Search

Wafer scale (cm(2)) arrays and networks of nanochannels were created in polydimethylsiloxane (PDMS) from a surface pattern of electrodeposited gold nanowires in a master-replica process and characterized with scanning electron microscopy (SEM), atomic force microscopy (AFM), and fluorescence imaging measurements. Patterns of gold nanowires with cross-sectional dimensions as small as 50 nm in height and 100 nm in width were prepared on silica substrates using the process of lithographically patterned nanowire electrodeposition (LPNE). These nanowire patterns were then employed as masters for the fabrication of inverse replica nanochannels in a special formulation of PDMS. SEM and AFM measurements verified a linear correlation between the widths and heights of the nanowires and nanochannels over a range of 50 to 500 nm. The PDMS replica was then oxygen plasma-bonded to a glass substrate in order to create a linear array of nanofluidic channels (up to 1 mm in length) filled with solutions of either fluorescent dye or 20 nm diameter fluorescent polymer nanoparticles. Nanochannel continuity and a 99% fill success rate was determined from the fluorescence imaging measurements, and the electrophoretic injection of both dye and nanoparticles in the nanochannel arrays was also demonstrated. Employing a double LPNE fabrication method, this master-replica process was also used to create a large two-dimensional network of crossed nanofluidic channels.

The properties of a single heated palladium (Pd) nanowire for the detection of hydrogen gas (H(2)) are explored. In these experiments, a Pd nanowire, 48-98 microm in length, performs three functions in parallel: 1) Joule self-heating is used to elevate the nanowire temperature by up to 128 K, 2) the 4-contact wire resistance in the absence of H(2) is used to measure its temperature, and 3) the nanowire resistance in the presence of H(2) is correlated with its concentration, allowing it to function as a H(2) sensor. Compared with the room-temperature response of a Pd nanowire, the response of the heated nanowire to hydrogen is altered in two ways: First, the resistance change (DeltaR/R(0)) induced by H(2) exposure at any concentration is reduced by a factor of up to 30 and second, the rate of the resistance change - observed at the beginning ("response") and at the end ("recovery") of a pulse of H(2) - is increased by more than a factor of 50 at some H(2) concentrations. Heating nearly eliminates the retardation of response and recovery seen from 1-2% H(2), caused by the alpha --> beta phase transition of PdH(x), a pronounced effect for nanowires at room temperature. The activation energies associated with sensor response and recovery are measured and interpreted.

Lithographically patterned nanowire electrodeposition (LPNE) provides a method for patterning nanowires composed of nanocrystalline cadmium selenide (nc-CdSe) over wafer-scale areas. We assess the properties of (nc-CdSe) nanowires for detecting light as photoconductors. Structural characterization of these nanowires by X-ray diffraction and transmission electron microscopy reveals they are composed of stoichiometric, single phase, cubic CdSe with a mean grain diameter of 10 nm. For nc-CdSe nanowires with lengths of many millimeters, the width and height dimensions could be varied over the range from 60 to 350 nm (w) and 20 to 80 nm (h). Optical absorption and photoluminescence spectra for nc-CdSe nanowires were both dominated by band-edge transitions. The photoconductivity properties of nc-CdSe nanowire arrays containing approximately 350 nanowires were evaluated by electrically isolating 5 microm nanowire lengths using evaporated gold electrodes. Photocurrents, i(photo), of 10-100 x (i(dark)) were observed with a spectral response characterized by an onset at 1.75 eV. i(photo) response and recovery times were virtually identical and in the range from 20 to 40 micros for 60 x 200 nm nanowires.

Nanowires of lead telluride (PbTe) were patterned on glass surfaces using lithographically patterned nanowire electrodeposition (LPNE). LPNE involved the fabrication by photolithography of a contoured nickel nanoband that is recessed by approximately 300 nm into a horizontal photoresist trench. Cubic PbTe was then electrodeposited from a basic aqueous solution containing Pb(2+) and TeO(3)(2-) at the nickel nanoband using a cyclic deposition/stripping potential program in which lead-rich PbTe was first deposited in a negative-going potential scan and excess lead was then anodically stripped from the nascent nanowire by scanning in the positive direction to produce near stoichiometric PbTe. Repeating this scanning procedure permitted PbTe nanowires 60-400 nm in width to be obtained. The wire height was controlled over the range of 20-100 nm based upon the nickel film thickness. Nanowires with lengths exceeding 1 cm were prepared in this study. We report the characterization of these nanowires using X-ray diffraction, transmission electron microscopy and electron diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy (XPS). The surface chemical composition of PbTe nanowires was monitored by XPS as a function of time during the exposure of these nanowires to laboratory air. One to two monolayers of a mixed Pb and Te oxide are formed during a 24 h exposure. The electrical conductivity of PbTe nanowires was strongly affected by air oxidation, declining from an initial value of 2.0(+/-1.5) x 10 (4) S/m by 61% (for nanowires with a 20 nm thickness), 55% (for 40 nm), and 12% (for 60 nm).

Lithographically patterned nanowire electrodeposition (LPNE) is a new method for fabricating polycrystalline metal nanowires using electrodeposition. In LPNE, a sacrificial metal (M(1)=silver or nickel) layer, 5-100 nm in thickness, is first vapor deposited onto a glass, oxidized silicon, or Kapton polymer film. A (+) photoresist (PR) layer is then deposited, photopatterned, and the exposed Ag or Ni is removed by wet etching. The etching duration is adjusted to produce an undercut approximately 300 nm in width at the edges of the exposed PR. This undercut produces a horizontal trench with a precisely defined height equal to the thickness of the M(1) layer. Within this trench, a nanowire of metal M(2) is electrodeposited (M(2)=gold, platinum, palladium, or bismuth). Finally the PR layer and M(1) layer are removed. The nanowire height and width can be independently controlled down to minimum dimensions of 5 nm (h) and 11 nm (w), for example, in the case of platinum. These nanowires can be 1 cm in total length. We measure the temperature-dependent resistance of 100 microm sections of Au and Pd wires in order to estimate an electrical grain size for comparison with measurements by X-ray diffraction and transmission electron microscopy. Nanowire arrays can be postpatterned to produce two-dimensional arrays of nanorods. Nanowire patterns can also be overlaid one on top of another by repeating the LPNE process twice in succession to produce, for example, arrays of low-impedance, nanowire-nanowire junctions.

Electrochemistry intersected nanoscience 25 years ago when it became possible to control the flow of electrons through single molecules and nanostructures. Many surprises and a wealth of understanding were generated by these experiments. Professor Nongjian Tao was among the pioneering scientists who created the methods and technologies for advancing this new frontier. Achieving a deeper understanding of charge transport in molecules and low-dimensional materials was the first priority of his experiments, but he also succeeded in discovering applications in chemical sensing and biosensing for these novel nanoscopic systems. In parallel with this work, the investigation of a range of phenomena using novel optical microscopic methods was a passion of his and his students. This article is a review and an appreciation of some of his many contributions with a view to the future.

The design and use of materials in the nanoscale size range for addressing medical and health-related issues continues to receive increasing interest. Research in nanomedicine spans a multitude of areas, including drug delivery, vaccine development, antibacterial, diagnosis and imaging tools, wearable devices, implants, high-throughput screening platforms, etc. using biological, nonbiological, biomimetic, or hybrid materials. Many of these developments are starting to be translated into viable clinical products. Here, we provide an overview of recent developments in nanomedicine and highlight the current challenges and upcoming opportunities for the field and translation to the clinic.

Nanoscience and nanotechnology are poised to contribute to a wide range of fields, from health and medicine to electronics, energy, security, and more. These contributions come both directly in the form of new materials, interfaces, tools, and even properties as well as indirectly by connecting fields together. We celebrate how far we have come, and here, we look at what is to come over the next decade that will leverage the strong and growing base that we have built in nanoscience and nanotechnology.

We demonstrate the de novo fabrication of a biosensor, based upon virus-containing poly(3,4-ethylene-dioxythiophene) (PEDOT) nanowires, that detects prostate-specific membrane antigen (PSMA). This development process occurs in three phases: (1) isolation of a M13 virus with a displayed polypeptide receptor, from a library of ≈1011 phage-displayed peptides, which binds PSMA with high affinity and selectivity, (2) microfabrication of PEDOT nanowires that entrain these virus particles using the lithographically patterned nanowire electrodeposition (LPNE) method, and (3) electrical detection of the PSMA in high ionic strength (150 mM salt) media, including synthetic urine, using an array of virus-PEDOT nanowires with the electrical resistance of these nanowires for transduction. The electrical resistance of an array of these nanowires increases linearly with the PSMA concentration from 20 to 120 nM in high ionic strength phosphate-buffered fluoride (PBF) buffer, yielding a limit of detection (LOD) for PSMA of 56 nM. [ABSTRACT FROM AUTHOR]

Surface patterns of single-stranded DNA (ssDNA) consisting of nanoscale lines as thin as 40 nan were fabricated on polymer substrates for nanotechnology and bioaffinity sensing applications. Iarge scale arrays (with areas up to 4 cm2) of ssDNA "nanolines" were created on streptavidin-coated polymer (PDMS) surfaces by transferring biotinylated ssDNA from a master pattern of gold nanowires attached to a glass substrate. The gold nanowires were first formed on the glass substrate by the process of lithographically patterned nanowire electrodeposition (LPNE), and then "inked" with biotinylated ssDNA by hybridization adsorption to a thiolmodified ssDNA monolayer attached to the gold nanowires. The transferred ssDNA nanolines were capable of hybridizing with ssDNA from solution to form double-stranded DNA (dsDNA) patterns; a combination of fluorescence and atomic force microscopy (AFM) measurements were used to characterize the dsDNA nanoline arrays. To demonstrate the utility of these surices for biosensing, optical diffraction measurements of the hybridization adsorption of DNA-coated gold nanoparticles onto the ssDNA nanoline arrays were used to detect a specific target sequence of unlabeled ssDNA in solution. [ABSTRACT FROM AUTHOR]