinyl functional groups well, covering a range of overall reaction rate coefficients from 0.5 to 6.2 s(−1). To gain insight into the individual steps, the relative energies have been calculated using DFT for each of the stationary points along this step-growth reaction between ethanethiol and the seven alkenes. The free energies of the individual steps reveal the underlying factors that control the reaction barriers for propagation and chain transfer. Both the propagation and chain transfer steps are under kinetic control. These results serve as a useful guide for Michael acceptor selection to design and predict thiol-Michael-based materials with appropriate kinetic and material properties

In the present study, the photo-initiated copper-catalyzed azide-alkyne cycloaddition (CuAAC) polymerization was utilized to form structurally diverse glassy polymer networks. Systematic alterations in the monomer backbone rigidity (e.g., cyclic or aliphatic groups with a different length of backbone) and the reactive functional group density (e.g., tetra-, tri-, di-, and mono-functional azide and alkyne monomers) were used to provide readily tailorable network structures with crosslink densities (estimated from the rubbery modulus) varying by a factor of over 20. All eight of the resultant networks exhibited glass transition temperatures (T(g)) between 50 and 80 °C with tensile toughness ranging from 28 to 61 MJ m(−3). A nearly linear dependence of yield stress and elongation at break (broadly defined as strength and ductility, respectively) on the T(g) and rubbery modulus was established in these triazole networks. When a flexible di-alkyne monomer (5 carbon spacing between alkynes) was incorporated in a network composed of a tri-alkyne and di-azide monomer, the elongation at break was improved from 166 to 300 %, while the yield stress was reduced from 36 to 23 MPa. Additionally, the polymer ductility was also varied by incorporating mono-functional azides as chain ends in the network - replacing a sterically hindered stiff mono-azide with a more flexible mono-azide increased the elongation at break from 24 to 185 % and the tensile toughness from 6 to 28 MJ m(−3).

International audience; Surface modifications are typically permanent in shape and chemistry. Herein, vinylogous urethane (VU) chemistry is presented as an easily accessible and versatile platform for rapid, facile, and reworkable surface modification. It is demonstrated that both physical and chemical post-modification of permanent, yet dynamic elastic polymer networks are achieved. Surface patterns with high regularity are created, both via a straightforward replication process using a polydimethylsiloxane stamp (resolution ca. 10-100 µm) as well as using thermally activated nano-imprint lithography (NIL) to form hole, pillar, or line patterns (ca. 300 nm) in elastic VU-based vitrimers. The tunable, rapid exchange allows patterning at 130 °C in less than 15 min, resulting in an increased water contact angle and surface-structure induced light reflection. Moreover, it is also demonstrated that the use of a single dynamic covalent chemistry makes it possible to strongly adhere to fluorinated and non-fluorinated materials based on incompatible matrices, causing cohesive failure in a peel test. In a topography scan, the visibly transparent interface is shown to possess a continuous phase without a gap, while maintaining distinctively separated (non)-fluorinated domains. Finally, this approach allowed for a straightforward coating of a non-fluorinated material with a fluorinated monomer to minimize the overall fluorinated content.

Through thiol-ene photopolymerization of presynthesized oligomers, advanced clickable nucleic acids (CNA-2G) are synthesized with sequence-controlled repeating units. As examples, poly(thymine-adenine) (polyTA) CNA-2G and poly(thymine-thymine-cytosine) CNA-2G are synthesized by polymerizing thiol-ene heterofunctional dimers with pendant thymine-adenine nucleobases and trimer with pendant thymine-thymine-cytosine nucleobases. Based on size exclusion chromatography (SEC) analysis, polyTA and polyTTC have number average molecular weights of 2000 and 1800, respectively, which contain 7-8 pendant nucleobases. Based on the different behavior of the CNA-2G monomers and CNA-2G oligomers with two or more pendant nucleobases in photopolymerization, an unusual thiol-ene chain-growth propagation mechanism is observed for the former and a common thiol-ene step-growth propagation mechanism for the latter. The uncommon thiol-ene chain-growth propagation is hypothesized to rely on a six-membered ring mediated intramolecular hydrogen atom transfer process.

Despite the powerful nature of the aza-Michael reaction for generating C–N linkages and bioactive moieties, the bis-Michael addition of 1° amines remains ineffective for the synthesis of functional, step-growth polymers due to the drastic reduction in reactivity of the resulting 2° amine mono-addition adduct. In this study, a wide range of commercial hydrazides are shown to effectively undergo the bis-Michael reaction with divinyl sulfone (DVS) and 1,6-hexanediol diacrylate (HDA) under catalyst-free, thermal conditions to afford moderate to high molecular weight polymers with M(n) = 3.8–34.5 kg mol(-1). The hydrazide-Michael reactions exhibit two distinctive, conversion-dependent kinetic regimes that are 2(nd)-order overall, in contrast to the 3(rd)-order nature of amines previously reported. The mono-addition rate constant was found to be 37-fold greater than that of the bis-addition at 80 °C for the reaction between benzhydrazide and DVS. A significant majority (12 of 15) of the hydrazide derivatives used here show excellent bis-Michael reactivity and achieve >97% conversions after 5 days. This behavior is consistent with calculations that show minimal variance of electron density on the N-nucleophile among the derivatives studied. Reactivity differences between hydrazides and hexylamine are also explored. Overall, the difference in reactivity between hydrazides and amines is attributed to the adjacent nitrogen atom in hydrazides that acts as an efficient hydrogen-bond donor that facilitates intramolecular proton-transfer following the formation of the zwitterion intermediate. This effect not only activates the Michael acceptor but also coordinates with additional Michael acceptors to form an intermolecular reactant complex.

Here, a process is introduced for forming dual stage thiol-Michael/acrylate hybrid networks photocured by two different wavelengths, demonstrating its use in nanoimprint lithography (NIL) and shape memory materials. Initiated with a visible light sensitive photobase and a UV-sensitive radical initiator, thiol-Michael-acrylate hybrid polymerizations were programmed to proceed sequentially and orthogonally, with base-catalyzed thiol-Michael photopolymerization as the first stage and radical mediated acrylate photopolymerization as the second stage. By regulating the photopolymerization formulations, i.e. thiol-to-acrylate ratios, initiator loadings and irradiation conditions, a series of materials with highly tunable mechanical performance was achieved, with ultimate T(g) values ranging from 23 to 70 °C. With a photopatternable first stage and a readily reconfigurable second stage, its implementation in nanoimprint lithography (NIL) enabled surface features on the scale of 10 nm to be formed on a photopatterned substrate. Additionally, the dual stage polymer results in a relatively homogenous polymer network with a narrow glass transition temperature (Tg), which enables rapid response in applications as shape memory materials, with shape-fixity values above 95% and shaperecovery values above 99%. With its unique photocuring process and programmable mechanical properties, the two color light controlled photopolymerization can be exploited as a useful tool in a wide range of materials science applications.

Polymers that possess dynamic covalent bonds activated at ambient conditions are ideal platforms for smart, responsive materials. Herein, a class of dynamic covalent polymerizations is developed based on the thiol-thioester exchange, that is, transthioesterification, reaction. Shifts in the equilibrium extent of the exchange reactions are deliberately utilized to drive the formation of oligomers and polymers. In particular, a series of AB and A

Kinetic parameters and their influence on the overall rates of base-catalyzed thiol–Michael reactions proceeding via an alternating propagation and chain transfer cycle were evaluated. A kinetic model was developed that enables the determination and accurate prediction of the reaction kinetic paths for the thiol–Michael addition reaction and its accompanying polymerization. Individual kinetic parameters for propagation and chain transfer steps were evaluated for three commonly used thiol and vinyl functional monomers. Chain transfer and propagation kinetic parameters were determined in binary combinations of monomers from analysis of experimental data for the reaction rates. Subsequently, eight ternary thiol–Michael systems composed of thiol–acrylate–vinyl sulfone and thiol 1-thiol 2-vinyl were analyzed based on the binary kinetic model parameters. It was clearly demonstrated that the kinetic parameters determined from the binary reactions enabled an accurate prediction of the relative reactivity and sele...

This work details a novel polyurethane liquid crystal elastomer (PULCE) with exchangeable carbamate functional groups that enable programming of a uniformly aligned monodomain sample through the ap...

In this contribution, three o-nitrobenzyl-based photobase systems were synthesized and evaluated for visible light initiated thiol-Michael addition polymerizations. With a modified structure, the (3,4-methylenedioxy-6-nitrophenyl)-propyloxycarbonyl (MNPPOC) protected base performance exceeds that of the nonsubstituted 2-(2-nitrophenyl)-propyloxycarbonyl (NPPOC) protected base and an ITX sensitized photobase system, with respect to both long-wavelength light sensitivity and photolytic efficiency. In material synthesis, MNPPOC-TMG is capable of initiating photo thiol-Michael polymerization efficiently and orthogonally with only limited visible light exposure and generating a highly homogeneous cross-linked polymer network. This approach enables the thiol-Michael “click” reaction to be conducted with a low-energy, visible light irradiation and, thus, expands its applications in biocompatible and UV sensitive materials.

The effect of amines on the kinetics and efficacy of radical-mediated thiol-ene coupling (TEC) reactions was investigated. By varying the thiol reactant and amine additive, it was shown that amines retard thiyl radical-mediated reactions when the amine is adequately basic enough to deprotonate the thiol affording the thiolate anion, e.g., when the weakly basic amine tetramethylethylenediamine was incorporated in the TEC reaction between butyl 2-mercaptoacetate and an allyl ether at 5 mol %, the final conversion was reduced from quantitative to

The synthesis, characterization, and post-synthetic functionalization of a readily functionalized step-growth linear polymer derived from divinyl sulfone (DVS) and tert-butylcarbazate (TBC) is presented. Construction of this atom-economic polymer under thermal conditions proceeds in high yield (>94%) at 75 °C, achieving a number average molecular weight of 17.0 kDa, a weight-average molecular weight of 26.2 kDa, and a polydispersity of 1.54, corresponding to a number-average degree of polymerization >60, despite the step-growth nature of the reaction. Removal of the Boc-groups yields a polymeric scaffold with hydrazine moieties that are readily reacted with aldehydes to yield the corresponding functional polyhydrazone materials. A variety of hydrazone-linked functionalities are readily added under mild conditions, including cationic, anionic, electron-rich/poor, and hetereoatom-containing aromatics. Owing to its rapid functionalization and simple and scalable synthesis, this material is an accommodating and generalized polymer scaffold that is rapidly tailored to a variety of applications with easily introduced functionality.

This study is the first to employ the use of the copper-catalyzed azide-alkyne cycloaddition (CuAAC) polymerization to form a tough and stiff, porous material from a well-defined network possessing a high glass transition temperature. The effect of the network linkages formed as a product of the CuAAC reaction, i.e., the triazoles, on the mechanical behavior at high strain was evaluated by comparing the CuAAC foam to an epoxy-amine-based foam, which consisted of monomers with similar backbone structures and mechanical properties (i.e., Tg of 115 °C and a rubbery modulus of 1.0 MPa for the CuAAC foam, Tg of 125 °C and a rubbery modulus of 1.2 MPa for the epoxy-amine foam). When each foam was compressed uniformly to 80% strain at ambient temperature, the epoxy-amine foam was severely damaged after only reaching 70% strain in the first compression cycle with a toughness of 300 MJ/m3. In contrast, the CuAAC foam exhibited pronounced ductile behavior in the glassy state with three times higher toughness of 850 MJ/m3 after the first cycle of compression to 80% strain. Additionally, when the CuAAC foam was heated above Tg after each of five compression cycles to 80% strain at ambient temperature, the foam completely recovered its original shape while exhibiting a gradual decrease in mechanical performance over the multiple compression cycles. The foam demonstrated almost complete shape fixity and recovery ratios even through five successive cycles, indicative of “reversible plasticity”, making it highly desirable as a glassy shape memory foams.

The exchange of thiolates and thiols has long been held as a nearly ideal reaction in dynamic covalent chemistry. The ability for the reaction to proceed smoothly in neutral aqueous media has propelled its widespread use in biochemistry, however, far fewer applications and studies have been directed towards its use in material science which primarily is performed in organic media. Herein, we present the exploration of this dynamic exchange in both small molecule and polymer settings with a wide sampling of thiols, thioesters, organic bases, and nucleophilic catalysts in various organic solvents. Effects of the character of the thiol and thioester, pKa or nucleophilicity of the catalyst, and heat on the reaction were investigated. The mechanism regarding the previously unexplored effectiveness of nucelophilic catalysts, such as quinuclidine or DABCO, to affect the thiol-thioester exchange was also explored. Finally, the use of the thiol-thioester exchange in a network polymer to reduce applied stresses or change shape of the material following polymerization was shown and the ability of basic and nucleophilic catalysts to promote these effects were benchmarked. The influence of polarity in these networks was also explored, with the rate of exchange shown to be easily tuned by the addition of diluents with varying polarities. Presented here is a so-called “user's guide” to the thiol-thioester exchange; we hope that this guide is instructive to practitioners in the field of material science which seek to utilize the thiol-thioester exchange in both linear and network polymers.

Of importance for adhesive materials, particularly pressure-sensitive adhesive (PSA) systems, is the ability to increase bulk toughness without reduction of adhesion. Previous approaches for increasing PSA durability sacrifice permanent cross-linking or adhesive potential, limiting performance. In this work, covalent adaptable networks (CANs) derived from thiol-thioester exchange (TTE) are utilized as a basis for adhesive films. Tensile and single-lap shear tests were conducted for adhesive materials containing no filler, 15 wt % nanoparticles functionalized with thioester-containing acrylate, or 15 wt % nanoparticles functionalized with nonthioester-containing acrylate. Additionally, fatigue experiments were conducted on unfilled adhesives. Results indicate that TTE improves toughness, adhesion, and fatigue in unfilled materials. Filled adhesives with activated TTE showed a nearly fourfold increase in adhesion with slightly reduced toughness compared to uncatalyzed filled specimens. This work has implications in many industries, from biomedical to automotive, as toughness and fatigue resistance are important considerations for adhesive applications.