Search

Dynamic X-ray elastography using propagating shear waves is a novel technique to visualize the spatial distribution of elasticity in soft materials. We demonstrate that it can be applied to a gel sample with a fine structure. We prepared a viscoelastic gel sample with a two-dimensional lattice structure filled with ZrO2 particles, and applied the technique to map storage and loss moduli. The obtained storage modulus map successfully distinguished the harder lattice structure from the soft gel matrix with a spatial resolution much higher than those of other conventional elastography techniques using magnetic resonance and ultrasound.

This study aimed to develop a refined actuator suitable for psoas major muscle (PM) MR elastography (MRE) and evaluate its measurement precision. MRE was performed on nine healthy volunteers. Discomfort under PM-MRE examinations was evaluated by discomfort scores using a four-point subjective scale. The performance of refined actuator was evaluated in detail; repeatability was evaluated using repeatability coefficients (%RC) according to the Quantitative Imaging Biomarker Alliance (QIBA) and reproducibility with different operators was evaluated using interclass correlation coefficients (ICC). The discomfort score was 1.4 ± 0.53 and it indicated refined actuator was sufficiently comfortable (no pain). In the repeatability study (n = 9), the %RC was approximately 19%, which was comparable to the limit required for clinical liver MREs by the QIBA (19%). In the reproducibility study, the ICCs were > 0.90 (n = 3), indicating that the refined actuator had almost perfect reproducibility. The refined actuator was suitable for PM-MREs and had acceptable repeatability and reproducibility. Refined actuator was expected to meet the standard set by the QIBA (for liver MRE).

Magnetic resonance elastography (MRE) can visualize the shear wave propagation of in vivo tissues, which can be mapped into viscoelastic properties. No study has measured the biomechanical properties of the PM muscle in vivo using MRE. In this study, we evaluated stiffness values calculated by local frequency estimate (LFE) and algebraic inversion of differential equation (AIDE) in PM-MRE. The PM muscles of 17 healthy male volunteers were scanned in supine position by MRE. The Laplacian-based estimate (LBE) phase wrapped image data were filtered by gaussian-bandpass filter (GBF), and by both directional and GBF. LFE (MREWave) and AIDE wave inversion methods were used to calculate the respective elastograms. The wave interferences were removed by directional filtering, and smooth wave fields were obtained. The stiffness values calculated by LFE of non-DF images were 1.39 ± 0.25 kPa and 1.33 ± 0.22 kPa for right and left PM respectively, whereas for DF images, they were 1.26 ± 0.20 kPa for right PM and 1.18 ± 0.28 kPa for left PM. The stiffness values calculated by AIDE of non-DF images were 0.78 ± 0.10 kPa and 0.78 ± 0.13 kPa for right and left PM respectively, whereas for DF images, they were 0.73 ± 0.12 kPa for right PM and 0.74 ± 0.11 kPa for left PM. There was no statistically significant difference in mean values of stiffness with/without applying directional filter whereas there was a statistically significant difference in mean values of stiffness between LFE and AIDE. Both LFE and AIDE could be used for psoas major MR Elastography.

The present study aimed to develop vibration techniques for magnetic resonance (MR) elastography (MRE) of the psoas major muscle (PM). Seven healthy volunteers were included. MRE was performed with motion-encoding gradient (MEG)-less multi-echo MRE sequence, which allows clinicians to perform MRE using conventional MR imaging. In order to transmit mechanical vibration of the pneumatic type to the PM, a long narrow vibration pad was designed using a 3D printer, and the optimum vibration techniques were verified. The vibration pad was placed under the lower back, with the volunteers in the supine position. The results indicated that the PM vibrated well through the transmitted vibration from the lumbar spine, which suggests that the placement of a narrow vibration pad under the supine body, along the lumbar spine, allows the vibration of the PM. The shear modulus of the PM (n = 7) was 1.23 ± 0.09 kPa (mean ± SEM) on the right side and 1.22 ± 0.15 kPa on the left side, with no significant difference (t-test, P > 0.05). Increased stiffness of the muscle due to continuous local contraction may be an important cause of non-specific low back pain (LBP). The present vibration techniques for MRE of the PM provide a quantitative diagnostic tool for changes in muscle stiffness associated with non-specific LBP.

This study aims to develop and assess a new automated processing technique in MR elastography (MRE), namely coherent-wave auto-selection (CHASE). CHASE enables automatic selection of the region of interest (ROI) for stiffness measurement by extraction of the coherent wave region (CHASE ROI), and it improves the reconstruction of stiffness by a directional filter oriented along the main wave in each pixel (CHASE filtering). In this study, MRE of a phantom and of the liver of four healthy volunteers was performed. To investigate the potential of CHASE, this study assessed the CHASE according to three indices through the phantom study: 1) agreement on the ROI settings between CHASE and expert observers, 2) noise dependency, and 3) effect of the CHASE on stiffness variability within the CHASE ROI. The agreements on the ROI settings were analyzed by Cohen's kappa coefficient (κ). The noise dependency was analyzed by the mean absolute percentage errors (MAPEs) within the ROI between low (20%-80% amplitudes) and high vibration amplitudes (100% amplitude). The stiffness variability was assessed by standard deviation (SD) within the ROI. In the volunteer study, agreements on the ROI settings (or stiffness value) and stiffness variability within the CHASE ROI were assessed using κ-value (or intraclass correlation coefficient: ICC) and coefficient of variation, respectively. The results showed close agreement on the ROI settings and stiffness (κ-value: greater than 0.61 in both the phantom and volunteer studies, ICC: 0.97 in the volunteer study). The MAPEs within the CHASE ROI were much smaller than those in the whole region of the phantom (CHASE ROI vs. the whole region at 20% amplitude: 10.3% vs. 50.8%). Moreover, in both the phantom and volunteer studies, the stiffness variation within the CHASE ROI was smaller in the elastogram processed with CHASE filtering than in the unprocessed one. Our results demonstrated that the CHASE has high robustness against noise and the potential to provide ROI settings for stiffness measurement comparable to expert observers, as well as improve the reconstruction of stiffness.

The purpose of this study was to investigate an influence of vibration waveform on magnetic resonance elastography (MRE). MRE is an innovative imaging technique for the non-invasive quantification of the elasticity of soft tissues through the direct visualization of propagating shear waves in vivo using a special phase-contrast magnetic resonance imaging sequence. Since the elasticity of soft tissue calculates from the wavelength of propagating shear waves, it is necessary to propagate sine-wave-shape shear wave at the target soft tissue. However, due to the various factors; i.e. overload of vibration generator, poor contact between imaging object and vibration pad, etc.; it may be difficult to generate a simple sine wave. This work was focused on change vibration waveforms; i.e. square wave, triangle wave, saw-tooth wave; which is induced by the various factors. Phantom experimental results demonstrated that when square and saw-tooth waveforms of 25 Hz vibration frequency, into the phantom, the waveform of propagating wave was not similar to sine waveform. It may influence on the MRE that in case of the waveforms has low frequency and square or saw-tooth like waveforms.

Palpation is a standard clinical tool to diagnose abnormal stiffness changes in soft tissues. However, it is difficult to palpate the supraspinatus muscle because it locates under the trapezius muscle. The magnetic resonance elastography (MRE) uses harmonic mechanical excitation to quantitatively measure the stiffness (shear modulus) of both the superficial and deep tissues. The purpose of this study was to build a vibration system for applying the MRE to the supraspinatus muscle. In this study, a power amplifier and a pneumatic pressure generator were used to supply vibrations to a vibration pad. Six healthy volunteers underwent MRE. We investigated the effects of position (the head of the humerus and the trapezius muscle) of the vibration pad on the patterns of wave propagation (wave image). When the vibration pad was placed in the trapezius muscle, the wave images represented clear wave propagation. On the other hand, when the vibration pad was placed in the head of the humerus, the wave images represented unclear wave propagation. This result might be caused by wave interferences resulting from the vibrations from bones and an intramuscular tendon of the supraspinatus muscle. The mean shear modulus also was 8.12 ± 1.83 (mean ± SD) kPa, when the vibration pad was placed in the trapezius muscle. Our results demonstrated that the vibration pad should be placed in the trapezius muscle in the MRE of the supraspinatus muscle.

Magnetic resonance elastography (MRE) can measure tissue stiffness quantitatively and noninvasively. Supraspinatus muscle injury is a significant problem among throwing athletes. The purpose of this study was to develop an MRE technique for application to the supraspinatus muscle by using a conventional magnetic resonance imaging (MRI). MRE acquisitions were performed with a gradient-echo type multi-echo MR sequence at 100 Hz pneumatic vibration. A custom-designed vibration pad was used as a pneumatic transducer in order to adapt to individual shoulder shapes. In a gradient-echo type multi-echo MR sequence, without motion encoding gradient (MEG) that synchronizes with vibrations, bipolar readout gradient lobes achieved a similar function to MEG (MEG-like effect). In other words, a dedicated MRE sequence (built-in MEG) is not always necessary for MRE. In this study, 7 healthy volunteers underwent MRE. We investigated the effects of direction of the MEG-like effect and selected imaging planes on the patterns of wave propagation (wave image). The results indicated that wave images showed clear wave propagation on a condition that the direction of the MEG-like effect was nearly perpendicular to the long axis of the supraspinatus muscle, and that the imaging plane was superior to the proximal supraspinatus muscle. This limited condition might be ascribed to specific features of fibers in the supraspinatus muscle and wave reflection from the boundaries of the supraspinous fossa. The mean stiffness of the supraspinatus muscle was 10.6 ± 3.17 kPa. Our results demonstrated that using MRE, our method can be applied to the supraspinatus muscle by using conventional MRI.

In cartilage regenerative medicine, autologous chondrocyte implantation (ACI) has been applied clinically for partial defects of joint cartilage or nasal augmentation. To make treatment with ACI more effective and prevalent, modalities to evaluate the quality of transplanted constructs noninvasively are necessary. In this study, we compared the efficacy of several noninvasive modalities for evaluating the maturation of tissue-engineered auricular cartilage containing a biodegradable polymer scaffold. We first transplanted tissue-engineered cartilage consisting of human auricular chondrocytes, atelocollagen gel, and a poly-l-lactic acid (PLLA) porous scaffold subcutaneously into the back of athymic nude rats. Eight weeks after transplantation, the rats were examined by magnetic resonance imaging (MRI), X-ray, and ultrasound as noninvasive modalities. Then, the excised constructs were examined by histological and biochemical analysis including toluidine blue (TB) staining, glycosaminoglycans content, and enzyme-linked immunosorbent assay of type II collagen. Among the modalities examined, transverse relaxation time (T2) and apparent diffusion coefficient of MRI showed quite a high correlation with histological and biochemical results, suggesting that these can effectively detect the maturation of tissue-engineered auricular cartilage. Since these noninvasive modalities would realize time-course analysis of the maturation of tissue-engineered auricular cartilage, this study provides a substantial insight for improving the quality of tissue-engineered cartilage, leading to improvement of the quality and technique in cartilage regenerative medicine.

We measured standard deviation (SD), noise power spectrum (NPS), and modulation transfer function (MTF) of computed tomography obtained by image summation method (fused CT) using phantoms. SDs, NPSs and MTFs of fused CT up to 25 times summation were calculated. Increased number of image summation reduced SD and NPS, although the effect became small after 10 times summation. MTF remained the same regardless of the number of summation. Fused CT is effective in reducing noise.

The speed of sound (SOS) of a longitudinal wave propagating in the living body reflects the tissue properties and is expected as a promising evaluation index for detection of disease, diagnosis and monitoring. However, in general, the interpretation of SOS is complex, because it is influenced mostly by compressibility and multiple factors. In this study, as a study for the interpretation of SOS, the SOS of cartilage was measured in vivo by using a fusion of ultrasound and magnetic resonance imaging (MRI), and the correlations between the SOS and other quantities were investigated. In summary, as a possible interpretation of SOS of cartilage tissue used in this study, it was suggested that the SOS was partly related to water content.

We developed a Magnetic Resonance elastography (MRE) technique using a conventional magnetic resonance imaging (MRI), which allows a simultaneous elastography of the supraspinatus and trapezius muscles, by designing a new wave transducer (vibration pad) and optimizing the mechanical vibration frequency. Five healthy volunteers underwent an MRE. In order to transmit the mechanical vibration (pneumatic vibration) to the supraspinatus and trapezius muscles, a new vibration pad was designed using a three-dimensional (3D) printer. The vibration pad was placed on the skin 2 cm medial and 2 cm cephalad the deltoid tubercle. MRE acquisition was performed with a multi-slice gradient-echo type multi-echo MR sequence, which allows MREs even in a conventional MRI; two oblique axial images of the supraspinatus and trapezius muscles were obtained simultaneously. Vibration frequencies were set at 50–150 Hz, with a 25 Hz step. Wave image quality in each frequency was analyzed using a phase-to-noise ratio (PNR) and clarity of propagating wave that was assessed by two readers qualitatively. In the supraspinatus muscle, the wave images were of good quality especially at frequencies >75 Hz. In the trapezius muscle, the wave images were of better quality at low frequencies (50 and 75 Hz) compared with high frequencies (100–150 Hz). The PNR of both muscles were higher at low frequencies. The mean stiffness in the trapezius muscle (7.26 ± 2.13 kPa at 75 Hz) was larger than those in the supraspinatus muscle (4.16 ± 0.50 kPa at 75 Hz). The results demonstrated that our MRE technique allows simultaneous assessment of the stiffness in the supraspinatus and trapezius muscles using a conventional MRI, and that optimal vibration frequency for simultaneous MRE of these muscles is 75 Hz. This technique provides a new means for early detection of abnormality in the shoulder.

Diffusion-magnetic resonance elastography (dMRE) is an emerging practical technique that can acquire diffusion magnetic resonance imaging and MRE simultaneously. However, a signal loss attributable to intravoxel phase dispersion (IVPD) interferes with the calculation of the apparent diffusion coefficient (ADC). This study presents an approach to dMRE that reduces the influence of IVPD by introducing a new pulse sequence. The existing and proposed techniques were performed using a phantom comprising five rods with different elasticities at 60 Hz vibration to investigate the accuracy of previous and proposed dMRE techniques. The measures of ADC and stiffness, obtained by using both dMRE techniques, were compared with conventional spin-echo (SE) diffusion and SE-MRE. Then, we evaluated those differences by using the mean of absolute differences (MAD) in each rod within the phantom. The results of the MAD of the stiffness from both dMRE techniques showed almost no difference. In contrast, the value of the ADC MAD (MAD ≒ 0.16 × 10−3 mm2/s), obtained in the soft region within the phantom with the previous dMRE technique, was large. This value was about 2.7 times that of the value produced by the proposed dMRE technique. This difference must reflect the degree of influence of IVPD in both techniques. These results demonstrate that our dMRE technique is a robust method for addressing the signal loss attributable to IVPD.

To demonstrate the feasibility of a novel MR elastography (MRE) technique based on a conventional gradient-echo type multi-echo MR sequence which does not need additional bipolar magnetic field gradients (motion encoding gradient: MEG), yet is sensitive to vibration. In a gradient-echo type multi-echo MR sequence, several images are produced from each echo of the train with different echo times (TEs). If these echoes are synchronized with the vibration, each readout's gradient lobes achieve a MEG-like effect, and the later generated echo causes a greater MEG-like effect. The sequence was tested for the tissue-mimicking agarose gel phantoms and the psoas major muscles of healthy volunteers. It was confirmed that the readout gradient lobes caused an MEG-like effect and the later TE images had higher sensitivity to vibrations. The magnitude image of later generated echo suffered the T2 decay and the susceptibility artifacts, but the wave image and elastogram of later generated echo were unaffected by these effects. In in vivo experiments, this method was able to measure the mean shear modulus of the psoas major muscle. From the results of phantom experiments and volunteer studies, it was shown that this method has clinical application potential.

We aimed to investigate the association between mobility and skeletal muscle strength by using magnetic resonance diffusion tensor imaging (DTI). This study included 20 healthy male volunteers (mean age, 21.8 ± 1.1 years). The maximum voluntary strength (MVC) of each participant was measured with the ankle joint in plantar and dorsal flexion using an instrument for measuring muscle strength. Moreover, magnetic resonance imaging (MRI) was performed with the ankle joint at rest, in plantar flexion, and in dorsal flexion. For imaging, a 1.5-T MRI device was used, and a diffusion-weighted stimulated echo-planar imaging pulse sequence. Tensor eigenvalues (λ), fractional anisotropy (FA), and the apparent diffusion coefficient (ADC) were calculated from data obtained by DTI. The resulting MRI data were compared to the data on muscle mobility or strength and statistically analyzed. Regarding changes in DTI indices during muscle movements, anisotropy of the tibialis anterior was significantly increased from rest to plantar flexion (P < 0.01), whereas no significant change was observed in dorsal flexion (n.s.). In contrast, the extent of significant changes in anisotropy of the medial gastrocnemius (mGC) and soleus (SOL) was small at plantar flexion (mGC, P < 0.01; SOL, n.s.), whereas the indices were significantly increased at dorsal flexion (P < 0.01). Regarding the correlation between MVC of each skeletal muscle and the DTI indices, FA and λ3 were significantly correlated in movements involving the muscles, whereas no significant correlation was observed in movements not involving them. Changes in intramuscular water molecules by elongation and contraction of the skeletal muscle fibers could be assumed to affect changes in diffusional anisotropy. When muscles contract, the space between myocytes was reduced and they might become increasingly dense. Moreover, diffusional anisotropy increased with increasing MVC, whereas ADC remained unchanged. DTI was suggested to produce measurements similar to the degree of muscle strength.

Background 18q-Syndrome is a chromosomal disorder exhibiting various symptoms arising from the central nervous system. Brain magnetic resonance imaging (MRI) of patients with this syndrome usually demonstrates abnormal white matter intensities. This is widely believed to be due to impaired myelin formation because this syndrome involves the deletion of the myelin basic protein (MBP) gene in 18q23. However, this hypothesis has not been confirmed by actual pathology because early death is unusual and autopsy rarely performed. Patient A 6-year-old boy with ring chromosome 18 syndrome was examined by genetic analysis for the MBP gene, brain MRI, and autopsy. Results Haploinsufficiency of the MBP gene was confirmed. T2-weighted MRI revealed diffuse high intensities throughout the cerebral white matter. Pathological examination showed the cerebral white matter to be uniformly stained by Kluver–Barrera and MBP immunohistochemical staining. Oligodendrocytes were immunoreactive for proteolipid protein and ferritin but not MBP. Electron microscopy revealed clusters of axons wrapped in compact myelin sheaths with distinct major dense lines. Holzer and immunohistochemical staining for glial fibrillary acidic protein showed extensive staining of the white matter and an increased number of glial filaments. Conclusions This pathological study demonstrated that in this disorder, the brain was well myelinated, contrary to established hypotheses about this disorder. The MRI signal abnormalities in 18q-syndrome could be attributed to gliosis and not to dysmyelination.

It is important to evaluate the elasticity of tissue-engineered cartilage, for evaluating its structural strength. However, in vivo evaluation of tissue-engineered cartilage elasticity has not been established. On the other hand, since the speed of sound (SOS) is available for elasticity evaluation, we have proposed in vivo measurement method of SOS using ultrasound and MR images. This method determines the SOS based on the thickness measurement using the MR image and the time-of-flight (TOF) measurement using the ultrasound. In this study, this method was applied to the SOS measurement in tissue-engineered cartilage, and then relation between in vivo SOS and elasticity was investigated. As the result, in vivo SOS had a high correlation with Young's modulus. This result reveals that in vivo evaluation of tissue-engineered cartilage elasticity is available through in vivo SOS measurement.

In order to detect the disease and degeneration of cartilage early, evaluations of acoustic properties are expected, but the physical meaning should be clarified. On the other hand, we have proposed a multimodal method using ultrasound (US) and magnetic resonance (MR) images for in vivo SOS measurement. In this study, the method was applied for the tissue-engineered cartilage, and the SOS was compared with T1, T2, apparent diffusion coefficient (ADC), attenuation coefficient (ATT), and Young’s modulus (YM). All procedures were approved by the Animal Care and Use Committee of our institution. 12-week-old male rats were used, and five different types of tissue-engineered cartilage was subcutaneously implanted in the back of rat (n = 30). Under anesthesia, MR and US images including same cross-sections were acquired separately, by using a MR imager of 2 Tesla and a US device of 13 MHz. At this time, T1, T2, ADC were also measured. The SOS was determined by the thickness measurement using the MR image and the...

The purpose of this study was to develop a new technique for a powerful compact MR elastography (MRE) actuator based on a pneumatic ball-vibrator. This is a compact actuator that generates powerful centrifugal force vibrations via high speed revolutions of an internal ball using compressed air. This equipment is easy to handle due to its simple principles and structure. Vibration frequency and centrifugal force are freely adjustable via air pressure changes (air flow volume), and replacement of the internal ball. In order to achieve MRI compatibility, all parts were constructed from non-ferromagnetic materials. Vibration amplitudes (displacements) were measured optically by a laser displacement sensor. From a bench test of displacement, even though the vibration frequency increased, the amount of displacement did not decrease. An essential step in MRE is the generation of mechanical waves within tissue via an actuator, and MRE sequences are synchronized to several phase offsets of vibration. In this system, the phase offset was detected by a four-channel optical-fiber sensor, and it was used as an MRI trigger signal. In an agarose gel phantom experiment, this actuator was used to make an MR elastogram. This study shows that the use of a ball actuator for MRE is feasible.

The purpose of this study was to examine the potential of diffusion-weighted (DW) three-dimensional (3D) MP-RAGE sequence for cerebral ischemia of a rat brain in vivo. The prototype of a DW-3D-MP-RAGE (3D-DWI) sequence was implemented at 2.0T animal experiment MR imager. The advantage of 3D imaging are that you obtain thinner and more slices with better profiles, and better signal-to-noise ratio for an equivalent slice thickness. Since 3D imaging is preferable for obtaining contiguous thin-slice MR images, image data with 3D imaging are expected to volume estimate of imaging area. Three-dimensional calculated absolute apparent diffusion coefficient (ADC) maps were compared with coronal stained (triphenyltetrazolium chloride: TTC) brain sections. From rat experimental results, the region of cerebral ischemia with 3D-DWI and the region of stained brain sections were well in agreement. This technique enables three-dimensional image display of a cerebral ischemia area, and makes it possible to measure the volume of a precise cerebral ischemia area in vivo., Date of Conference: Oct. 30 2010-Nov. 6 2010

Applying tissue-engineered cartilage in a clinical setting requires noninvasive evaluation to detect the maturity of the cartilage. Magnetic resonance imaging (MRI) of articular cartilage has been widely accepted and applied clinically in recent years. In this study, we evaluated the negative fixed-charge density (nFCD) of tissue-engineered cartilage using gadolinium-enhanced MRI and determined the relationship between nFCD and biomechanical properties. To reconstruct cartilage tissue, articular chondrocytes from bovine humeral heads were embedded in agarose gel and cultured in vitro for up to 4 weeks. The nFCD of the cartilage was determined using the MRI gadolinium exclusion method. The equilibrium modulus was determined using a compressive stress relaxation test, and the dynamic modulus was determined by a dynamic compression test. The equilibrium compressive modulus and dynamic modulus of the tissue-engineered cartilage increased with an increase in culture time. The nFCD value—as determined with the [Gd-DTPA2−] measurement using the MRI technique—increased with culture time. In the regression analysis, nFCD showed significant correlations with equilibrium compressive modulus and dynamic modulus. From these results, gadolinium-enhanced MRI measurements can serve as a useful predictor of the biomechanical properties of tissue-engineered cartilage.

The application of tissue-engineered cartilage in a clinical setting requires a noninvasive method to assess the biophysical and biochemical properties of the engineered cartilage. Since articular cartilage is composed of 70-80% water and has dense extracellular matrixes (ECM), it is considered that the condition of the water molecules in the tissue is correlated with its biomechanical property. Therefore, magnetic resonance imaging (MRI) represents a potential approach to assess the biophysical property of the engineered cartilage. In this study, we test the hypothesis that quantitative MRI can be used as a noninvasive assessment method to assess the biophysical property of the engineered cartilage. To reconstruct a model of cartilaginous tissue, chondrocytes harvested from the humeral head of calves were embedded in an agarose gel and cultured in vitro up to 4 weeks. Equilibrium Young's moduli were determined from the stress relaxation tests. After mechanical testing, MRI-derived parameters (longitudinal relaxation time T1, transverse relaxation time T2, and water self-diffusion coefficient D) were measured. The equilibrium Young's modulus of the engineered cartilage showed a tendency to increase with an increase in the culture time, whereas T1 and D decreased. Based on a regression analysis, T1 and D showed a strong correlation with the equilibrium Young's modulus. The results showed that T1 and D values derived from the MRI measurements could be used to noninvasively monitor the biophysical properties of the engineered cartilage.

Purpose: Applying regenerated cartilage in a clinical setting requires noninvasive evaluation to detect the maturity of cartilage tissue. Magnetic resonance (MR) imaging of articular cartilage is well accepted and has been applied clinically in recent years. We attempt to establish a noninvasive method to evaluate the maturity of regenerated cartilage tissue using gadolinium-enhanced MR imaging. Methods: To reconstruct cartilaginous tissue, we embedded articular chondrocytes harvested from bovine humeral head in agarose gel and cultured the cells in vitro up to 4 weeks. The fixed charge density (FCD) of the cartilage was determined using MRI gadolinium exclusion method. The sulfated glycosaminoglycan (sGAG) content was determined by dimethylmethylene blue dye-binding assay. Results: The sGAG content and FCD of the regenerated cartilage increased with duration of culture. In the T1Gd maps, the [Gd-DTPA2-] in the specimen decreased, and the boundary between the sample disk and the bath solution of phosphate buffered saline (PBS) became clearer as time in culture increased. In the linear regression analysis, FCD and sGAG content correlated significantly. Conclusion: Gadolinium-enhanced MR imaging measurements can be useful predictors of the degree of cartilaginous tissue formation.

High b-value diffusion magnetic resonance imaging (MRI) enables us to detect far smaller architectures, by using q-space analysis, than the resolution in conventional MRI. Average displacement, one of the q-space parameters, quantitatively reflects architecture size and is very useful in observing small changes in microstructures in vivo (e.g., neurodegeneration, tumor heterogeneity, and others). Diffusion-weighted imaging (DWI) is performed by a two-dimensional (2D) multislice method; however, due to finite slice thickness and slice gap, there is a partial-volume effect that makes it difficult to detect the net q-space signal. On the other hand, three-dimensional (3D) MRI, having the advantages of very thin slice thickness and no slice gap (contiguous slices), allows volumetric evaluation acquired in a small isotropic voxel, as compared to 2D multislice imaging. Little is known about the isotropic high-resolution 3D DWI application to q-space analysis. In this study, we have developed and implemented a high b-value 3D DWI sequence, applied q-space analysis to study the reliability of high b-value 3D DWI and obtained a microscopic analytical map with isotropic high resolution and less contamination.

This paper discusses an MR Elastography (MRE) method for noninvasive measurement of elasticity and viscosity of biological tissues. In this imaging method, bipolar gradients put into any pulse sequence for MRI. The phase contrast of acquired image is changed by the number of bipolar gradients and their amplitude. From acquired signal (gradient echo and/or spin echo), changing of the phase of magnetized spin is calculated, and analyzed frequency response of applied mechanical vibration from the outside of the biological tissue. The frequency and amplitude of applied mechanical vibration should be changed by elasticity and viscosity of the tissues. The frequency of applied mechanical vibration is from around 100 Hz by mechanical vibrator to high around 1MHz by ultrasound device. In the post processing, elasticity and viscosity is calculated and the phase shift of magnetized spin is analyzed in two or three dimensions. An image is reconstructed as MRE image which is extracted and enhanced elasticity and viscosity of biological tissues.