Search

Tillandsia usneoides in epiphytic bromeliads takes up water through the absorptive trichomes on the shoot surface under extreme environmental conditions. Although previous studies revealed the way by which T. usneoides absorbs water and prevents water loss, T. usneoides' water transport is still unclear. We characterized structures of trichome wings of T. usneoides. Wing length-to-thickness ratio with 136 and the trichome interval (d)-to-wing length (l) ratio (d/l) smaller than 1 caused the water film to flatten the wings sequentially, resulting the domino-like water transport. A hinge-like linkage between wing and outer ring cells and the wing size longer than the elastocapillary length (LEC ) brought about this unique reconfiguration, which is the flattening and recovery of wings. T. usneoides transported water rapidly on the surface as the water film propagated on the exterior trichomes with flexible wings and the transport distance at the macroscopic scale grew as tx with x = 0.68 ± 0.04, unlike the conventional scaling of t0.5 . Empirical and theoretical investigations proved our assumption that external water transport with the domino-like effect predominated over internal vascular transport. Biomimetic trichome wings simulated the domino-like water transport, highlighting the important role of flexibility wing arrays.

The biofouling of marine organisms on a surface induces serious economic damage. One of the conventional anti-biofouling strategies is the use of toxic chemicals. In this study, a new eco-friendly oleamide-PDMS copolymer (OPC) is proposed for sustainable anti-biofouling and effective drag reduction. The anti-biofouling characteristics of the OPC are investigated using algal spores and mussels. The proposed OPC is found to inhibit the adhesion of algal spores and mussels. The slippery features of the fabricated OPC surfaces are examined by direct measurement of pressure drops in channel flows. The proposed OPC surface would be utilized in various industrial applications including marine vehicles and biomedical devices.

Water loss can be delayed by trapping it within a polymeric network, i.e. hydrogel. However, the dynamic response of natural materials has not been explained to maintain water levels relatively constant against varying environmental conditions. In this study, patterned polymeric materials formed on plant seeds are observed to provide effective water retention ability against repeated dehydration-rehydration procedures. The perpendicular line pattern (layer-by-layer stack) of the polymer films induces lateral line patterns (surface lines) by a typical wrinkling mechanism, which contributes to the characteristic water interaction. The anisotropic line patterns on the seed surface generate more hydrophilic properties over the isotropic patterns against drying-out. The matric potential (Ψ

BACKGROUND: Iron oxide nanoparticles (IONPs) are excellent candidates for biomedical imaging because of unique characteristics like enhanced colloidal stability and excellent in vivo biocompatibility. Over the last decade, material scientists have developed IONPs with better imaging and enhanced optical absorbance properties by tuning their sizes, shape, phases, and surface characterizations. Since IONPs could be detected with magnetic resonance imaging, various attempts have been made to combine other imaging modalities, thereby creating a high-resolution imaging platform. Composite IONPs (CIONPs) comprising IONP cores with polymeric or inorganic coatings have recently been documented as a promising modality for therapeutic applications. METHODS: In this review, we provide an overview of the recent advances in CIONPs for multimodal imaging and focus on the therapeutic applications of CIONPs. RESULT: CIONPs with phototherapeutics, IONP-based nanoparticles are used for theranostic application via imaging guided photothermal therapy. CONCLUSION: CIONP-based nanoparticles are known for theranostic application, longstanding effects of composite NPs in in vivo systems should also be studied. Once such issues are fixed, multifunctional CIONP-based applications can be extended for theranostics of diverse medical diseases in the future.

Understanding the boiling heat transfer characteristics of nanofluid suspensions containing nanoparticles is one of the challenging issues in the heat transfer research field. The addition of nanoparticles modifies both the surface characteristics and the thermo-physical properties of the suspension, including thermal conductivity, viscosity, and surface tensions. One of the critical features is the stability of nanoparticle suspension, which is strongly related to the formulation method of nanofluids. In this study, to investigate the effect of several formation methods, the pool-boiling bubble behaviors of Al2O3 nanofluid, with varying nanofluid formation methods, were systematically analyzed using an X-ray imaging system. The changes in the wettability of Al2O3 nanofluid suspensions and the variations of boiling bubble characteristics were analyzed to determine the relationship between boiling-bubble behaviors and examine the effects of heating the substrate. Before the heating substrate, the bubble generating ratio was increased by 1.4 times, when the concentration of Nanofluid 3 increased from 0.05 wt% to 1 wt% with adopting the electrostatic stabilization method and high-speed rotating procedure. On the other hand, at the end of heating process, the bubble generating ratio was decreased by 0.78 times for the same concentration change. Once the nanoparticle sedimentation occurred, the trend of wettability and bubble behaviors of nanofluids changed based on the surface modification, regardless of the nanofluid formation method. An increase in the Al2O3 nanofluid concentration results in a deterioration of the heat transfer characteristics, and the formulation method is not related to the boiling heat transfer performance when nanoparticles are deposited.

A numerical procedure for conjugate heat transfer (CHT) analysis based on an immersed boundary (IB) method for large eddy simulation (LES) has been developed. The dynamic subgrid-scale (SGS) stress and heat flux models are implemented in the solver. Since discrepancy between the computational grid and solid-fluid interface generally exists, interpolation of thermal properties at the interface is necessary for the current method. Accordingly, an efficient interpolation scheme using the modified flood-fill algorithm is applied. In order to validate the capability of the developed method, three different CHT cases with turbulent flow were examined: channel flow between heated slabs, thermally-driven flow in a closed cavity, and crossflow around a heated circular cylinder. Compared to cases that just utilized an isothermal or constant-heat-flux boundary condition, when the CHT method was properly implemented, results more closely matched experimental data and existing correlations.

Flexible structures are common in nature and biomimetic applications. A detailed understanding of their interactions with fluid is essential for the optimisation of structural design. The material stiffness has a strong influence on the motion and flows around the body. In this study, the effect of material stiffness on the motion and flow was experimentally investigated. Cylinders with various rotational stiffnesses ranging from 0.610 N·mm to 0.274 N·mm were produced by changing the degree of cross linking of polydimethylsiloxane. The motion and flow near the free end of the cylinders were examined using a high-speed imaging technique, time-resolved particle image velocimetry, and a proper orthogonal decomposition (POD) modal analysis. Consequently, the primary direction of the motion is altered from the inline to cross-flow direction as the stiffness decreases. The cylinder motion is observed to strongly affect the on flows near the free end, and the length and width near the wake are affected by the vibration magnitude of the cylinder along the inline and cross-flow directions. Vortex shedding occurs near the free end when the motion along the cross-flow direction is larger than 0.1D. These flow structures only propagate downstream behind the flexible cylinders having a relatively weak oscillating motion along the inline direction. The present results could be utilised as basic data in the design of bio-inspired cylinder-shaped structural applications, and relevant computational fluid dynamics (CFD) analyses.

Porous structures with various surface wettabilities have been used to handle gas bubbles underwater for practical applications, such as separation, collection, detachment, and migration of the bubbles. Despite the increasing interest in porous structures, the effects of surface wettability on the behaviors of bubbles at porous surfaces have not been fully understood. Herein, we aim to examine the entire dynamics from collision to disappearance of a bubble through a porous membrane with different surface wettabilities. We divided the dynamics into three stages based on the characteristic behaviors such as bubble bouncing and contact line variation. Bubble dynamics is dominated by the existence of air layers covering the membrane surface. Bubbles on hydrophilic and hydrophobic membranes, which do not retain air layer, show the same removal pattern; they bounce on the surfaces, and then penetrate the membranes with pinned and moving contact line in sequence. In contrast, bubbles immediately penetrate the superhydrophobic membrane following the spread along the air layer. The characteristic time for bubble removal depends on the wettability, which affects the membrane permeability. The experimental characterization and theoretical analysis achieved in this work would improve the physical understanding of bubble dynamics on porous membranes and allow a proper design in bubble-related applications.

Reduction of frictional drag exerted on submerged marine vehicles results in considerable economic and environmental benefits. A lubricant-infused surface (LIS) inspired by Nepenthes pitcher was introduced as an emerging surface technology for substantial frictional drag reduction. However, the LIS easily loses its drag-reduction ability because the lubricant is easily depleted by shear stresses of external flow. In this study, a new biomimetic LIS with a unique surface topography is proposed to increase the sustainability of the infused lubricant. This biomimetic LIS has re-entrant shaped cavities in the surface, inspired by the mucus secretion and storage systems of loach, hagfish, and seaweed, whose skin can sustain slippery mucus layers even under continuous exposure to harsh seawater flow conditions. The slippery characteristics and enhanced sustainability of the biomimetic LIS were investigated by directly measurement of the slip length and pressure loss in channel flow over the LIS. The frictional drag reduction efficiency of the biomimetic LIS was measured to be approximately 18% compared with the corresponding no-slip surface. Moreover, the excellent sustainability of the biomimetic LIS was demonstrated by comparing the drag-reduction abilities before and after exposure to a high shear flow. The high durability might be attributed to the re-entrant shaped surface topography of the biomimetic LIS. The present results would provide insights into the design of a robust and sustainable LIS for practical drag reduction applications.

Nanofluid, a liquid suspension containing nanoparticles, has been widely used to enhance heat transfer. However, the heat transfer enhancement mechanism of nanofluids has not been clearly revealed yet. Therefore, understanding the boiling heat transfer of nanofluids is a challenging research issue in the field of heat transfer. When nanoparticles are added into a base fluid, the thermo-physical properties of the fluid and surface characteristics are modified. Those modifications induce changes in the behavior of boiling bubbles. In addition to the size and number of bubbles, the generating rate of boiling bubbles was newly defined to estimate the heat transfer coefficient directly from bubble behaviors according to nanofluid concentration. As the nanofluid concentration increases, both the generating rate of boiling bubbles and the heat transfer coefficient decrease. Wettability and hydrodynamic size were also employed to reason those degradations. Wettability increase leads to the reduction of activated nucleation sites, which reduces the bubble generating rate and heat transfer coefficient with an increase in nanofluid concentration. In this study, the feasibility and usefulness of synchrotron X-ray imaging and a newly defined boiling generating rate for examining boiling heat transfer were verified by observing boiling-bubble behaviors. Moreover, it was also shown that wettability plays an important role in changes of the bubble behaviors and the heat transfer coefficient as surface roughness modification.

Exposure to ultrafine airborne particulate matter (PM1.0) poses a significant risk to human health and well-being. Examining the effect of submicron water droplets on the removal of ultrafine PM is timely and important for mitigating indoor ultrafine PM, which is difficult to filter out from incoming air. In this study, submicron water droplets were made by using a nanoporous membrane and an ultrasonic module of a commercial household ultrasonic humidifier (UH) for effectual ultrafine PM removal. The effect of water droplet size on indoor PM removal was experimentally investigated. Variations in the normalized PM concentration, removal efficiency and deposition constants were evaluated by analyzing the temporal variation in PM concentration inside a test chamber. The measured PM deposition constants were compared with the results of other previous studies. As a result, submicron water droplets of 800 nm in mean diameter were generated by ultrasonic module combined passive nanoporous membrane, and PM1.0 concentration decreased by 30% in the initial 30 min. Compared with micron-sized water droplets, PM1.0 removal efficiency improved by approximately two times higher. Moreover, the substitution of the experimental results into a theoretical model ascertained that PM collection efficiency is increased by approximately 103 levels as the size of water droplets decreases. These results would be utilized in the development and implementation of effective strategies for indoor PM removal.

Plants have a special structure, torus-margo (TM) pit, which comprises a thickened torus at the center encircled by a highly porous margo. It is regarded as a key evolutionary structure to enable stable water transport, minimizing the air spread in the vessels. However, its valve-like dynamics to regulate two-phase flows still remains unclear even at a single pit level. Here, we study the air spreading dynamics using a bioinspired model of this soft pit valve. We divide it into the initial onset and the consecutive air-spreads, and propose the criteria of TM structures as the valve-like function. To delay the onset of air spread, the margo region should be thin and deformable enough to seal the pit aperture with the torus before the air penetration. Even after the onset, the membranes whose maximum pore size is smaller than its thickness can avoid continuous air-spread. The criteria also fit properly into botanical data on the morphologies of TM pits, implying that their valve-like behaviors may alleviate the tradeoff between hydraulic safety and efficiency at the single pit level. Our study would help to understand of the mechanistic pit-level strategy and also can provide insight into fluidic systems to control interfacial phenomena.

With the worsening water scarcity problem, seawater desalination has been receiving gradually increasing attention. Ion adsorptive desalination was introduced as one of the seawater desalination techniques. In our previous study, metal–organic framework (MOF)-incorporated single-network alginate (MOF-Alg(Cu)) beads were used to adsorb ions in seawater. In the present study, MOF-incorporated Cu-based alginate/PVA hydrogel (MOF-Alg(Cu)/PVA) beads were fabricated to enhance the ion adsorption desalination technique. Cu-based MOFs were successfully synthesized in situ on an interpenetrating polymer network (IPN). Given that the IPN hydrogel beads have high stability, the amount of MOF particles extracted during the adsorption of ions is reduced. The fabricated MOF-Alg(Cu)/PVA beads exhibit efficient removal of dissolved ions in artificial seawater and NaCl solution with varied concentrations. The ion adsorption characteristics were evaluated on the basis of adsorption kinetics, adsorption isotherms, and dosage of adsorbent. The repeat cycle tests show that more than half of the ion removal efficiency was maintained after 10 cycle tests. The concentration of artificial seawater was reduced to 1500 ppm by employing MOF-Alg(Cu)/PVA beads through a multistage experiment. Compared with other seawater desalination techniques, the proposed adsorptive desalination technique using MOF-Alg(Cu)/PVA beads will pave the way for developing a new ecofriendly and energy-saving approach.

Deformation of vulnerable stenosis under pulsatile flow conditions and flow-induced stress acting on a fibrous cap are revealed to be proportional to the square of flow rate divided by fibrous cap thickness. Angle variation of jet flow at the throat of vulnerable stenosis is recommended as a diagnostic index for predicting the stress on the cap.

Patterns in materials are not just decoration but also important for function. In view of this, the dynamics of patterning procedures in materials has been investigated as an important developmental procedure. In this study, nanoscale components in a continuum are traced in terms of natural patterning procedures. Externally applied compressive or extensive forces to an elastic thin sheet commonly induce an orientated lateral line pattern. From a nanoscale element point of view, the dynamics of natural arrangements, forming anisotropic patterns in preference to isotropy, still remains unclear. In this study, new developmental procedures for line patterns are suggested by stimuli-responsive viscoelastic nanocomposite network model systems. Forces originating from an internal source without directional orientation generate lines in preference to isotropic patterns. With repeated, non-oriented (or isotropic) and self-modulated strain variations, stress is accumulated to drive anisotropic orientations and further lines. The anisotropic elemental arrangement is justified by the equilibrium between the short-range attraction and long-range repulsion from a bottom-up viewpoint. This study suggests a new material design methodology that is useful for electrical devices, biomedical devices and other patterned soft condensed matter in conjunction with line patterns typically generated in a broad range of viscoelastic materials.

Several arterial diseases are closely related with mechanical properties of the blood vessel and interactions of flow-vessel dynamics such as mean flow velocity, wall shear stress (WSS) and vascular strain. However, there is an opportunity to improve the measurement accuracy of vascular properties and hemodynamics by adopting deep learning-based ultrasound imaging for flow-vessel dynamics (DL-UFV). In this study, the DL-UFV is proposed by devising an integrated neural network for super-resolved localization and vessel wall segmentation, and it is also combined with tissue motion estimation and flow measurement techniques such as speckle image velocimetry and speckle tracking velocimetry for measuring velocity field information of blood flow. Performance of the DL-UFV is verified by comparing with other conventional techniques in tissue-mimicking phantoms. After the performance verification, in vivo feasibility is demonstrated in the murine carotid artery with different pathologies: aging and diabetes mellitus (DM). The mutual comparison of flow-vessel dynamics and histological analyses shows correlations between the immunoreactive region and abnormal flow-vessel dynamics interactions. The DL-UFV improves biases in measurements of velocity, WSS, and strain with up to 4.6-fold, 15.1-fold, and 22.2-fold in the tissue-mimicking phantom, respectively. Mean flow velocities and WSS values of the DM group decrease by 30% and 20% of those of the control group, respectively. Mean flow velocities and WSS values of the aging group (34.11 cm/s and 13.17 dyne/cm2) are slightly smaller than those of the control group (36.22 cm/s and 14.25 dyne/cm2). However, the strain values of the aging and DM groups are much smaller than those of the control group (p < 0.05). This study shows that the DL-UFV performs better than the conventional ultrasound-based flow and strain measurement techniques for measuring vascular stiffness and complicated flow-vessel dynamics. Furthermore, the DL-UFV demonstrates its excellent performance in the analysis of the hemodynamic and hemorheological effects of DM and aging on the flow and vascular characteristics. This work provides useful hemodynamic information, including mean flow velocity, WSS and strain with high-resolution for diagnosing the pathogenesis of arterial diseases. This information can be used for monitoring progression and regression of atherosclerotic diseases in clinical practice.

Estimating pressure variation is essential in membrane systems because it is the primary factor that affects the energy for system operation. Although numerous researches were conducted studies, most previous studies focused on the hydraulic roles of single membrane. In this study, we examined the pressure variations caused by membranes considering the effects of flow rate, number of membranes, and distance between the membranes. Membranes were integrated into a tygon tube and pressure was measured by using a cell pressure probe with the lapse of time. We evaluated theoretical pressure values by using Poiseuille’s law and compared them with the experimental results. The measured pressure values are well matched with the theoretical results. This indicates that the CPP can be used to reliably measure the pressure of fluid flows in a tube. As a result, when the flow rate increases 200 times, the increasing rate (slope) of pressure increases 25.9 times and the hydraulic resistance increases by 27.5% as the number n increases 1 to 3. In addition, as the distance between two membranes increases more than 6 cm, the flow pressure of the flow passing the two membranes approaches the value for passing a single membrane. This study will be helpful to understand the pressure variations in various porous fluidic systems composed of membranes.

In this study, the spontaneous ion concentration polarization phenomenon induced by pressure via a cation-selective membrane was theoretically and experimentally investigated. Unlike conventional electrokinetic ion concentration polarization, which uses electric current as a driving flux of cations through the membrane, advection caused by pressure is used as a transmembrane driving flux of cations to spontaneously and stably form an ion depletion zone in the present ion concentration polarization technique. The ion depletion zone produced in a simple experimental setup was used to filter electrolyte and preconcentrate ions and microparticles. Different from the general assumption of the negligible thickness of the electric double layer in microchannels, the low concentration in the ion depletion zone considerably increased the length of the electric double layer. This enhanced the formation of the ion depletion zone. The present results can improve the understanding on ion transport in the ion concentration polarization system and can be utilized to develop a portable water desalination device for rural/remote areas and for preconcentrating biomolecules.

Recently, the multi-needle drug injection has been adopted to overcome the shortcomes of conventional single-needle injection, enhancing the efficiency of drug delivery. However, the effect of needle array on the efficacy of drug delivery has not been fully elucidated. In this study, the interactions of drug analogous solution injected from a pair of needles were analyzed to examine the design criteria of effective multi-needle devices for drug delivery. Temporal and spatial variations of relative contents of the solution in the tissues were compared according to the distance between two adjacent needles (DN). As the DN increases from 5 to 20 D, where D is the needle diameter, the solution from each needle encounters 3.5 times faster, and 4.22 times more solution was accumulated. At the same time, the effective spreading area was continuously increased from 54.2 to 177.8 mm2 and RCS gradient decreases from 0.087 to 0.037, due to the overlapping effect of the spreading solution from neighboring needles. Finally, based on the experimental results, an optimal design criterion of needle array for effective drug delivery was proposed. The present results would be helpful in the design of multi-needle injection devices and eventually offer advantage to patients with effective drug delivery.

A digital stereo-holographic microscopy (DsHM) with two viewing angles is proposed to measure 3D information of microscale particles. This approach includes two volumetric recordings and numerical reconstruction, and it involves the combination of separately reconstructed holograms. The 3D positional information of a particle was determined by searching the center of the overlapped reconstructed volume. After confirming the proposed technique using static spherical particles, the 3D information of moving particles suspended in a Hagen–Poiseiulle flow was successfully obtained. Moreover, the 3D information of nonspherical particles, including ellipsoidal particles and red blood cells, were measured using the proposed technique. In addition to 3D positional information, the orientation and shape of the test samples were obtained from the plane images by slicing the overlapped volume perpendicular to the directions of the image recordings. This DsHM technique will be useful in analyzing the 3D dynamic behavior of various nonspherical particles, which cannot be measured by conventional digital holographic microscopy.

Analogous to the morphological and functional features of cactus root, a novel cactus root-inspired material (CRIM) was fabricated by integrating cellulose fibers, microparticles, and agarose-based cryogels. Without undergoing sophisticated chemical synthesis or surface modification, the CRIM exhibited efficient water absorption and retention ability with high structural stability. 82% of the total water absorption capacity was recovered within 1 min, with a swelling rate nearly 930-fold faster than the evaporation rate, while only about 17% of the length extension occurred. Given that efficient water absorption and storage without physical change is crucial to the design and fabrication of water management devices, the CRIM is a promising material for various applications, including cosmetics or healthcare products, functional fabrics, and drug delivery devices.

The goal of this study was to analyze the bearing properties of the differently oriented glulam using digital image correlation (DIC). Six differently oriented specimens associated with three anatomical directions including longitudinal (L), radial (R), and tangential (T), and 12-mm drift pins were used to analyze the bearing properties, including yield load and bearing strength. The highest bearing strength of 22.57 MPa from RL was found, whereas the lowest bearing strength of 6.47 MPa from LR was found. Different strain distributions were observed from the differently oriented bearing specimens using DIC. Different failure ratios of the differently oriented specimens were highly related to the strain distributions. Although the bearing properties were found to be different between the differently oriented specimens, for the connection design aspect, the bearing properties of glulam could be grouped as RL and TL specimens, RT and TR specimens, and LR and LT specimens.

The aim of this study was to develop a stochastic model for predicting the bending strength distribution of glued-laminated timber (GLT). The developed model required the localized modulus of elasticity (MOE) and tensile strengths of laminae as input properties. The tensile strength was estimated using a regression model based on the localized MOEs and knot area ratios (KAR) which were experimentally measured for lamina grades samples. The localized MOE was obtained using a machine stress-rated grader, and the localized KAR was determined using an image-processing system. The bending strength distributions in four types of GLTs were simulated using the developed GLT beam model; these four types included: (1) GLT beams without finger joints; (2) GLT beams with finger joints; (3) GLT beams with different lamina sizes; and (4) GLT beams with different combinations of lamina grades. The simulated bending strength distributions were compared with actual test data of 2.4 and 4.8 m-long GLTs. The Kolmogorov–Smirnov goodness-of-fit tests showed that all of the simulated bending strength distributions agreed well with the test data. Especially, good agreement was shown in the fifth percentile point estimate of bending strength with the difference of approximately 1%.

This study investigated the low-temperature fracture behavior of an 80-mm-thick low-carbon steel plate welded by submerged arc. The relationship between impact absorbed energy and ductility–brittle transition temperature (DBTT) based on the microstructures was evaluated through quantitative analysis on grain size and complex constituent phases using advanced EBSD technique. The microstructure formed differently depending on the heat affections, which determined fracture properties in a low-temperature environment. Among the various microstructures of the heat-affected zone (HAZ), acicular ferrite has the greatest resistance to low-temperature impact due to its fine interlocking formation and its high-angle grain boundaries.

Marine biofouling of ship hulls and ocean structures causes enormous economic losses due to increased frictional drag. Thus, efforts have been exerted worldwide to eliminate biofouling. In addition, a strong demand exists for the development of a cost-effective and eco-friendly anti-biofouling coating technology. Thus, erucamide-polydimethylsiloxane (EP) coating is proposed in this study. EP exhibits a hydrophobic surface as the erucamide content and drag reduction effect increase. In this study, the drag reduction effect of the EP 2.5 is better than that of glass and polydimethylsiloxane (PDMS) surfaces. Moreover, the proposed EP coatings are observed to prevent the biofouling induced by bacteria (E. coli) and brown algae (Cladosiphon sp.). In addition, through a marine field test, the anti-biofouling effect of the EP surface is found to be better than the previously studied oleamide-PDMS (OP) surface. In the marine field test, the EP 2.5 demonstrates superior anti-biofouling performance for 5.5 months under real marine environment. The proposed eco-friendly EP coating method could be applicable to marine vehicles that require effective drag reduction and anti-biofouling properties.

Air plastron in a superhydrophobic (SHPo) surface works as a lubricant that induces drag reduction on the surface. By air plastron, air is trapped between structures of the SHPo surface. However, air plastron is easily depleted by static water pressure or external flow conditions. Various nanostructures have been introduced to enhance the air stability of SHPo surfaces. In this study, the effects of such nanostructure on the air stability were experimentally investigated under high water pressure and flow conditions. Polyvinyl chloride solution was employed to form the nanostructure on the ridged SHPo surface. The critical pressure for the depletion of air plastron is 70% higher on SHPo surfaces introduced with the nanostructure than on surfaces without the nanostructure. Pressure drops (ΔP) in rectangular channels with the SHPo surface on the bottom side were measured to quantify the air stability under a flow condition. ΔP gradually decreases as the air plastron disappears on both SHPo surfaces. The hierarchical ridged surfaces with the nanostructure showed better air stability under static and flow conditions compared with the simple ridged surfaces without the nanostructure. The present results are helpful to understand the effects of the nanostructure on the air stability and its drag reduction mechanism.

Anti-biofouling surfaces are very important owing to their significant roles in microfluidic devices, biosensors and biomedical devices. However, traditional anti-biofouling surfaces could contaminate the environment. Thus, the development of environment-friendly coatings is an essential undertaking in efforts to resolve the problems associated with conventional anti-biofouling surfaces. Herein, a novel strategy inspired by the slippery surface of loach skin is proposed for the rational design of anti-biofouling surfaces. In this strategy, hydrophilic biopolymers, including chitosan, carboxymethyl cellulose, mPEG-amine (MW, 10,000 Da) and alginate, are grafted on a porous polycaprolactone (PCL) membrane. The porous PCL surface is a biomimetic surface inspired by the skin surface of a loach that secretes mucus. Previously developed antifouling surfaces were often toxic or the coating substances were easily released to the outside, and their drag reduction effects were not examined. The developed coating surface is not toxic and the coating material is not depleted to the outside. The resultant covalent biopolymer-coated surfaces (BCSs) exhibit excellent hydrophilic property and drag reduction effect in water. Especially, the additional coating of mPEG-amine on the alginate-coated surface exhibits the best drag reduction performance. In addition, the BCSs show superior anti-biofouling performance by resisting the adhesion of bacteria (Escherichia coli and Maribacter dokdonensis) and NIH3T3 fibroblasts. The proposed covalent biopolymer coatings could be potentially utilised as eco-friendly surfaces for drag reduction and anti-biofouling.

In this study, we investigated the dynamic functions of the tip region of the butterfly proboscis through which liquid is sucked during liquid feeding. The microstructures and flow patterns in the tip region of the proboscis were in vivo analyzed. The tip region can be divided into two functional sections: namely adhesion and suction sections. The liquid adheres to the adhesion section during liquid suction. Although the tip region has numerous slits connected to food canal of the proboscis, liquid is mainly sucked through the suction section, which section is submerged in the fluid pulled by the adhesion section and then successfully imbibes liquid. To check the dynamic functions of the tip region, we fabricated a suction tip model having adhesion and suction parts. The in vitro model experiments show that the hydrophilicity of the adhesion part and the existence of the suction inlet improve the liquid uptake driven by a suction pump. This study may provide insights for the biomimetic design of nectar-feeding butterflies.

In this study, the bending behavior of cross-laminated timber (CLT) connected by nails were investigated. Especially, the load-carrying capacity of the nail-jointed CLT under out-of-plane bending was predicted by the lateral resistance of the used nails. Three-layer nail-jointed CLT specimens and a nail connection were manufac-tured by 30 mm (thickness) × 100 mm (width) domestic species (Pinus koraiensis) laminas and o3.15 × 82 mm nails using a nail-gun. Shear test for evaluating the nail lateral resistance and bending test for evaluating the load-carrying capacity of the nail-jointed CLT under out-of-plane bending were carried out. As a result, two lateral resistance of the used nail, the 5% fastener offset value and the maximum value, were 913 N and 1,534 N, respectively. The predicted load-carrying capacity of the nail-jointed CLT by the 5% offset nail lateral resist-ance was similar to the yield points on the actual load-displacement curve of the nail-jointed CLT specimens. Meanwhile, the nail-jointed CLT specimens were not failed until the tension failure of the bottom laminas oc-curred beyond the maximum lateral resistance of the nails. Thus, the measured maximum load carrying capacities of the nail-jointed CLT specimens, approximately 12,865 N, were higher than the predicted values, 7,986 N, by the maximum nail lateral resistance. This indicates that the predicted load-carrying capacity can be used for designing a structural unit such as floor, wall and roof able to support vertical loads in a viewpoint of pre-dicting the actual capacities more safely.

The improvement of the fuel efficiency of heavy vehicles has received considerable attention. Thus, various flow-control devices have been implemented to reduce aerodynamic drag exerting on heavy vehicles. In this study, we proposed noble boat tail with lower inclined air deflector (LIAD), as a passive flow-control device on attached at the rear end of heavy vehicles. The aerodynamic performance of the modified boat tail with LIAD is experimentally examined by measuring the drag force, side force exerting on a real-shaped heavy vehicle model at various yawing angles. As a result, the maximum drag reduction effect of the boat tail with LIAD (θ = 45°) is about 9.02% compared to the result without the boat tail, although the length of the bottom tail is half of that of four-way boat tail. Furthermore, particle image velocimetry velocity field measurements were conducted to investigate the modified flow structure are by the attachment of various boat tails. Consequently, the LIAD effectively suppresses the formation of large-scale recirculating zone in the wake behind the rear body of the vehicle, as an effective guide of the underbody flow.

The aim of this study was to investigate whether making incising for injecting alkaline copper quaternary (ACQ) into wood extends the wood’s biodeterioration resistance. The biodeterioration resistance was checked by comparing long-term residual ACQ in wood with a toxic threshold to fungi. The residual ACQ in wood was estimated by leaching ratios and a long-term emission model which was derived by leaching tests of full-sized ACQ treated wood. The initial retention and the amount of ACQ leached of incised specimens were higher than those of non-incised specimens. However, the initial retention had a larger impact on leaching ratio than amount of ACQ leached. As a result, the leaching ratios of incised specimens were lower than those of non-incised specimens. The results indicate that incised wood can be expected to have the biodeterioration resistance for a longer period of time than non-incised wood.

Undulatory topographical waves of bioinspired dynamic surfaces effectively prevent surface fouling., Diverse bioinspired antifouling strategies have demonstrated effective fouling-resistant properties with good biocompatibility, sustainability, and long-term activity. However, previous studies on bioinspired antifouling materials have mainly focused on material aspects or static architectures of nature without serious consideration of kinetic topographies or dynamic motion. Here, we propose a magnetically responsive multilayered composite that can generate coordinated, undulatory topographical waves with controlled length and time scales as a new class of dynamic antifouling materials. The undulatory surface waves of the dynamic composite induce local and global vortices near the material surface and thereby sweep away foulants from the surface, fundamentally inhibiting their initial attachment. As a result, the dynamic composite material with undulating topographical waves provides an effective means for efficient suppression of biofilm formation without surface modification with chemical moieties or nanoscale architectures.

Plants transport water against the risk of cavitation inside xylem vessels, called ``embolism.'' As one of their hydraulic strategies, pit membranes composed of cellulose fibers have been known as safety valves that prevent the spreading of embolism towards adjacent xylem vessels. However, detailed observation of embolism spreading through a pit membrane is still lacking. Here, we hypothesized that the pit membranes normally remain to be wetted in xylem vessels and noticed in particular the hydraulic role of water film on air spreading that has been overlooked previously. For the hydrodynamic study of the embolism spreading through a wetted pit membrane, we investigated the penetration and spreading dynamics of air plugs through the wetted cellulose membrane in a channel flow. Air spreading exhibits two types of dynamics: continuous and discrete spreading. We elucidated the correlation of dynamic characteristics of air flow and pressure variations according to membrane thickness. Our study speculates that the thickness of pit membranes affects the behaviors of water film captured by cellulose fibers, and it is a crucial criterion for the reversible gating of further spreading of embolism throughout xylem networks.

The removal of particulate matter (PM) is an important issue in public health and the global atmospheric environment. Various PM removal methods have been suggested to effectively remove PM particles. However, the effects of various factors on PM deposition are not completely clear. We quantitatively investigated the effects of flow and humidity difference in a closed chamber on PM deposition. To elucidate the parameters affecting the deposition of PM particles, PM removal efficiency and deposition constant were examined at different flow rates, flow directions, and relative humidity (RH) inside the closed system. The highest PM deposition rate was achieved under humid condition with the upward direction flow at a fan speed of RPM = 150. Mean velocity fields inside the test chamber were obtained by a particle image velocimetry (PIV) technique to quantitatively examine the effect of flow conditions on the PM deposition. The flow structure and RH inside the closed chamber have significant influence on PM deposition.

Spontaneous filtration without a power supply was investigated using highly charged precursor mixtures instead of recognized microfluidic desalination techniques. The proposed filtration method consisted of a main channel (depth: 1 mm) and shallow channels (depth: 400 μm) in which the precursor mixture was injected. The filtration performance of the proposed device was evaluated by injecting a fluorescent dye that moved toward the centerline of the main channel. The respective rejection rates of CaCl2, NaCl, CaSO4, and Na2SO4 were 3.16%, 30.13%, 43.74%, and 36.32%, respectively. This trend can be explained by the mechanism of Donnan exclusion theory. The focusing of charged species toward the centerline of the main channel was caused by highly charged surfaces. The proposed filtration method exhibited a migration of charged microparticles toward a certain direction. This particle migration behavior was consistent with the simulation data. These results suggested that the proposed filtration method had strong potential for desalinating brackish water or salty surface water without an external power supply.

Porous structures, such as perforation plates and pit membranes, have attracted considerable attention due to their hydraulic regulation of water flow through vascular plant networks. However, limited information is available regarding the hydraulic functions of such structures during water-refilling and embolism repair because of difficulties in simultaneous in vivo measurements of refilling flow and pressure variations in xylem vessels. In this study, we developed a xylem-inspired microchannel with a porous mesh for systematic investigation of the hydraulic contribution of perforation plates on water-refilling. In particular, the “stop-and-acceleration” phenomenon of the water meniscus at the porous mesh structure was carefully examined in macroscopic and microscopic views. This distinctive phenomenon usually occurs in the xylem vessels of vascular plants during embolism repair. Based on the experimental results, we established a theoretical model of the flow characteristics and pressure variations around the porous structure inside the microchannel. Perforation plates could be speculated to be a pressure-modulated flow controller that facilitates embolism recovery. Furthermore, the proposed xylem-inspired channel can be used to investigate the hydraulic functions of porous structures for water management in plants.

Sustainable green energy technologies have paid much attention to the development of a solar-driven seawater desalination technique due to its ecofriendly and efficient desalination performance. We propose a novel hybrid hydrogel consisting of conducting polymer of polypyrrole (PPy) and polyvalent cations crosslinked alginate (Alg) with strong repulsive force for simultaneous seawater desalination and electricity generation. The strong repulsive force of polyvalent cations crosslinked with Alg selectively rejects salt cations by inducing reverse salinity gradient against the rapid evaporation-induced salt accumulation on the upper surface of the solar evaporator. The proposed PPy–incorporated Alg (PPy/Alg) hydrogel exhibits an evaporation rate of 1.15 kg h−1 m−2 with a conversion efficiency of 54.12% under 1 sun solar irradiation. In addition, this hydrogel has an excellent crystalline antifouling property, and can be easily scaled-up with maintaining solar desalination performance. Depending on the compositions of PPy and Alg, the spontaneous electricity generation is largely affected by the balance between the decreased salinity gradient by the accumulation of salt cations and the increased salinity gradient by the strong repulsive force. The present results would pave a novel way for the development of sustainable electricity generation in combination with solar-driven seawater desalination by a facile methodology and energy-friendly process.

Plants are considered as a possible modality to reduce particulate matter (PM) particles from ambient air in an ecofriendly manner. A new precise monitoring technique that can explore interactions between individual PM particles and a leaf surface is necessary to understand the underlying mechanisms of PM removal of plant leaves. In this study, a digital in-line holographic microscopy (DIHM) was employed to experimentally investigate the settling motions of PM particles over the leaf surface. The in-plane positions and sizes of opaque PMs with irregular shapes were obtained from the projection images of numerically reconstructed holographic images. The depth positions of PMs were determined by using proper selection of an autofocusing criterion with automatic segmentation method. The edge of a hairy Perilla frutescens leaf was detected by adopting several digital imaging processing techniques. The DIHM technique was applied in this study to accurately detect 3D settling trajectories of PMs with velocity information of PMs in the midair and near leaf surface, simultaneously.

The uptake of heavy metals by plants has been receiving much attention for crop contamination and phytoremediation. We employed synchrotron X-ray fluorescence (XRF) spectroscopy for an in-vivo analysis of heavy-metal uptake through a strand of maize root. A focused X-ray beam of 2.5 × 2.5 μm2 in physical dimensions was scanned along horizontal lines of the maize root at intervals of 3 μm at the 4B X-ray micro-diffraction beamline of the Pohang Accelerator Laboratory (PAL). Time-resolved mapping of the fluorescence intensities from multiple metallic elements in the root tissues provided information about the radial distributions of heavy-metal elements and their temporal variations. The concentrated core stream of heavy-metal elements spread radially up to roughly 500 μm, corresponding to 40 % of the root diameter. The absorption characteristics of three heavy metals, Cr, Mn and Ni, and their physiological features were analyzed. The absolute concentrations and the contents of the heavy-metal elements in the tested maize roots were quantitatively evaluated by using the calibration curve obtained from reference samples with preset concentrations. The uptake quantities of the tested heavy-metal elements are noticeably different, although their molecular weights are similar. This study should be helpful for understanding plant physiology related with heavy-metal uptake.

Purpose To investigate the details of the flow structure of a plug-like jet that had a vortex ring in pulsatile stenotic phantoms using 4D flow MRI. Method Pulsatile Newtonian flows in two stenotic phantoms with 50% and 75% reductions in area were scanned by 4D flow MRI. Blood analog working fluid was circulated via the stenotic phantom using a pulsatile pump at a constant pulsating frequency of 1 Hz. The velocity and vorticity fields of the plug-like jet with a vortex ring were quantitatively analyzed in the spatial and temporal domains. Results Pulsatile stenotic flow showed a plug-like jet at the specific stenotic degree of 50% in our pulsatile waveform design. This plug-like jet was found at the decelerating period in the post-stenotic region of 26.4 mm (1.2 D). It revealed a vortex ring structure with vorticity strength in the range of ± 100 s − 1 . Conclusion We observed a plug-like jet with a vortex ring in pulsatile stenotic flow by in vitro visualization using 4D flow MRI. In this plug-like jet, the local fastest flow region occurred at the post-systole phase in the post-stenotic region, which was distinguishable from a typical stenotic jet flow at systole phase.

We have previously reported the discovery of a novel fibrous structure (NFS) consisting of unidirectionally arranged collagen fibers in the spinal pia mater. Due to its unique structure, it was easily detected using polarized light microscopy. In the current study, we describe the discovery of a similar NFS in the brain meninges of rats by using polarized light microscopy. This NFS is located beneath the superior sagittal sinus. Initially, we systemically analyzed the polarization properties of the NFS. The change in the light intensity of the NFS, with respect to the polarization angle, was eight times greater than that of blood vessels, showing that the collagen fibers are oriented in a particular direction with almost perfect parallelism (0.99). The orientation angle of the polarization ellipse confirmed the orientation of the collagen fibers in the NFS. Histological studies further confirmed that the unidirectionally arranged collagen fibers were responsible for this distinct polarization property. Surprisingly, X-ray microtomography and 3D confocal imaging revealed that the NFS contains within it a duct structure, a putative primo vessel. In conclusion, we report a NFS in the brain meninges, detected by using polarized light microscopy, that provides space for a putative primo vessel, not a blood vessel.

The relief of residual stress of electrodeposited nickel by using amine as an additive in sulfamate electrolyte is reported. It is shown that the amine additive effectively changed tensile stress into compression stress, even in the very low concentration range in the order of 10−3 M. The changes in microstructure and microhardness by the amine addition are also presented.

Liquid-infused surfaces are a promising passive technique for frictional drag reduction. However, their practical application is limited by the easy depletion of the lubricant infused in the surface by external forces. Miyeok contains mucus on its surface, which induces a sustainable slippery surface under flow conditions. In this study, the effect of the surface morphological structures of miyeok on slippery characteristics was examined. The surface of miyeok has bump-like microstructures and tiny pores of mucilage gland cells with a re-entrant inlet configuration. A replica model of the miyeok surface was fabricated by adopting a molding process using polydimethylsiloxane. The miyeok replica model was dipped into a silicone oil solution to obtain a slippery surface property. The surface structures of fresh miyeok and the replica were checked by comparing their scanning electron microscopy images. A replica of a kelp surface was also fabricated by employing the same method. The heights of the surface microstructures of the miyeok replica were more uniform than those of the kelp replica. The sustainable drag reduction effect of the replica models’ surfaces was assessed by a sessile drop method. The liquid-infused miyeok replica surface (LIMRS) showed better sustainability than other surfaces. The slippery properties of the LIMRS were examined by measuring slip length and pressure drop. The drag reduction rates measured by the two methods were approximately 24% and 19%. The present results would be helpful for understanding the effects of the surface structure of natural miyeok on sustainable drag reduction and developing a biomimetic sustainable drag-reducing surface.

Solar steam generation is a promising technology for harvesting solar energy to purify seawater and wastewater. State-of-the-art technologies have struggled to achieve sufficient solar evaporation rate and antifouling property simultaneously. In addition, the antifouling strategies based on flow dynamics need to be established to develop more efficient membrane designs. Here we propose a new superhydrophilic thermally-insulated macroporous membrane (STIMM) composed of carbonized sucrose and polydimethylsiloxane as an efficient solar evaporator. The converted solar energy is fully utilized for evaporation by the aid of the coupled effects of superhydrophilicity and heat localization. STIMM achieves a high evaporation rate of 2.045 kg/m2/h even at its macropore size under 1 sun irradiation, overcoming the previous trend limit. The macropores of STIMM enable self-cleaning with a 93.1% salt rejection rate. The high evaporation rate and geometrical traits of STIMM generate strong convective flows to dynamically reject salt. The solar desalination system based on STIMM stably produces a practically high amount of purified water with a production rate of 24.9–30.6 L/m2/day. Our proposed STIMM demonstrates a new paradigm for facile desalination systems that are low cost, energy efficient, and self-cleaning under natural environmental condition.

The effective removal of indoor particulate matter (PM) has received considerable attention due to the harmful effects of airborne PM on human health. Although various techniques have been introduced to remove indoor PM, no impeccable method has been established. In this study, we proposed the use of microscale water droplets produced by the ultrasonic module of a commercial household ultrasonic humidifier (UH) for effective PM removal. Water droplet size was regulated using micropinholes. The effect of water microdroplet size on the removal of indoor PM was experimentally investigated. Normalized PM concentration, PM removal efficiency and PM deposition constant were assessed by analyzing the measured temporal variations in PM concentration inside a test chamber. The PM deposition constants measured in this study were compared with those of other previous studies. Deposition events were quantitatively visualized by using a high-speed camera attached with a long-distance microscope. The increase in the deposition rate of surface area and the PM collection ratio were analyzed using digital image processing to examine the interactions between PM particles and water microdroplets with different droplet sizes. As a result, the removal efficiency of PM2.5 particles reaches up to 56.2% when water droplets of d = 2 μ m are used. The PM10 removal efficiency is also increased by 73.9% within the initial 30 min. The deposition constant for the smallest water droplets of d = 2 μ m is drastically increased. In addition, the increasing rate of the deposition surface area is exponentially increased, as the size of water droplets decreases. The small microscale water droplets generated by a commercial UH attached with a micropinhole are found to be effective for the removal of indoor PM.

Airborne particulate matter (PM) has emerged as an important global environmental and social issue due to its harmful health effects. Various techniques have been introduced to remove indoor PM. However, an effective and sustainable method has not been established yet because of complex mechanisms and various factors. Here, we propose the use of water microdroplets generated by a MHz-frequency ultrasound, and experimentally examine the effects of the generated microdroplets on PM removal. The PM removal efficiency and PM deposition constant are analyzed by measuring the temporal variation of PM concentration. The measured experimental results are compared with analytical deposition constants. Two collection efficiencies derived in previous studies are employed to substitute a mathematical model used for determining the analytical deposition constants. In addition, the mean diameter and the moving velocity of the microdroplets are experimentally measured via a digital holographic microscopy and particle image velocimetry generated by a MHz-frequency atomizer. The present results demonstrate that water microdroplets generated by the atomizer can be effectively used to remove PM.

Water transport in the root and soil interface has been investigated to reveal water uptake phenomena through roots. However, the mucilage-filled pore space used for water uptake has not yet been fully understood because it is difficult to analyze the multi-phase flow in an opaque porous media. In this study, the variations of water content (WC) in the region near the root of a Spathiphyllum wallisii were systematically investigated using an X-ray imaging system. Based on the spatial variations of WC around the root, the water transport phenomena in the mucilage-filled pore space were observed. To explain the water transport phenomena through the porous media around the root, the spatial variations of WC along the vertical direction were also analyzed. The present X-ray imaging technique would be helpful to understand water transport near roots of a plant.