Search

This paper presents measurements using a dual-polarised radiometer operating at 93 GHz to detect ice or water on asphalt in laboratory conditions. The brightness temperatures of both H and V polarizations were measured for a dry surface, liquid water, and ice on asphalt at observation angles of 50° and 56°. The results presented in this paper demonstrate that the studied road conditions can be identified by the radiometer. The measurements are compared with a model and surface parameters, such as dielectric constant and roughness are fitted and compared to reference values. The experiments and results, described in this article, are the first steps towards the future installation of a polarimetric sensor on a moving vehicle for traffic safety. [ABSTRACT FROM AUTHOR]

The Temporal Experiment for Storms and Tropical Systems Technology Demonstration (TEMPEST-D) instrument is a five-frequency millimeter-wave radiometer operating from 87 to 181 GHz. The cross-track scanning radiometer has been operating on a 6U CubeSat in low Earth orbit since September 5, 2018. The direct-detection architecture of the radiometer reduces its mass and power consumption by eliminating the need for a local oscillator and mixer, also reducing system complexity. The instrument includes a scanning reflector and ambient calibration target. The reflector rotates continuously to scan the antenna beams in the cross-track direction, first across the blackbody calibration target, then toward the Earth over the full range of incidence angles, and finally to cosmic microwave background radiation at 2.73 K. This enables precision end-to-end calibration of the millimeter-wave receivers during every 2-s scan period. The TEMPEST-D millimeter-wave radiometers are based on 35-nm indium phosphide (InP) high-electron-mobility transistor (HEMT) low-noise amplifiers. This article describes the instrument and its characterization prior to launch. [ABSTRACT FROM AUTHOR]

A low noise, high gain, stable radiometer front-end is presented for non-invasive tissue thermometry using custom designed narrow band low noise amplifiers (LNAs) and band pass filter (BPF) with 1.3 GHz centre frequency and − 20 dB pass band of 332 MHz. The fabricated LNAs have >15 dB gain, unconditional gain stability and noise figure (NF) < 1.45 dB in the pass band. The maximum insertion loss of the BPF is <1 dB over 1.2-1.4 GHz with 50 dB suppression in the surrounding communication bands. The cascaded radiometer front-end has measured gain of 45-50 dB, NF < 1.75 dB in the pass band and > 30 dB suppression in the adjacent personal communication bands. The Allan deviation of the total power radiometer indicates long term system stability and presence of Gaussian thermal noise for integration time, . Radiometer measurements of a matched load at room temperature for indicate acceptably low influence of external electromagnetic interference (EMI) and system noise equivalent temperature of 145 K. The brightness temperature measured by the total power radiometer using a resonant slot antenna demonstrates the ability to detect a 0.3°C change in the test load temperature with better than 0.1°C accuracy. [ABSTRACT FROM AUTHOR]

Methods to model snow aggregate scattering properties at microwave frequencies can be divided into structurally explicit and implicit techniques. Explicit techniques, such as the discrete dipole approximation (DDA), determine scattering and backscatter cross-sections assuming full knowledge of a given snow particle’s structure. Such calculations are computationally expensive. Implicit techniques, such as using the T-matrix method (TMM) with optically soft spheroids, model equivalent particles with variable mass, bulk density and aspect ratio according to an effective-medium approximation. It is highly desirable that there should be a good agreement between modeled aggregate cross-sections using both methods. A Voronoi bounding-neighbor algorithm is presented in this study to determine the bulk equivalent density of complex three-dimensional snow aggregates. While mass and aspect ratio are easily parameterized quantities, attempts to parameterize the bulk density of snowflakes have usually relied on a bounding ellipsoid, which can be determined from a flake’s radius of gyration, root mean square mean or simply from its maximum diameter. We compared the Voronoi algorithm against existing bounding spheroid approaches and mass–effective density relations at ten frequencies from 10.65 to 183.31 GHz, using a set of 1005 aggregates with maximum dimensions from a few hundred microns to several centimeters. When using the Voronoi-determined effective density, the asymmetry parameter, scattering, and backscatter cross-sections determined using the TMM reasonably match those for DDA-computed snow aggregates. From K u to W-band, soft spheroids can reproduce cross-sections for aggregates up to 9 mm in maximum dimension. Volume-integrated cross-sections always agree to within 25% of DDA. As the DDA is computationally expensive, this offers a fast alternative that efficiently evaluates scattering properties at microwave frequencies. [ABSTRACT FROM AUTHOR]

The joint National Aeronautics and Space Administration and Japanese Aerospace Exploration Agency (JAXA) Global Precipitation Measurement (GPM) mission will provide considerably more observations over complex and dynamically changing land backgrounds. A physically based precipitation retrieval using GPM's satellite constellation of passive microwave (PMW) observations has to accommodate the spatially and temporally varying radiometric signature of the land surface to constrain the set of candidate rainfall solutions. The challenge for retrieval algorithms is to identify and isolate precipitation profiles whose simulated observations agree with the satellite observations and are also representative of the surface conditions. Microwave emissivity modeling results are presented from a physically based land algorithm that retrieves soil moisture, vegetation water content, and surface temperature, along with the emissivity using polarized 10, 18, and 37 GHz channel measurements from the WindSat sensor onboard the Coriolis satellite, and results from the Tropical Rainfall Measuring Mission (TRMM) Microwave Imager (TMI). The emissivity mean, coefficient of variation, covariance, and correlation slope are examined for the range of clear-scene surface properties observed by WindSat and TRMM between 2003-2012 and 2002-2011, respectively, under a range of seasons, time of day, rain events, etc. These joint data provide a means to examine the extent to which the surface geophysical properties control the microwave land surface emissivity covariability, to better utilize these lower frequency observations in overland PMW-based precipitation retrievals. [ABSTRACT FROM PUBLISHER]

We present a new high-fidelity method of calibrating a cross-track scanning microwave radiometer using Global Positioning System (GPS) radio occultation (GPSRO) measurements. The radiometer and GPSRO receiver periodically observe the same volume of atmosphere near the Earth's limb, and these overlapping measurements are used to calibrate the radiometer. Performance analyses show that absolute calibration accuracy better than 0.25 K is achievable for temperature sounding channels in the 50-60-GHz band for a total-power radiometer using a weakly coupled noise diode for frequent calibration and proximal GPSRO measurements for infrequent (approximately daily) calibration. The method requires GPSRO penetration depth only down to the stratosphere, thus permitting the use of a relatively small GPS antenna. Furthermore, only coarse spacecraft angular knowledge (approximately one degree rms) is required for the technique, as more precise angular knowledge can be retrieved directly from the combined radiometer and GPSRO data, assuming that the radiometer angular sampling is uniform. These features make the technique particularly well suited for implementation on a low-cost CubeSat hosting both radiometer and GPSRO receiver systems on the same spacecraft. We describe a validation platform for this calibration method, the Microwave Radiometer Technology Acceleration (MiRaTA) CubeSat, currently in development for the National Aeronautics and Space Administration (NASA) Earth Science Technology Office. MiRaTA will fly a multiband radiometer and the Compact TEC/Atmosphere GPS Sensor in 2015. [ABSTRACT FROM PUBLISHER]

A prerequisite for the successful retrieval of geophysical parameters from remote sensing measurements is the development of an accurate forward model. The European Space Agency Soil Moisture and Ocean Salinity (SMOS), carrying onboard an L-band interferometric radiometer (Microwave Interferometric Radiometer using Aperture Synthesis), was launched on November 2009. Due to the lack of L-band passive ocean measurements from space, several prelaunch forward models were developed and initially used in the SMOS ocean salinity operational processor. In this paper, an update of the prelaunch semi-empirical forward model is presented, using for the first time, real SMOS data. In particular, the ocean surface emissivity modulation at L-band due to rough sea surface is reviewed and reanalyzed. A new model definition is provided with the help of a simple neural network. The improvement is quantified in terms of retrieved salinity accuracy compared with the climatology and concerns essentially the range of wind speeds higher than 12 m·s-1. [ABSTRACT FROM AUTHOR]

Several soil moisture and sea salinity campaigns, including airborne L-band radiometer measurements, have been carried out in preparation for the European Space Agency Soil Moisture and Ocean Salinity (SMOS) mission. The radiometer used in this context is fully polarimetric and is capable of detecting radio frequency interference (RFI) using the kurtosis method. Analyses have shown that the kurtosis method generally detects RFI in an efficient manner, particularly concerning pulsed, low duty cycle signals, but it has some shortcomings when it comes to more continuous wave signal types. Hence, other detection methods have been investigated as well. In particular, inspection of the third and fourth Stokes parameters shows promising results-possibly as a complement to the kurtosis method. The kurtosis method, however, cannot be used with SMOS data. Since SMOS is fully polarimetric, the third and fourth Stokes parameter method is an option, and a first assessment using a fully polarimetric SMOS data set looks promising. Finally, a variable incidence angle signature algorithm is introduced, and the possibility of using this as an RFI indicator is discussed. [ABSTRACT FROM PUBLISHER]

In support of the European Space Agency Soil Moisture and Ocean Salinity (SMOS) mission, a number of soil moisture and sea salinity campaigns, including airborne L-band radiometer measurements, have been carried out. The radiometer used in this context is fully polarimetric and has built-in radio-frequency-interference (RFI)-detection capabilities. Thus, the instrument, in addition to supplying L-band data to the geophysicists, also gave valuable information about the RFI environment. Campaigns were carried out in Australia and in a variety of European locations, resulting in the largest and most comprehensive data set available for assessing RFI at L-band. This paper introduces the radiometer system and how it detects RFI using the kurtosis method, reports on the percentage of data that are typically flagged as being corrupted by RFI, and gives a hint about geographical distribution. Also, examples of polarimetric signatures are given, and the possibility of detecting RFI using such data is discussed. [ABSTRACT FROM AUTHOR]

In support of the European Space Agency Soil Moisture and Ocean Salinity (SMOS) mission, a number of soil moisture and sea salinity campaigns, including airborne L-band radiometer measurements, have been carried out. The radiometer used in this context is fully polarimetric and has built-in radio-frequency-interference (RFI)-detection capabilities. Thus, the instrument, in addition to supplying L-band data to the geophysicists, also gave valuable information about the RFI environment. Campaigns were carried out in Australia and in a variety of European locations, resulting in the largest and most comprehensive data set available for assessing RFI at L-band. This paper introduces the radiometer system and how it detects RFI using the kurtosis method, reports on the percentage of data that are typically flagged as being corrupted by RFI, and gives a hint about geographical distribution. Also, examples of polarimetric signatures are given, and the possibility of detecting RFI using such data is discussed. [ABSTRACT FROM AUTHOR]

L-band (1-2 GHz) microwave radiometry is a remote sensing technique that can be used to monitor soil moisture, and is deployed in the Soil Moisture and Ocean Salinity (SMOS) Mission of the European Space Agency (ESA). Performing ground-based radiometer campaigns before launch, during the commissioning phase and during the operative SMOS mission is important for validating the satellite data and for the further improvement of the radiative transfer models used in the soil-moisture retrieval algorithms. To address these needs, three identical L-band radiometer systems were ordered by ESA. They rely on the proven architecture of the ETH L-Band radiometer for soil moisture research (ELBARA) with major improvements in the microwave electronics, the internal calibration sources, the data acquisition, the user interface, and the mechanics. The purpose of this paper is to describe the design of the instruments and the main characteristics that are relevant for the user. [ABSTRACT FROM AUTHOR]

Two semiconductor active cold loads (ACLs) to be used as cold references in spaceborne microwave radiometers have been developed. An X-band frequency was chosen, and the target noise temperature value was in the 50-100-K range. The ACLs are characterized in the operating temperature range of 0 °C-50 °C and long-term stability is assessed. To this end, a test bed has been developed. This test bed is actually a stable radiometer, and its design and performance are discussed. The test setup is described, and test campaign results indicate output temperatures of 77 and 56 K for the two ACLs. The temperature sensitivity is slightly below 0.4 K/°C for the units, and long-term stability within 2 K/year is observed. [ABSTRACT FROM AUTHOR]

Analyses and results of the radiometric calibration accuracy and measurement characteristics of the first Defense Meteorological Satellite Program (DMSP)'s Special Sensor Microwave Imager/Sounder (SSMIS) upper atmosphere sounding (UAS) channels are presented herein. Launched on October 18, 2003, aboard the DMSP F-16 spacecraft in a sun-synchronous orbit, the SSMIS UAS channels provide the first operational measurements of microwave radiation emitted by the Earth's atmosphere at mesospheric altitudes. The analysis of the SSMIS radiometer absolute calibration and stability is based upon extensive comparisons with a fully polarimetric radiative transfer model (RTM) that solves for all four Stokes parameters using coincident atmospheric temperature profiles derived from collocated Rayleigh lidar observations merged with the European Centre for Medium-Range Weather Forecasting temperature analyses and climatological data sets. The resulting merged profiles provide a physically consistent temperature profile from the surface to 100 km, as needed by the RTMs. The results presented herein of the SSMIS instrument show that significant hardware and scientific technical challenges arise from microwave temperature sounding of the mesosphere. These include the following: 1) addressing the impact of large noise-equivalent temperature difference associated with narrow channel bandwidths; 2) achieving high channel center-frequency stability; 3) compensation of large spacecraft-induced Doppler shift; 4) better characterization of the Zeeman splitting of the oxygen absorption lines; 5) development of a fast polarimetric RTM; and 6) designing stable and accurate on-orbit radiometric calibration targets. Results to date show that the uncertainties of the calibration accuracy of the SSMIS UAS channels are consistent and in agreement with the limits derived for the SSMIS UAS channels and with the simulated radiances derived from the merged lidar profiles. [ABSTRACT FROM AUTHOR]

Ten underflights of the Special Sensor Microwave Imager/Sounder (SSMIS) with Conical Scanning Millimeter-wave Imaging Radiometer (CoSMIR) onboard the NASA ER-2 aircraft were conducted over the coastal region of California between March 2004 and March 2005. The measured brightness temperature (Tb) values from both sensors are collocated and compared at frequencies of 50.3, 52.8, 53.6, 91.655, 150, 183.3 ± 1,183.3 ± 3, and 183.3 ± 6.6 GHz. The more transparent channels at 50.3, 91.655, and 150 GHz are strongly affected by the changes in surface emission and low-level liquid clouds. Thus, the average differences in Tb values (δTb), measured by the two sensors, and their changes from flight to flight are difficult to assess. For the remaining opaque channels, using the CoSMIR measurements as reference, the lowest SSMIS Tb values occur when the SSMIS is completely under the Earth's shadow. As the satellite moves out of the Earth's shadow in the ascending passes, the SSMIS Tb values are found to gradually increase with more exposure to the sun. The magnitudes of these Tb changes are about 4-5 K for the three 183.3-GHz channels and about 2 K for the 52.8- and 53.6-GHz channels. [ABSTRACT FROM AUTHOR]

Abstract: Optimal deconvolution (ODC) utilizes the footprint overlap in microwave observations to estimate the earth''s brightness temperatures (T B). This paper examines the accuracy of ODC-estimated T B compared with a standard averaging technique. Because brightness temperatures cannot be independently verified, we constructed synthetic True T B for accuracy assessment. We assigned T B at a high spatial resolution (1 km) grid and computed the True T B by spatial averaging of the assigned T B to a lower resolution earth grid (25 km), selected to match the resolution of products generated from the Advanced Microwave Scanning Radiometer for the Earth Observing System (AMSR-E). We used the sensor antenna response function along with the 1-km assigned T B to generate synthetic observations at AMSR-E footprint locations. These synthetic observations were subsequently deconvolved in the ODC technique to estimate T B at the lower resolution earth grid. The ODC-estimated T B and the simple grid cell averages of the synthetic observations were compared with the True T B allowing us to quantify the efficacy of each technique. In areas of high T B contrast (such as boundaries of water bodies), ODC performed significantly better than averaging. In other areas, ODC and averaging techniques produced similar results. A technique similar to ODC can be effective in delineating water bodies with significant clarity. That will allow microwave observations to be utilized near the shorelines, a trouble spot for the currently used averaging techniques. [Copyright &y& Elsevier]

In the present study, remote sensing of soil moisture is carried out using the Passive and Active L- and S-band airborne sensor (PALS). The data in this paper were taken from five days of overflights near Chickasha, OK during the 1999 Southern Great Plains (SGP99) experiment. Presently, we analyze the collected data to understand the relationships between the observed signals (radiometer brightness temperature and radar backscatter) and surface parameters (surface soil moisture, temperature, vegetation water content, and roughness). In addition, a radiative transfer model and two radar backscatter models are used to simulate the PALS observations. An integration of observations, regression retrievals, and forward modeling is used to derive the best estimates of soil moisture under varying surface conditions. [ABSTRACT FROM AUTHOR]

The Global Precipitation Measurement (GPM) Dual-Frequency Precipitation Radar (DPR) (Ku- and Ka-band, or 14 and 35 GHz) provides the capability to resolve the precipitation structure under moderate to heavy precipitation conditions. In this manuscript, the use of near-coincident observations between GPM and the CloudSat Profiling Radar (CPR) (W-band, or 94 GHz) are demonstrated to extend the capability of representing light rain and cold-season precipitation from DPR and the GPM passive microwave constellation sensors. These unique triple-frequency data have opened up applications related to cold-season precipitation, ice microphysics, and light rainfall and surface emissivity effects. [ABSTRACT FROM AUTHOR]

Offshore of many coastal regions, the ocean surface wind varies in speed and direction throughout the day, owing to forcing from land/sea temperature differences and orographic effects. Far offshore, both diurnal and semidiurnal wind vector variability has been noted in the Tropical Atmosphere Ocean-TRIangle Trans-Ocean buoy Network (TAO-TRITON) mooring data in the tropical Pacific Ocean. In this manuscript, the tropical diurnal wind variability is examined with microwave radiometer-derived winds from the Tropical Rainfall Measuring Mission (TRMM) and the Global Precipitation Measurement (GPM), merged with RapidScat and other scatterometer data. Since the relationship between wind speed and its zonal and meridional components is nonlinear, this manuscript describes an observationally based methodology to merge the radiometer and scatterometer-based wind estimates as a function of observation time, to generate a multi-year dataset of diurnal wind variability. Compared to TAO-TRITON mooring array data, the merged satellite-derived wind components fairly well replicate the semidiurnal zonal wind variability over the tropical Pacific but generally show more variability in the meridional wind components. The meridional component agrees with the associated mooring location data in some locations better than others, or it shows no clear dominant diurnal or semidiurnal mode. Similar discrepancies are noted between two forecast model reanalysis products. It is hypothesized that the discrepancies amongst the meridional winds are due to interactions between surface convergence and convective precipitation over tropical ocean basins. [ABSTRACT FROM AUTHOR]

A low-mass and low-volume dual-polarization L-band radiometer is introduced that has applications for ground-based remote sensing or unmanned aerial vehicle (UAV)-based mapping. With prominent use aboard the ESA Soil Moisture and Ocean Salinity (SMOS) and NASA Soil Moisture Active Passive (SMAP) satellites, L-band radiometry can be used to retrieve environmental parameters, including soil moisture, sea surface salinity, snow liquid water content, snow density, vegetation optical depth, etc. The design and testing of the air-gapped patch array antenna is introduced and is shown to provide a 3-dB full power beamwidth of 37°. We present the radio-frequency (RF) front end design, which uses direct detection architecture and a square-law power detector. Calibration is performed using two internal references, including a matched resistive source (RS) at ambient temperature and an active cold source (ACS). The radio-frequency (RF) front end does not require temperature stabilization, due to characterization of the ACS noise temperature by sky measurements. The ACS characterization procedure is presented. The noise equivalent delta (Δ) temperature (NEΔT) of the radiometer is ~0.14 K at 1 s integration time. The total antenna temperature uncertainty ranges from 0.6 to 1.5 K. [ABSTRACT FROM AUTHOR]

This paper presents the broadband antenna for the microwave radiometric sensing of internal body temperature. For broadband operation, the bow-tie antenna was designed and backed with a cylindrical cavity, which decreased environmental electromagnetic interference and also improved the directivity of the antenna. The broadband impedance-transforming balun in microstrip form was also designed to feed the bow-tie antenna, and was located inside the cavity. An impedance-matching dielectric layer (IMDL) was introduced on top of the bow-tie antenna, for impedance match with the human body with high permittivity. The fabricated antenna was measured in free space with the IMDL removed, showing an input reflection coefficient lower than −10 dB from 2.64 to > 3.60 GHz with antenna gain over 6.0 dBi and radiation efficiency over 74.7% from 2.7 to 3.5 GHz. The IMDL was re-installed on the cavity-backed bow-tie antenna to measure the antenna performance for the human head with relative permittivity of about 40. The measured reflection coefficient was as low as −28.9 dB at 2.95 GHz and lower than −10 dB from 2.65 to > 3.5 GHz. It was also shown that the designed antenna recovered a good impedance match by adjusting the permittivity and thickness of the IMDL for the different parts of the human body with different permittivities. [ABSTRACT FROM AUTHOR]

Accurate representation of the ocean-atmosphere coupling in weather, wave and climate models requires reliable estimates of air-sea surface fluxes of momentum, heat and mass. Whitecap fraction (W) usually quantifies the enhancement of the surface fluxes due to wave breaking. Satellite-based passive remote sensing of W from ocean surface brightness temperatures ( T B s) observes open ocean surface fluxes at low spatial resolution. Radiometric surface observations at higher resolution are necessary to monitor the complex environment in the coastal zone and in polar regions. We assess the feasibility of using the millimeter-wave frequencies (89 to 150 GHz) to observe whitecaps. We evaluate the derivative of the T B with respect to W as a measure for the observation of W. We describe the models and data used to evaluate the T B sensitivity to W for different instrumental and environmental conditions. Atmospheric absorption limits the ability to observe the surface at millimeter-wave frequencies. We find that the T B sensitivity to W at 89 GHz may be sufficient to support limited W retrieval from observations at altitudes below 1 km and that the T B sensitivity at 113 and 150 GHz is not sufficient. Clear skies, and low to moderate atmospheric humidity favor whitecap observations. [ABSTRACT FROM AUTHOR]