Search

In this study, numerical simulation of flow and heat transfer of S-CO2 (supercritical CO2) in the inclined upward and downward smooth tubes with an inner diameter of 10 mm and a heating length of 2000 mm at an inclination angle of 45° were conducted. The SST k - ω low Reynolds number turbulence model was used, and the accuracy of the calculation model was verified by the experimental data of S-CO2 flowing upward in the vertical smooth tube. The variation characteristics of the axial and circumferential inner wall temperature T w,i and the convective heat transfer coefficient h were analyzed. The S-CO2 would undergo the phase change from a liquid-like to the vapor-like at the pseudocritical temperature T pc by assuming supercritical pseudo-boiling. Based on this assumption, the reasons for a difference in the wall temperature distribution at the top generatrix during S-CO2 flowing in different directions were studied. By the detailed analysis of the velocity distribution, thermophysical properties distribution, including specific heat capacity at constant pressure cp and thermal conductivity λ , and the turbulent kinetic energy k distribution in the cross-sections of the inclined circular tube, the heat transfer mechanism related to the wall temperature difference at upward and downward was studied. The results showed that the thickness of vapor-like film, axial velocity u , turbulent kinetic energy k , and the thickness of viscosity sub-layer δ y +=5 were the main factors affecting the difference in the wall temperature distribution at the top generatrix in different flow directions.

Biodegradable copolymer-based composites produced from straw fiber (SF) with hydrolyzed soybean protein isolate/urea/formaldehyde (HSPI/U/F) copolymer-based adhesive for biocomposite flowerpots (BFP) application was presented in this work, and molecular structure, morphology, biodegradability and microbial population of the resulting materials were also investigated. FTIR and SEM results indicated that the copolymer resin have been successfully prepared. The prepared BFP showed good biodegradation, and the introduction of HSPI increased the degradation rate of BFP, which was nearly 50% at 24 months. After 30 days of controlled composting, the CO2 release accumulation of BFP could reach 24 g. During the process of BFP degradation, the number of bacteria and fungi on the surface was higher than that of actinomyces, indicating the bacteria and fungi selectively accumulated on the BFP composites surface to accelerate its degradation. At the same time, nitrate ion could also be formed by nitrobacteria, which promoted plant growth. There is no doubt that the obtained biodegradable copolymer possessed great potential for BFP application.

The hydrolytes soy protein isolates (HSPI)-modified urea–formaldehyde (UF) resins were synthesized via copolymerization process. The best bonding strength is 1.50 MPa and improves 51.5% compared with pure UF. In addition, the formaldehyde emission decreased. The effect of (HSPI) on the biodegradable (UF) resins was investigated. Biodegradation was evaluated by composting under controlled conditions in accordance with ISO 14855. The faster degradation rate was obtained when lower hydrolysis degree of HSPI was added into the system. Characterization of the resulting samples was performed by attenuated total reflection Fourier transform infrared spectroscopy, thermo-gravimetric analysis, XRD, scanning electron microscopy, and AFM. The results showed that no evidence of biodegradation was found for UF resins. The UF modified with lower hydrolysis degree of hydrolytes soy protein isolates (HSPI) resulted in a faster degradation rate. The HSPI in the network of modified UF degraded first, which resulted in the ...

The hydrolyzed soy protein isolate (HSPI) was used to partially substitute urea to synthesis modified urea–formaldehyde (UF) adhesives via copolymerization process, in order to reduce the dependency on petroleum-based chemicals and mitigate possible environmental pollution. The soy protein isolate (SPI), HSPI, and modified UF adhesives were characterized by attenuated total reflection Fourier transform infrared spectroscopy, 1H nuclear magnetic resonance (1H NMR), and thermo-gravimetric analysis (TGA). The bonding strength, adhesive properties, biodegradability, and micrographs of the UF and HSPI-modified UF after degradation were also measured. The results show that the SPI native structure is unfolded during the treatment with sodium hydroxide. The thermal stability of HSPI is better than SPI. HSPI can incorporate into the structure of cured UF adhesives with three different feeding methods. And the best bonding strength of modified UF adhesives is 1.31 MPa when HSPI is added at the first step. The form...

To improve the compatibility between rice straw and reinforcing polymers, rice straw (RS) was pretreated by an anaerobic process, and its biogas residues (BR) were acetylated with acetic anhydride (AA) to prepare acetylated biogas residues (ABR). The optimum conditions of acetylation were determined by orthogonal experiments. When acetylation was performed at 140 °C with 10 mL AA/g BR and 0.08 g catalyst/g BR, the maximum weight gain rate (WGR) obtained was 23.7%. Fourier transform infrared (FTIR) analysis showed that many hydroxyl groups were displaced by acetoxy groups. Scanning electron microscopy (SEM) showed that many defects of BR were filled by the acetylation, and an ester layer was formed over the BR surface. However, the lower crystallinity of ABR than the BR and RS affected the mechanical properties of acetylated biogas residue/low density polyethylene (ABR/LDEP) composite. Interestingly, the BR and ABR showed higher onset decomposition temperature, but they exhibited faster decomposition rates because of the lower crystallinity of BR and ABR. Furthermore, the mechanical properties of the RS/LDEP, BR/LDEP, and ABR/LDEP composites were analyzed. Compared with RS/LDEP composites, the BR/LDEP and ABR/LDEP composites showed obviously better tensile and flexural properties. Consequently, rice straw fibers attained excellent compatibility with non-polar polymers.

A composting treatment was employed in an effort to improve the processability of rice husks. Changes in the chemical composition, physical structure, and rheological properties of modified rice husks were analyzed. The results indicated that the average diameter of compost-treated samples was significantly higher than that of the untreated samples because they were able to adhere to each other by the bacterial protein. Scanning electron microscopy images showed that the epidermis became rugged and lumpy because the composition of rice husks (cellulose, hemicellulose, lignin, and pectin) was partially decomposed, an effect confirmed by the chemical composition and FTIR analysis. Thermogravimetric analysis showed that the composted samples had better thermal stability than the untreated ones. Stress-strain curves showed that the treated samples displayed a moderately significant change of slope at about 0 to 10% strain, and they had better mechanical properties than untreated samples. Juxtaposing the rheological properties of both untreated and treated samples determined that the latter had higher apparent viscosity as a result of degradation and bacterial protein effects. All results indicated that the composting treatment changed the physical, chemical, and rheological properties of the rice husks, which are beneficial for its utilization and processability.

The degradation behavior was investigated for eco-composite nursery containers (NCs) prepared with rice husk and cornstarch adhesive modified with urea formaldehyde (UF) as a wet strength agent. The wet shear strength, water absorption capacities, and biological degradation of NCs within soil were also investigated. Quantitative analysis of the thermal degradation behavior of different NC versions was performed by thermo-gravimetric analysis (TGA). The results demonstrated that the introduction of the UF agent accelerated the soil degradation of the NCs matrix to a certain extent. The maximum cumulative mass loss was 51.1% when the UF content of NCs was 8 wt.%. Moreover, the dry strength of the mixed urea formaldehyde-cornstarch adhesive (UCA) was increased by 108.9% compared with cornstarch adhesive (CA). The results of this work indicate the improved biodegradability of the NC eco-composites, which could make them potential sustainable alternatives for conventional plastic pots.

The hydrolyzed soy protein isolate (HSPI) with different hydrolysis degree was applied to modify urea-formaldehyde resins (UF) via copolymerization process. The properties of HSPI were characterized by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) and TGA. The results show that HSPI with different hydrolysis degree is obtained. 1H NMR and ATR-FTIR spectra indicate that HSPI with different hydrolysis degree can incorporate into the structure of cured and uncured UF. The UF modified with higher hydrolysis degree of HSPI possess more stable units and contribute to the lower exothermic peak temperature in DSC curves. The bonding strength of HSPI modified UF increases as the hydrolysis degree of HSPI increases at the hot-press temperature of 120°C and decreases at the hot-press temperature of 150°C. The best bonding strength is 1.53 MPa at the hot-press temperature of 135°C and improved 56.12% compared with UF. In addition, the formaldehyde emission is dramatically reduced. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41469.

A biodegradable planting container made with rice straw and starch adhesives modified by polyvinyl alcohol was studied in this paper. The effect of heat treatment and polyamide resin on the properties of planting containers was investigated. The physical property and biodegradability were characterized by means of hygroscopicity, FTIR, degradability, and the thermogravimetric analysis. The results showed that the dry strength of planting containers increased as a result of both treatments. The wet strength of planting containers increased as a result of heat treatment, while the wet strength of planting containers decreased as a result of polyamide resin. The hygroscopicity of planting containers decreased with heat treatment and polyamide resin. The effect of heat treatment was more obvious than the effect of polyamide resin. It was observed that the peak intensity and position were changed for the 3400 cm-1, 2900 cm-1, 1640 cm -1, 1500 cm-1, 1400 cm-1, and 1050 cm-1 under the treatment of polyamide resin. The weight loss of specimens treated with polyamide resin was larger because of the presence of nitrogen in the resin. The appearance of planting containers showed the heat treatment containers were not easily prone to mildew when used for planting. The thermogravimetric analysis (TGA) showed that heat treatment can improve the thermal stability, while the polyamide resin was shown to promote the degradation of planting containers.