Search

Abstract: An OFA (over-fire air) program and matched measures supporting efficient-combustion are proposed for the FW (Foster Wheeler)-type down-fired boiler, where the OFA is supplied from the arches of the boiler. A gas/solid cold test was conducted at a scale of 1:15, using a two-dimensional laser phase Doppler analyzer to measure parameters in the model furnace, such as the two-phase gas/solid flow velocity, fluctuation velocity, particle size, particle volume flux and particle number concentration. The effects of the OFA ratio on the gas/solid flow characteristics in the furnace were investigated. With an increase in the OFA ratio, the jet depth of the fuel-rich flow decreased. For an OFA ratio of 25%, the jet depth of the fuel-rich flow was much less than that for other OFA ratios, and the residence time of the gas/solid flow in the lower furnace was shorter. An increase in the OFA ratio can increase the penetration depth and allow fuller mixing with the upward airflow, while an OFA ratio that is too great will hinder the upward flow back to the burner nozzle region. An OFA ratio of 20% is considered appropriate for the proposed OFA technical scheme. [Copyright &y& Elsevier]

A new overfire air (OFA) technology was proposed by the authors for a Foster Wheeler down-fired boiler, and a small-scale cold experimental system for a 660-MWe unit was established. The velocity field distribution was measured in the furnace to study the characteristics of single-phase flow in the furnace at different OFA nozzle angles. The furnace temperature and distributions of the O2 concentration and NO concentration at different OFA nozzle angles were simulated using Fluent 6.3.26, and the average temperature of the furnace outlet, the O2 and NO x concentrations and carbon content in the fly ash were calculated. As the OFA nozzle angle increased, the vertical penetration depth of OFA increased and the horizontal penetration depth of OFA gradually decreased. The carbon content in the fly ash and NO x concentration initially rose and then fell at the furnace outlet, and they were lowest when the OFA angle was set at 20°. Thus, according to the findings of this article, an optimized OFA angle of 20° was chosen. [ABSTRACT FROM AUTHOR]

Abstract: We measured various operational parameters of a 200-MWe, wall-fired, lignite utility boiler under different loads. The parameters measured were gas temperature, gas species concentration, char burnout, component release rates (C, H and N), furnace temperature, heat flux, and boiler efficiency. Cold air experiments of a single burner were conducted in the laboratory. A double swirl flow pulverized-coal burner has two ring recirculation zones that start in the secondary air region of the burner. With increasing secondary air flow, the air flow axial velocity increases, the maximum values for the radial velocity, tangential velocity, and turbulence intensity all increase, and there are slight increases in the air flow swirl intensity and the recirculation zone size. With increasing load gas, the temperature and CO concentration in the central region of burner decrease, while O2 concentration, NO x concentration, char burnout, and component release rates of C, H, and N increase. Pulverized-coal ignites farther into the burner, in the secondary air region. Gas temperature, O2 concentration, NO x concentration, char burnout and component release rates of C, H, and N all increase. Furthermore, CO concentration varies slightly and pulverized-coal ignites closer. In the side wall region, gas temperature, O2 concentration, and NO x concentration all increase, but CO concentration varies only slightly. In the bottom row burner region the furnace temperature and heat flux increase appreciably, but the increase become more obvious in the middle and top row burner regions and in the burnout region. Compared with a 120-MWe load, the mean NO x emission at the air preheater exits for 190-MWe load increases from 589.5mg/m3 (O2 =6%) to 794.6mg/m3 (O2 =6%), and the boiler efficiency increases from 90.73% to 92.45%. [Copyright &y& Elsevier]

Abstract: We measured various operational parameters of a 200-MWe, wall-fired, lignite utility boiler under various outer secondary air vane angles. The parameters measured were gas temperature, gas species concentrations, char burnout, and component release rates (C, H and N). Cold air experiments of a single burner were conducted in the laboratory. A double swirl flow pulverized-coal burner has a single ring recirculation zone that forms in the secondary air region in the burner. By decreasing vane angles, maximum values of radial velocity, tangential velocity and turbulence intensity all increase. Moreover, swirl intensity of air flow and recirculation zone size increase. Concomitantly, in the central region of the burner, decreasing the vane angles of outer secondary air increases gas temperatures, CO concentrations, char burnout and component release rates of C, H, and N, while O2 and NO x concentrations decrease, and an early ignition of pulverized-coal occurs. Meanwhile, in the secondary air region of the burner, conditions are similar except that NO x mean concentrations are reversed showing instead an increase. In the side wall region, gas temperatures increase, O2 and NO x concentrations decrease, but CO concentrations vary only slightly. [Copyright &y& Elsevier]

Abstract: Industrial experiments were performed on a down-fired pulverized-coal 300MWe utility boiler with swirl burners. Gas temperature, concentrations of gas components (O2, CO, CO2 and NO x ) in the burning region and carbon content in the fly ash were measured with outer secondary-air vane angles of 25°, 32.5° and 50°. Results indicate that with increasing vane angle, NO x emission and boiler efficiency decrease. Overall evaluation boiler efficiency and NO x emission, the vane angle of 32.5° is optimum. Using an IFA300 constant-temperature anemometer system, cold air experiments on a quarter-scaled burner model were also carried out to investigate the influence of various outer secondary-air vane angles on the flow characteristics in the burner nozzle region. No central recirculation zone appeared for vane angles of 25° and 32.5°. Most of the pulverized-coal was ignited in the external recirculation zone. For vane angles of 45° and 55°, a central recirculation zone could be observed, and air flow rigidity and axial velocities decreased rapidly. [Copyright &y& Elsevier]