Search

Abstract Introduction Personal protective equipment is mandatory to protect patients and professionals from diseases, especially in the dental environment. The risk of gloves micro-perforations is imminent when using sharp instruments or cleaning them up during lengthy clinical procedures. Objective This study evaluated the integrity of sterile and non-sterile gloves before clinical use and clarified whether friction with disinfectant solution modifies surface morphology and integrity. Material and method Samples of gloves from four different brands were divided into two groups: (1) Sterile surgical gloves (n=260) and (2) Non-sterile gloves (n=260). They were scissored and placed in Ostby’s arch so that three solutions - distilled water, ethanol 70°, ethanol 96° - were rubbed with a cotton swab. After 30s, 5, 10, and 15 minutes of solution rubbing, samples were verified by a Scanning Electron Microscope. The pore sizes were measured by Image J software. Result Regardless of the brands, all gloves have been significantly affected by solutions and assessment periods. In general, remarkable changes were evident with ethanol 70° and 96°, and higher pore diameters were observed compared to distilled water. Conclusion Rubbing disinfectant solutions increases gloves’ pores sizes, and time negatively influenced its quality.

Abstract Introduction Much advertising in mouthwash is conveyed in all media appealing to the anti-plaque effect and rendering a disservice to the community. Mouth rinses are available over-the-count and differ on their compositions and antimicrobial effectiveness. Objective In this study, we evaluated the antimicrobial activity of 35 widely available mouth rinses against bacterial species involved in initiation of dental biofilm – Streptococcus gordonii, Streptococcus mitis, Streptococcus oralis, Streptococcus salivarius, and Streptococcus sanguinis. Material and method The Minimum Inhibitory Concentration (MIC) and the Minimum Bactericidal Concentration (MBC) of the evaluated mouth rinses were determined according to the Clinical & Laboratory Standards Institute protocols. Data were submitted to Kruskal-Wallis test and Mann-Whitney post hoc (α=0.05). Result About 70% of the mouth rinses achieved high antibacterial activity and 30%, a low antibacterial activity against all the species tested. The most ineffective mouth rinse showed antibacterial activity (MIC) at 1:1 dilution, while the most effective showed activity even at 1:2048 dilution, which may imply prolonged effect in the mouth. About 51% of mouth rinses showed bactericidal activity, and it was verified that cetylpyridinium chloride or chlorhexidine digluconate containing in the formulation were associated with the highest activity. Conclusion Most - but not all - mouth rinses commercially available are effective in inhibiting in vitro initial colonizers of dental surfaces.

A series of experiments were conducted to characterize a novel restorative material. We explored the effect on biological, physical and chemical properties of glass ionomer cement (GIC) adding-the naturally occurring tt-farnesol (900 mM). Two groups were accomplished for all assays: GIC+tt-farnesol and GIC (control). Biological assays: 1) agar diffusion against some cariogenic bacteria; 2) S. mutans biofilm formation and confocal laser scanning microscopy-CLSM. 3) gtfB, gtfC, gtfD, gbpB, vicR, and covR expression; 4) MTT and microscopic morphology. Physical properties assays: 1) roughness; 2) hardness; 3) compressive strength and 4) diametral tensile strength. Chemical assay: Raman spectroscopy. The adding of tt-farnesol to GIC led to larger zones of inhibition (p0.05). Polysaccharides levels increased over time, similarly over groups (p>0.05). Viable and non-viable S. mutans were seen on the specimens' surface by CLSM but their virulence was not modulated by tt-farnesol. The tt-farnesol increased the HaCaT cell viability without impact on compressive and diametral tensile strength and roughness although the hardness was positively affected (p

The use of antimicrobial monomers, linked to the polymer chain of resin composites, is an interesting approach to circumvent the effects of bacteria on the dental and material surfaces. In addition, it can likely reduce the incidence of recurrent caries lesions. The aim of this study was to evaluate the effects of a novel Triclosan Methacrylate (TM) monomer, which was developed and incorporated into an experimental resin composite, on Streptococcus mutans (S. mutans) biofilms, focusing on the analyses of vicR, gtfD, gtfC, covR, and gbpB gene expression, cell viability and biofilm characteristics. The contact time between TM-composite and S. mutans down-regulated the gbpB and covR and up-regulated the gtfC gene expression, reduced cell viability and significantly decreased parameters of the structure and characteristics of S. mutans biofilm virulence. The presence of Triclosan Methacrylate monomer causes harmful effects at molecular and cellular levels in S. mutans, implying a reduction in the virulence of those microorganisms.