Search

Background and Purpose: Thermochromic gel phantoms provide a controlled medium for visual assessment of thermal ablation device performance. However, there are limited studies reporting on the comparative assessment of ablation profiles assessed in thermochromic gel phantoms against those in ex vivo tissue. The objective of this study was to compare microwave ablation zones in a thermochromic tissue-mimicking gel phantom and ex vivo bovine liver and to report on measurements of the temperature-dependent dielectric and thermal properties of the phantom., Methods: Thermochromic polyacrylamide phantoms were fabricated following a previously reported protocol. Phantom samples were heated to temperatures in the range of 20°C-90°C in a temperature-controlled water bath, and colorimetric analysis of images of the phantom taken after heating was used to develop a calibration between color changes and the temperature to which the phantom was heated. Using a custom, 2.45 GHz water-cooled microwave ablation antenna, ablations were performed in fresh ex vivo liver and phantoms using 65 W applied for 5 min or 10 min (n = 3 samples in each medium for each power/time combination). Broadband (500 MHz-6 GHz) temperature-dependent dielectric and thermal properties of the phantom were measured over the temperature range of 22°C-100°C., Results: Colorimetric analysis showed that the sharp change in gel phantom color commences at a temperature of 57°C. Short and long axes of the ablation zone in the phantom (as assessed by the 57°C isotherm) for 65 W, 5 min ablations were aligned with the extents of the ablation zone observed in ex vivo bovine liver. However, for the 65 W, 10 min setting, ablations in the phantom were on average 23.7% smaller in the short axis and 7.4 % smaller in the long axis than those observed in ex vivo liver. Measurements of the temperature-dependent relative permittivity, thermal conductivity, and volumetric heat capacity of the phantom largely followed similar trends to published values for ex vivo liver tissue., Conclusion: Thermochromic tissue-mimicking phantoms provides a controlled, and reproducible medium for comparative assessment of microwave ablation devices and energy delivery settings. However, ablation zone size and shapes in the thermochromic phantom do not accurately represent ablation sizes and shapes observed in ex vivo liver tissue for high energy delivery treatments (65 W, 10 min). One cause for this limitation is the difference in temperature-dependent thermal and dielectric properties of the thermochromic phantom compared to ex vivo bovine liver tissue, as reported in the present study., (© 2024 American Association of Physicists in Medicine.)

Purpose: To develop a computational model of microwave ablation (MWA) with a thermal accelerant gel and apply the model toward interpreting experimental observations in ex vivo bovine and in vivo porcine liver., Methods: A 3D coupled electromagnetic-heat transfer model was implemented to characterize thermal profiles within ex vivo bovine and in vivo porcine liver tissue during MWA with the HeatSYNC thermal accelerant. Measured temperature dependent dielectric and thermal properties of the HeatSYNC gel were applied within the model. Simulated extents of MWA zones and transient temperature profiles were compared against experimental measurements in ex vivo bovine liver. Model predictions of thermal profiles under in vivo conditions in porcine liver were used to analyze thermal ablations observed in prior experiments in porcine liver in vivo ., Results: Measured electrical conductivity of the HeatSYNC gel was ∼83% higher compared to liver at room temperature, with positive linear temperature dependency, indicating increased microwave absorption within HeatSYNC gel compared to tissue. In ex vivo bovine liver, model predicted ablation zone extents of (31.5 × 36) mm with the HeatSYNC, compared to (32.9 ± 2.6 × 40.2 ± 2.3) mm in experiments (volume differences 4 ± 4.1 cm 3 ). Computational models under in vivo conditions in porcine liver suggest approximating the HeatSYNC gel spreading within liver tissue during ablations as a plausible explanation for larger ablation zones observed in prior in vivo studies., Conclusion: Computational models of MWA with thermal accelerants provide insight into the impact of accelerant on MWA, and with further development, could predict ablations with a variety of gel injection sites.

Microwave ablation is under investigation as a minimally-invasive treatment for uterine fibroids. Computational models play a vital role in the development, evaluation and characterization of candidate ablation devices. The temperature-dependent dielectric properties of fibroid tissue are essential for accurate computational modeling. Objective: To measure the broadband temperature-dependent dielectric properties of uterine fibroids excised during hysterectomy procedures. Methods : The open-ended coaxial probe method was employed for measuring the broadband dielectric properties of freshly excised human uterine fibroid samples (n = 6) obtained from an IRB-approved tissue bank. The dielectric properties (relative permittivity, ε r , and effective electrical conductivity, σ eff ) were evaluated at temperatures ranging from 23 °C-150 °C, over the frequency range of 0.5-6 GHz. Linear piecewise parametrization with respect to temperature and quadratic parametrization with respect to frequency was applied to characterize broadband temperature-dependent dielectric properties of fibroid tissue. Results : The baseline room temperature values of ε r vary from 57.5 ± 5.29 to 44.5 ± 5.77 units and σ eff changes from 0.91 ± 0.19 to 6.02 ± 0.7 S m -1 over the frequency range of 0.5-6 GHz. At temperatures close to the water vaporization point, ε r , drops considerably i.e. to 12%-14% of its baseline value for all measured frequencies. σ eff values initially rise till 98 °C and then fall to 11%-13% of their baseline values at 125 °C for frequencies ≤2.45 GHz. The σ eff follows a decreasing trend for frequencies >2.45 GHz and drops to ∼6 % of their baseline room temperature values. Conclusion: The temperature dependent dielectric properties of uterine fibroid tissues over microwave frequency range are reported for the first time in this study. Parametric models of uterine fibroid dielectric properties are also presented for incorporation within computational models of microwave ablation of fibroids., (© 2021 IOP Publishing Ltd.)

Type 2 uterine fibroids are challenging to resect surgically as ≥ 50% volume of myoma lies within the myometrium. A hysteroscopic approach for ablating fibroids is minimally-invasive, but places a considerable burden on the operator to accurately place the ablation applicator within the target. We investigated the sensitivity of transcervical microwave ablation outcome with respect to position of the ablation applicator within 1 - 3 cm type 2 fibroids. Methods: A finite element computer model was developed to simulate 5.8 GHz microwave ablation of fibroids and validated with experiments in ex vivo tissue. The ablation outcome was evaluated with respect to applicator insertion angles (30°, 45°, 60°) , depth and offset from the fibroid center (±2 mm for 3 cm fibroid and ±1 mm for 1 cm fibroid) with 35 W and 15 W applied power for 3 cm and 1 cm fibroids, respectively. Power deposition was stopped when thermal dose of 40 cumulative equivalent minutes at 43 °C (CEM43) was accrued in adjacent myometrium. Results: Within the range of all evaluated insertion angles, depths and offsets, the ablation coverage was less sensitive to variation in angle as compared to depth and offset, and ranged from 34.9 - 83.6% for 3 cm fibroid in 140 - 400 s and 34.1 - 67.9% for 1 cm fibroid in 30 - 50 s of heating duration. Maximum achievable ablation coverage in both fibroid cases reach ∼ 90% if thermal dose is allowed to exceed 40 CEM43 in myometrium. Conclusion: The study demonstrates the technical feasibility of transcervical microwave ablation for fibroid treatment and the relationship between applicator position within the fibroid and fraction of fibroid that can be ablated while limiting thermal dose in adjacent myometrium., (© 2021 IOP Publishing Ltd.)

Objective: To investigate the thermal and frequency dependence of dielectric properties of ex vivo liver tissue - relative permittivity and effective conductivity - over the frequency range 500 MHz to 6 GHz and temperatures ranging from 20 to 130 °C., Methods: We measured the dielectric properties of fresh ex vivo bovine liver tissue using the open-ended coaxial probe method (n = 15 samples). Numerical optimization techniques were utilized to obtain parametric models for characterizing changes in broadband dielectric properties as a function of temperature and thermal isoeffective dose. The effect of heating tissue at rates over the range 6.4-16.9 °C/min was studied. The measured dielectric properties were used in simulations of microwave ablation to assess changes in simulated antenna return loss compared to experimental measurements., Results: Across all frequencies, both relative permittivity and effective conductivity dropped sharply over the temperature range 89 - 107 °C. Below 91 °C, the slope of the effective conductivity changes from positive values at lower frequencies (0.5-1.64 GHz) to negative values at higher frequencies (1.64-6 GHz). The maximum achieved correlation values between transient reflection coefficients from measurements and simulations ranged between 0.83 - 0.89 and 0.68 - 0.91, respectively, when using temperature-dependent and thermal-dose dependent dielectric property parameterizations., Conclusion: We have presented experimental measurements and parametric models for characterizing changes in dielectric properties of bovine liver tissue at ablative temperatures., Significance: The presented dielectric property models will contribute to the development of ablation systems operating at frequencies other than 2.45 GHz, as well as broadband techniques for monitoring growth of microwave ablation zones.

Purpose: To experimentally characterize a microwave (MW) ablation applicator designed to produce directional ablation zones., Materials and Methods: Using a 14-gauge, 2.45-GHz side-firing MW ablation applicator, 36 ex vivo bovine liver ablations were performed. Ablations were performed at 60 W, 80 W, and 100 W for 3, 5, and 10 minutes (n = 4 per combination). Ablation zone forward and backward depth and width were measured and directivity was calculated as the ratio of forward to backward depth. Thirteen in vivo ablations were performed in 2 domestic swine with the applicator either inserted into the liver (80 W, 5 min, n = 3; 100 W, 5 min, n = 3; 100 W, 10 min, n = 2) or placed on the surface of the liver with a nontarget tissue placed on the back side of the applicator (80 W, 5 min, n = 5). The animals were immediately euthanized after the procedure; the livers were harvested and sectioned perpendicular to the axis of the applicator. In vivo ablation zones were measured following viability staining and assessed on histopathology., Results: Mean ex vivo ablation forward depth was 8.3-15.5 mm. No backward heating was observed at 60 W, 3-5 minutes; directivity was 4.7-11.0 for the other power and time combinations. In vivo ablation forward depth was 10.3-11.5 mm, and directivity was 11.5-16.1. No visible or microscopic thermal damage to nontarget tissues in direct contact with the back side of the applicator was observed., Conclusions: The side-firing MW ablation applicator can create directional ablation zones in ex vivo and in vivo tissues., (Copyright © 2020 SIR. Published by Elsevier Inc. All rights reserved.)

Purpose: The objective of this study is to develop a computational model for simulating 915 MHz microwave ablation (MWA), and verify the simulation predictions of transient temperature profiles against experimental measurements. Due to the limited experimental data characterizing temperature-dependent changes of tissue dielectric properties at 915 MHz, we comparatively assess two temperature-dependent approaches of modeling of dielectric properties: model A- piecewise linear temperature dependencies based on existing, but limited, experimental data, and model B- similar to model A, but augmented with linear decrease in electrical conductivity above 95 °C, as guided by our experimental measurements., Methods: The finite element method was used to simulate MWA procedures in liver with a clinical 915 MHz ablation applicator. A coupled electromagnetic-thermal solver incorporating temperature-dependent tissue biophysical properties of liver was implemented. Predictions of the transient temperature profiles and ablation zone dimensions for both model A and model B were compared against experimental measurements in ex vivo bovine liver tissue. Broadband dielectric properties of tissue within different regions of the ablation zone were measured and reported at 915 MHz and 2.45 GHz., Results: Model B yielded peak tissue temperatures in closer agreement with experimental measurements, attributed to the inclusion of decrease in electrical conductivity at elevated temperature. The simulated transverse diameters of the ablation zone predicted by both models were greater than experimental measurements, which may be in part due to the lack of a tissue shrinkage model. At both considered power levels, predictions of transverse ablation zone diameters were in closer agreement with measurements for model B (max. discrepancy of 5 mm at 60 W, and 3 mm at 30 W), compared to model A (max. discrepancy of 9 mm at 60 W, and 6 mm at 30 W). Ablation zone lengths with both models were within 2 mm at 30 W, but overestimated by up to 10 mm at 60 W., Conclusions: The inclusion of decreased electrical conductivity above 95 °C, implemented with model B as guided by our experimental measurements, may be a good approach for approximating the dynamic changes that occur during MWA at 915 MHz. Although a step toward more effectively modeling MWA at 915 MHz, further investigation of the transition in dielectric properties with temperature and tissue shrinkage, especially at high temperatures is needed for more accurate simulations., (© 2017 American Association of Physicists in Medicine.)

Purpose: Microwave ablation (MWA) applicators capable of creating directional heating patterns offer the potential of simplifying treatment of targets in proximity to critical structures and avoiding the need for piercing the tumour volume. This work reports on improved directional MWA antennas with the objectives of minimising device diameter for percutaneous use (≤ ∼13 gauge) and yielding larger ablation zones., Methods: Two directional MWA antenna designs, with a modified monopole radiating element and spherical and parabolic reflectors are proposed. A 3D-coupled electromagnetic heat transfer with temperature-dependent material properties was implemented to characterise MWA at 40 and 77 W, for 5 and 10 min. Simulations were also used to assess antenna impedance matching within liver, kidney, lung, bone and brain tissue. The two antenna designs were fabricated and experimentally evaluated with ablations in ex vivo tissue at the two power levels and treatment durations (n = 5 repetitions for each group)., Results: The computed specific absorption rate (SAR) patterns for both antennas were similar, although simulations indicated slightly greater forward penetration for the parabolic antenna. Based on simulations for antennas inserted within different tissues, the proposed antenna design appears to offer good impedance matching for a variety of tissue types. Experiments in ex vivo tissue showed radial ablation depths of 19 ± 0.9 mm in the forward direction for the applicator with spherical reflector and 18.7 ± 0.7 mm for the applicator with parabolic reflector., Conclusion: These results suggest the applicator may be suitable for creating localised directional ablation zones for treating small and medium-sized targets with a percutaneous approach.

Purpose: Computational models of microwave ablation (MWA) are widely used during the design optimization of novel devices and are under consideration for patient-specific treatment planning. The objective of this study was to assess the sensitivity of computational models of MWA to tissue biophysical properties., Methods: The Morris method was employed to assess the global sensitivity of the coupled electromagnetic-thermal model, which was implemented with the finite element method (FEM). The FEM model incorporated temperature dependencies of tissue physical properties. The variability of the model was studied using six different outputs to characterize the size and shape of the ablation zone, as well as impedance matching of the ablation antenna. Furthermore, the sensitivity results were statistically analyzed and absolute influence of each input parameter was quantified. A framework for systematically incorporating model uncertainties for treatment planning was suggested., Results: A total of 1221 simulations, incorporating 111 randomly sampled starting points, were performed. Tissue dielectric parameters, specifically relative permittivity, effective conductivity, and the threshold temperature at which they transitioned to lower values (i.e., signifying desiccation), were identified as the most influential parameters for the shape of the ablation zone and antenna impedance matching. Of the thermal parameters considered in this study, the nominal blood perfusion rate and the temperature interval across which the tissue changes phase were identified as the most influential. The latent heat of tissue water vaporization and the volumetric heat capacity of the vaporized tissue were recognized as the least influential parameters. Based on the evaluation of absolute changes, the most important parameter (perfusion) had approximately 40.23 times greater influence on ablation area than the least important parameter (volumetric heat capacity of vaporized tissue). Another significant input parameter (permittivity) had 22.26 times higher influence on the deviation of ablation edge shape from a sphere than one of the less important parameters (latent heat of liver tissue vaporization)., Conclusions: Dielectric parameters, blood perfusion rate, and the temperature interval across which the tissue changes phase were found to have the most significant impact on MWA model outputs. The latent heat of tissue water vaporization and the volumetric heat capacity of the vaporized tissue were recognized as the least influential parameters. Uncertainties in model outputs identified in this study can be incorporated to provide probabilistic maps of expected ablation outcome for patient-specific treatment planning.

Purpose: Bio-effects following thermal treatments are a function of the achieved temperature profile in tissue, which can be estimated across tumor volumes with real-time MRI thermometry (MRIT). Here, we report on expansion of a previously developed small-animal microwave hyperthermia system integrated with MRIT for delivering thermal ablation to subcutaneously implanted tumors in mice. Methods: Computational models were employed to assess suitability of the 2.45 GHz microwave applicators for delivering ablation to subcutaneous tumor targets in mice. Phantoms and ex-vivo tissues were heated to temperatures in the range 47–67 °C with custom-made microwave applicators for validating MRIT with the proton resonance frequency shift method against fiberoptic thermometry. HAC15 tumors implanted in nude mice (n = 6) were ablated in vivo and monitored with MRIT in multiple planes. One day post ablation, animals were euthanized, and excised tumors were processed for viability assessment. Results: Average absolute error between temperatures from fiberoptic sensors and MRIT was 0.6 °C across all ex-vivo ablations. During in-vivo experiments, tumors with volumes ranging between 5.4–35.9 mm³ (mean 14.2 mm³) were ablated (duration: 103–150 s) to achieve 55 °C at the tumor boundary. Thermal doses ≥240 CEM43 were achieved across 90.7–98.0% of tumor volumes for four cases. Ablations were incomplete for remaining cases, attributed to motion-affected thermometry. Thermal dose-based ablative tumor coverage agreed with viability assessment of excised tumors. Conclusions: We have developed a system for delivering microwave ablation to subcutaneous tumors in small animals under MRIT guidance and demonstrated its performance in-vivo. [ABSTRACT FROM AUTHOR]

Purpose: To assess the feasibility of delivering microwave ablation for targeted treatment of aldosterone producing adenomas using image-based computational models. Methods: We curated an anonymized dataset of diagnostic 11C-metomidate PET/CT images of 14 patients with aldosterone producing adenomas (APA). A semi-automated approach was developed to segment the APA, adrenal gland, and adjacent organs within 2 cm of the APA boundary. The segmented volumes were used to implement patient-specific 3D electromagnetic-bioheat transfer models of microwave ablation with a 2.45 GHz directional microwave ablation applicator. Ablation profiles were quantitatively assessed based on the extent of the APA target encompassed by an ablative thermal dose, while limiting thermal damage to the adjacent normal adrenal tissue and sensitive critical structures. Results: Across the 14 patients, adrenal tumor volumes ranged between 393 mm3 and 2,395 mm3 . On average, 70% of the adrenal tumor volumes received an ablative thermal dose of 240CEM43, while limiting thermal damage to non-target structures, and thermally sparing 83.5–96.4% of normal adrenal gland. Average ablation duration was 293 s (range: 60–600 s). Simulations indicated coverage of the APA with an ablative dose was limited when the axis of the ablation applicator was not well aligned with the major axis of the targeted APA. Conclusions: Image-based computational models demonstrate the potential for delivering microwave ablation to APA targets within the adrenal gland, while limiting thermal damage to surrounding nontarget structures. [ABSTRACT FROM AUTHOR]

Purpose: Microwave ablation (MWA) is a clinically established modality for treatment of lung tumors. A challenge with existing application of MWA, however, is local tumor progression, potentially due to failure to establish an adequate treatment margin. This study presents a robust simulation‐based treatment planning methodology to assist operators in comparatively assessing thermal profiles and likelihood of achieving a specified minimum margin as a function of candidate applied energy parameters. Methods: We employed a biophysical simulation‐based probabilistic treatment planning methodology to evaluate the likelihood of achieving a specified minimum margin for candidate treatment parameters (i.e., applied power and ablation duration for a given applicator position within a tumor). A set of simulations with varying tissue properties was evaluated for each considered combination of power and ablation duration, and for four different scenarios of contrast in tissue biophysical properties between tumor and normal lung. A treatment planning graph was then assembled, where distributions of achieved minimum ablation zone margins and collateral damage volumes can be assessed for candidate applied power and treatment duration combinations. For each chosen power and time combination, the operator can also visualize the histogram of ablation zone boundaries overlaid on the tumor and target volumes. We assembled treatment planning graphs for generic 1, 2, and 2.5 cm diameter spherically shaped tumors and also illustrated the impact of tissue heterogeneity on delivered treatment plans and resulting ablation histograms. Finally, we illustrated the treatment planning methodology on two example patient‐specific cases of tumors with irregular shapes. Results: The assembled treatment planning graphs indicate that 30 W, 6 min ablations achieve a 5‐mm minimum margin across all simulated cases for 1‐cm diameter spherical tumors, and 70 W, 10 min ablations achieve a 3‐mm minimum margin across 90% of simulations for a 2.5‐cm diameter spherical tumor. Different scenarios of tissue heterogeneity between tumor and lung tissue revealed 2 min overall difference in ablation duration, in order to reliably achieve a 4‐mm minimum margin or larger each time for 2‐cm diameter spherical tumor. Conclusions: An approach for simulation‐based treatment planning for microwave ablation of lung tumors is illustrated to account for the impact of specific geometry of the treatment site, tissue property uncertainty, and heterogeneity between the tumor and normal lung. [ABSTRACT FROM AUTHOR]