Search

The Extreme Ultraviolet Imager (EUI) instrument for the Solar Orbiter mission will image the solar corona in the extreme ultraviolet (17.1 nm and 30.4 nm) and in the vacuum ultraviolet (121.6 nm). It is composed of three channels, each one containing a telescope. Two of these channels are high resolution imagers (HRI) at respectively 17.1 nm (HRI-EUV) and 121.6 nm (HRI-Ly∝), each one composed of two off-axis aspherical mirrors. The third channel is a full sun imager (FSI) composed of one single off-axis aspherical mirror and working at 17.1 nm and 30.4 nm alternatively. This paper presents the optical alignment of each telescope. The alignment process involved a set of Optical Ground Support Equipment (OGSE) such as theodolites, laser tracker, visible-light interferometer as well as a 3D Coordinates Measuring Machine (CMM). The mirrors orientation have been measured with respect to reference alignment cubes using theodolites. Their positions with respect to reference pins on the instrument optical bench have been measured using the 3D CMM. The mirrors orientations and positions have been adjusted by shimming of the mirrors mount during the alignment process. After this mechanical alignment, the quality of the wavefront has been checked by interferometric measurements, in an iterative process with the orientation and position adjustment to achieve the required image quality.

The Extreme Ultraviolet Imager (EUI) instrument for the Solar Orbiter mission will image the solar corona in the extreme ultraviolet (17.1 nm and 30.4 nm) and in the vacuum ultraviolet (121.6 nm) spectral ranges. The development of the EUI instrument has been successfully completed with the optical alignment of its three channels’ telescope, the thermal and mechanical environmental verification, the electrical and software validations, and an end-toend on-ground calibration of the two-units’ flight instrument at the operating wavelengths. The instrument has been delivered and installed on the Solar Orbiter spacecraft, which is now undergoing all preparatory activities before launch.

This paper addresses the computation of radiative exchange factors through Monte Carlo ray tracing with the aim of reducing their computation time when dealing with the finite element method. Both direction and surface samplings are studied. The recently-introduced isocell method for partitioning the unit disk is applied to the direction sampling and compared to other direction sampling methods. It is then combined to different surface sampling schemes with either one or multiple rays traced per surface sampling point. Two promising approaches present better performances than standard spacecraft thermal analysis software. The first approach combines a Gauss surface sampling strategy with a local isocell direction sampling, whereas the second approach fires one ray per surface points using a global isocell direction sampling scheme. The advantages and limitations of the two methods are discussed, and they are benchmarked against a standard thermal analysis software using the entrance baffle of the Extreme Ultraviolet Imager instrument of the Solar Orbiter mission.

The Extreme Ultraviolet Imager (EUI) on-board the Solar Orbiter mission will provide image sequences of the solar atmosphere at selected spectral emission lines in the extreme and vacuum ultraviolet. For the two Extreme Ultraviolet (EUV) channels of the EUI instrument, low noise and radiation tolerant detectors with low power consumption and high sensitivity in the 10-40 nm wavelength range are required to achieve the science objectives. In that frame, a dual-gain 10 μm pixel pitch back-thinned 1k x 1k Active Pixel Sensor (APS) CMOS prototype has been tested during the preliminary development phase of the instrument, to validate the pixel design, the expected EUV sensitivity and noise level, and the capability to withstand the mission radiation environment. Taking heritage of this prototype, the detector architecture has been improved and scaled up to the required 3k x 3k array. The dynamic range is increased, the readout architecture enhanced, the power consumption reduced, and the pixel design adapted to the required stitching. The detector packaging has also been customized to fit within the constraints imposed by the camera mechanical, thermal and electrical boundaries. The manufacturing process has also been adapted and back-thinning process improved. Once manufactured and packaged, a batch of sensors will undergo a characterization and calibration campaign to select the best candidates for integration into the instrument qualification and flight cameras. The flight devices, within their cameras, will then be embarked on the EUI instrument, and be the first scientific APSCMOS detectors for EUV observation of the Sun.

A new solar panel with high concentration photovoltaic technology (x700) has been designed, prototyped and tested in the SOLMACS project. The quality of concentrating optics is a key factor for high module efficiency. Therefore new dedicated PMMA Fresnel lenses were studied and produced by injection molding. Lens design, material and production process were optimized to achieve a high optical yield of 86%. Thorough lens performance assessment in optical laboratory was completed with lifetime UV aging tests. Another important aspect is the thermal control of the hot spot created under the solar cell that receives the concentrated flux of 700 Suns. A dedicated heat spreader was developed to achieve passive thermal control with minimum mass and cost. This was supported by thermal models and tests at both cell and module level. 35% triple junction cells were implemented in the module. Micro-assembly technologies were used for the cell packaging and electrical connections. In support to the research, a continu...