Search

Development of MnO 2 based electrode materials for supercapacitor application with high comprehensive electrochemical performance, such as high capacitance, superior reversibility, excellent stability, and good rate capability, is still a tremendous challenge. In this work, a distinctive interwoven three-dimensional (3D) structure electrode with ultra-thin 2D graphene nanosheet decorated on the surface of 1D C/TiC nanowire array is built as the support to immobilize MnO 2 nanoflakes (MnO 2 -Graphene nanosheet-C/TiC nanowire array, denoted as MGCT). Compared with the normal 1D core/shell structure, this novel 3D architecture can dramatically not only increase the surface area for MnO 2 loading but also facilitate the ion and electron transfer. The electrochemical performance of the as-prepared 3D MnO 2 electrode is evaluated by cyclic voltammetrys, galvanostatic charging-discharging tests and electrochemical impedance spectroscopy, high specific capacitance (856 F g −1 at 2 A g −1 ), good rate capability (69.1% capacitance retention at 40 A g −1 vs 2 A g −1 ), superior reversibility, and cycling stability (85.7% capacitance retention after 10,000 cycles at 10 A g −1 ) are obtained, suggesting that this novel structure can offer a new and appropriate idea for obtaining high-performance supercapacitor electrode materials. [ABSTRACT FROM AUTHOR]

Nanoporous palladium supported on the carbon coated titanium carbide (C@TiC) nanowire arrays (Pd NP/C@TiC) are successfully prepared by a facile chemical vapor deposition of three-dimensional (3D) C@TiC substrate, followed by electrochemical codeposition of Pd–Ni and removal of Ni via dealloying. The structure and morphology of the obtained Pd NP/C@TiC electrodes are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), field-emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). Cyclic voltammetry (CV), linear sweep voltammetry (LSV), chronoamperometry (CA) and electrochemical impedance spectroscopy (EIS) are used to examine the catalytic performances of the electrodes for H 2 O 2 electroreduction in H 2 SO 4 solution. The Pd NP/C@TiC electrode exhibits a largely effective specific surface area owing to its open nanoporous structure allowing the full utilization of Pd surface active sites. At the potential of 0.2 V in 2.0 mol L −1 H 2 O 2 and 2 mol L −1 H 2 SO 4 solutions, the reduction current density reaches 3.47 A mg −1 , which is significantly higher than the catalytic activity of H 2 O 2 electroreduction achieved previously with precious metals as catalysts. [ABSTRACT FROM AUTHOR]

A novel three-dimensional carbon- and binder-free nickel nanowire arrays (Ni NAs) electrode is successfully fabricated by a facile galvanostatic electrodeposition method using polycarbonate membrane as the template. The Ni NAs electrode achieves a oxidation current density (divided by the electroactive surface areas of Ni) of 25.1 mA cm −2 in 4 mol L −1 KOH and 0.9 mol L −1 H 2 O 2 at 0.2 V (vs. Ag/AgCl) accompanied with a desirable stability, which is significantly higher than the catalytic activity of H 2 O 2 electro-oxidation achieved previously with precious metals as catalysts. The impressive electrocatalytic performance is largely attributed to the superior 3D open structure and high electronic conductivity, which ensures the high utilization of Ni surfaces and makes the electrode have higher electrochemical activity. The apparent activation energy of H 2 O 2 electro-oxidation on the Ni NAs catalyst is 13.59 kJ mol −1 . A direct peroxide–peroxide fuel cell using the Ni NAs as anode exhibits a peak power density of 48.7 mW cm −2 at 20 °C. The electrode displays a great promise as the anode of direct peroxide–peroxide fuel cell due to its low cost, high activity and stability. [ABSTRACT FROM AUTHOR]

Binary metal niobium oxides can offer a higher specific capacity compared to niobium pentoxide (Nb 2 O 5) and thus are ideal anode candidates for lithium ion capacitors (LICs). However, their lower electronic conductivity limits their ability to achieve high energy and power densities. In this paper, one-dimensional (1D) copper niobate (CuNb 2 O 6) nanowires are successfully prepared by electrospinning technology and then immobilized on two-dimensional (2D) reduced graphene oxide (rGO) nanosheets to form a unique 1D nanowire/2D nanosheet CuNb 2 O 6 /rGO structure. The 1D/2D CuNb 2 O 6 /rGO electrode exhibits a high specific capacity of 312.2 mAh g−1 at 100 mA g−1 as the anode of LICs. The proposed Li+ storage mechanism of the CuNb 2 O 6 anode involves CuNb 2 O 6 decomposition into lithium niobate (Li 3 NbO 4) and copper (Cu) during the initial lithium insertion process. The intercalation-type Li 3 NbO 4 will further serve as the host to Li+ and the inactive Cu phase will act as a conductive network for electron transportation. Furthermore, the energy density of the assembled CuNb 2 O 6 /rGO//activated carbon (CuNb 2 O 6 /rGO//AC) device could achieve a value as high as 92.1 Wh kg−1 and could thus be considered as a possible alternative electrode material for high energy and power LICs. [ABSTRACT FROM AUTHOR]

Urea peroxide as a solid-state fuel instead of liquid hydrogen peroxide is electro-catalytic oxidized by nickel nanowire arrays (NWAs) electrode. Nickel NWAs electrode is prepared by galvanostatically electrodepositing nickel into the pores and over-plating on the surface of polycarbonate template (PCT) from nickel bath solution. The NWAs are obtained after dissolving PCT in methylene chloride. Results show that urea peroxide decomposes into hydrogen peroxide and urea in aqueous solutions, then is electro-oxidized via two processes: i, hydrogen peroxide electro-oxidation at lower potential region; ii, both hydrogen peroxide and urea electro-oxidation at higher potential region. The onset oxidation potential and current density of urea peroxide electro-oxidation in 6.0 mol L −1 KOH and 1.0 mol L −1 urea peroxide are ca. -0.2 V and 700 mA cm −2 at 0.6 V, respectively. The nickel NWAs electrode demonstrates excellent stability for urea peroxide electro-oxidation under different polarization potentials. [ABSTRACT FROM AUTHOR]

Abstract: Nanowire arrays of mixed oxides of Co and Ni freely standing on Ni foam are prepared by a template-free growth method. The effects of Ni content on the morphology, structure and catalyst performance for oxygen evolution reaction are investigated by scanning electron microscopy, X-ray diffraction spectroscopy and electrochemical techniques including cyclic voltammetry, chronopotentiometry and electrochemical impedance spectroscopy. A transformation from nanowire arrays to nanoplate arrays is found with the increase of the atomic ratio of Ni to Co in the preparation solution. The NixCo3−xO4 electrode obtained at 1:1 of Ni:Co in the preparation solution exhibits nanowire array structure and has better catalytic performance for oxygen evolution reaction than other NixCo3−xO4 and Co3O4 electrodes. The catalytic activities of the NixCo3−xO4 and Co3O4 electrodes are correlated with their surface roughness. Superior stability of the NixCo3−xO4 nanowire array electrode is demonstrated by a chronopotentiometric test. The reaction orders with respect to OH− on the NixCo3−xO4 electrode are close to 2 and 1 at low and high overpotentials, respectively. [Copyright &y& Elsevier]