Search

Stimulated by the recent advances in computational tools for the simulation of seismic wave propagation problems in realistic geological configurations, this paper presents a 3D physicsbased numerical analysis of near-source ground motion during the MW 6.0 2012 May 29 earthquake in the Po Plain, Northern Italy. To reproduce with sufficient accuracy some of the most peculiar features of the near-source strong-motion records and of the spatial variability of damage distribution, this study required a sequence of investigations, starting from the analysis of a wide set of near-source records, to the calibration of an improved kinematic seismic source model, up to the development of a 3D numerical model of the portion of the Po Plain interested by the earthquake. The latter includes the basin geometry, characterized by sediment thickness sharply varying from few tens of metres to some kilometres. The spatial resolution of the numerical model is suitable to propagate frequencies up to about 1.5 Hz. Numerical simulations were performed using the open-source high-performance code SPEED, based on the Discontinuous Galerkin Spectral Elements method. The 3D numerical model, coupled with the updated slip distribution along the rupturing fault, proved successful to reproduce with good agreement, measured through quantitative goodness-of-fit criteria, the most relevant features of the observed ground motion. These include: (i) the large fault normal velocity peaks at the near-source stations driven by updip directivity effects; (ii) the small-scale variability at short distance from the source, resulting in the out-of-phase motion at stations separated by only 3 km distance; (iii) the propagation of prominent trains of surface waves, especially in the Northern direction; (iv) the map of earthquake-induced ground uplift with maximum values of about 10 cm, in substantial agreement with geodetic measurements and (v) the two-lobed pattern of the peak ground velocity map, well correlated with the distribution of macroseismic intensity. [ABSTRACT FROM AUTHOR]

In the present paper a review of some mathematical models for the ecological evaluation of environmental systems is considered. Moreover a new model, capable to furnish more detailed information at the level of landscape units, is proposed. Numerical tests are then performed for a case study in the province of Viterbo (central Italy). [ABSTRACT FROM AUTHOR]

Abstract: Buildings’ thermal-energetic assessment and the relative proposal of new technical solutions applied to both summer and winter analyses has a strategic role in increasing the year-round performance of buildings. Buildings’ dynamic analysis is by now a well-established procedure to study effective building energy performance given real climate considerations. Then in this work, a concise and effective methodology for analyzing buildings’ thermal performance in a dynamic environment is proposed and applied to different case studies, consisting of single-family residential buildings’ prototypes. This procedure is aimed to define different performance levels by proper non-dimensional indexes named thermal deviation indexes (TDI). These indexes values could express in a concise way buildings’ thermal behavior, different optimization strategies impact, sensitivity analysis results. Buildings’ prototypes representing the case studies are three free-floating houses where the architectural shape role and the sensitivity of different envelope features are analyzed, also supported by experimental results regarding envelope properties measured on existing residential buildings in Italy. The three prototypes are respectively designed to optimize summer or winter energy performance or to represent the typical Italian house before and after energy efficiency regulation is implemented. To better define the important envelope parameters necessary to calibrate the numerical models, experimental activities are conducted. In particular, thermal insulation level and roof reflectance, characterized by means of spectrophotometrical measurements, are measured both in the case of an old traditional Italian building and in the case of a modern building. The results of the dynamic analysis are expressed in terms of TDI values, to define buildings’ thermal performance with respect to the variation of all the considered architectural and envelope’s properties (i.e. architectural layout, mass and insulation, roof reflectance, Solar Heat Gain Coefficients of windows’ glasses, weather data) within a specific climatic context. For validating the proposed method, the obtained TDI results are compared with those obtained from existing procedures. In particular, the TDI values are correlated to an adaptive comfort indicator, for verifying how much the TDI could be effective for evaluating free-running buildings thermal performance during both summer and winter. [Copyright &y& Elsevier]

Abstract: Larderello–Travale is one of the few geothermal systems in the world that is characterized by a reservoir pressure much lower than hydrostatic. This is a consequence of its natural evolution from an initial liquid-dominated to the current steam-dominated system. Beneath a nearly impermeable cover, the geothermal reservoir consists of carbonate-anhydrite formations and, at greater depth, by metamorphic rocks. The shallow reservoir has temperatures in the range of 220–250°C, and pressures of about 20bar at a depth of 1000m, while the deep metamorphic reservoir has temperatures of 300–350°C, and pressures of about 70bar at a depth of 3000m. The 3D numerical code “TOUGH2” has been used to conduct a regional modeling study to investigate the production mechanism of superheated steam, the interactions between the geothermal field and the surrounding deep aquifers, and the field sustainability. All the available geoscientific data collected in about one century of exploration and exploitation have been used to provide the necessary input parameters for the model, which covers an area (4900km2) about 10 times wider than the Larderello–Travale geothermal field (400km2). The numerical model explains the origin of the steam extracted in about one century of exploitation and shows that, at the current level, the production is sustainable at least for the next 100 years. [ABSTRACT FROM AUTHOR]

Abstract: The hydraulic regime-based zonation scheme of the Lagoons of Marano and Grado (Italy) has been derived by means of numerical models. A finite element modelling system has been used to describe the water circulation taking in account different forces such as tide, wind and rivers. The model has been validated by comparing the simulation results against measured water levels, salinity and water temperature data collected in several stations inside the lagoons. The analysis of water circulation, salinity and spatial distribution of passive tracers released at the inlets, led to a physically-based division of the lagoons system into six subbasins. The derived classification scheme is of crucial value for understanding the renewal capacity and pollutants distribution patterns in the lagoon. [Copyright &y& Elsevier]

Abstract: Useful geodynamic distinction of continental collision zones can be based on the degree of rheological coupling of colliding plates. Coupled active collision zones (which can be either retreating or advancing) are characterized by a thick crustal wedge and compressive stresses (i.e. Himalaya and Western Alps), while decoupled end-members (which are always retreating) are defined by a thin crustal wedge and bi-modal distribution of stresses (i.e., compressional in the foreland and extensional in the inner part of the orogen, Northern Apennines). In order to understand physical controls defining these different geodynamic regimes we conducted a 2D numerical study based on finite-differences and marker-in-cell techniques. In our experiments we systematically varied several major parameters responsible for the degree of rheological coupling between plates during collision such as convergence rate, crustal rheology and effective velocity of upward propagation of aqueous fluids and melts in the mantle wedge. Low convergence rates and fluids/melts propagation velocities favor continuous coupling and convergence between the plates. Coupled collision zones are characterized by continuous accretion of the weak upper continental crust resulting in the development of a thick and broad crustal wedge, by hot temperature in the inner parts of the orogen due to radiogenic heating of the thickened crust, by compressive orogenic stresses and appearance of a double seismogenic (brittle) layer involving upper crust and sub-Moho mantle. In contrast high convergence rates and fluid/melt percolation velocities produce efficient weakening of the mantle wedge and of the subduction channel triggering complete decoupling of two plates, mantle wedging into the crustal wedge and retreating style of collision. The evolution of fully decoupled collision zones are characterized by the disruption of the accretionary wedge, formation of an extensional basin in the inner part of the orogen and delamination of the weak portion of the continental crust that is first thrusted toward the foreland and, subsequently, dissected by extensional tectonics. Transition from coupled to decoupled regime occurs always at the early stages of continental collision indicating that insertion of rheologically weak crustal material in the subduction channel is critical for the subsequent evolution of the collision zone. We found good correlations of our numerical results with some of the major collisional orogens. In particular, the decoupled retreating collision regime reproduces what is observed in the Northern Apennines. [Copyright &y& Elsevier]