Search

To suppress the high frequency combustion instability of rocket engines, quasi-direct current (quasi-DC) discharge plasma is considered in combination with special arrangements in a rocket engine combustor. After establishing an internal reacting flow field model of a rocket combustor and a phenomenological plasma model, the influence of quasi-DC discharge plasma on high frequency combustion instability is numerically investigated. The results show that the characteristics of the high frequency combustion instability in the combustor are captured very well through the simulation. Based on the DES turbulence model, a positive feedback process is clearly observed for the self-excited combustion instability. The mean temperature and pressure of the combustor are not sensitive to the occurrence of quasi-DC discharge plasma. The pressure histories of the combustor and their characteristic oscillating frequencies are not affected by the plasma when only one actuator is in operation. However, the oscillating amplitudes of the pressure are reduced within a certain time when several actuators are in operation. The heat release becomes more diffusive and more eddies form around the injector faceplate with an increasing number of plasma filaments. Mainly through the reduction of local heat release, the plasma is capable of affecting the high frequency combustion instability in the combustor. To better control high frequency combustion instability, the optimal arrangement is a double-plasma filaments with symmetrical actuators.

There is a lack of understanding of the spray characteristics of gas-centered swirl coaxial (GCSC) injectors during self-pulsation occurs. Therefore, the self-pulsation of a GCSC injector was investigated experimentally in this study. Experiments were conducted at atmospheric pressure with filtered water and dried air supplied through a propellant feed system. A back-lighting high-speed photography technique was used to capture unsteady spray features. A laser-based particle size analyzer (LPSA) was used to measure the size of the droplets in the spray. The effects of recess and gas-liquid ratio on spray self-pulsation were analyzed. It was found that the recess of the injector strongly determines the spray pattern. When spray self-pulsation occurs without recess, both the center and periphery of the spray oscillate. With an increase in the mass flow rate of the gas, the boundary between the center and the periphery of the spray becomes more noticeable. Meanwhile, small droplets in the spray center oscillate, with the periphery of the spray being characterized by a periodic “shoulder.” Under the same operating conditions but with a small recess (2 mm), the spray adheres to the injector faceplate. With a larger recess (7 mm), when spray self-pulsation occurs, the spray periodically forms “shoulder” and “neck,” similar to the behavior of self-pulsation in a liquid-centered coaxial injector. Therefore, it can be concluded that spray self-pulsation enhances atomization at the center of the spray to a certain extent. However, atomization becomes worse in the periphery with an oscillating spray.

The numerical calculation of three-dimensional unsteady combustion for the combustion chamber of LOX/kerosene high pressure staged combustion rocket engine was carried out. By changing the offset ratio of oxygen mass flow rate in the edge area of the injector face, computational studies were conducted to investigate the effects of non-uniform distribution of oxidizer flow on combustion instability for a liquid-propellant rocket engine. The calculation results show that the offset ratio of oxygen mass flow rate changes the distribution of heat release in the combustion chamber. Within a certain range of offset ratio, the non-uniform distribution degree of oxidizer flow enhances the coupling between the pressure and heat release. As a result, it leads to an increase in the pressure oscillation amplitude in the combustion chamber. However, if the offset ratio is too large, the oxygen-fuel ratio will be too small in some regions, which will reduce coupling between the pressure and heat release and increase the damping of combustion instability.

Non-equilibrium plasma has significant chemical kinetic effect and aerodynamic effect, both of which play an important role in the plasma-assisted combustion. In this paper, the numerical study on plasma-assisted combustion in gaseous methane rocket engine is carried out to investigate the impact of kinetic effect on its combustion performance. There are three schemes of plasma excitation via oxygen, methane and both of them in the numerical simulation model. The variations of combustion chamber temperature, pressure, species concentration and special impulse with different dissociation degrees are analysed in three discharge schemes. The results show that non-equilibrium plasma can effectively increase methane burning rate, shorten unburnt area upstream of combustion chamber, and increase the width of combustion zone in shear layer upstream of combustion chamber. And this phenomenon becomes more obvious with the increase of excitation intensity. In addition, more methane and oxygen are added to the combustion process under plasma actuation, and the mole fraction of water is increased in combustion products. The specific impulse of engine is also increased under plasma actuation. At the same degree of dissociation, the combustion-supporting effect of simultaneous discharge of oxygen and methane is significantly greater than that of any component discharge. And in the condition of single component discharge, the combustion-supporting effect of methane is better than that of oxygen.

[Abstract] The present study has been focused on measuring the combustion process of gelled propellant in high-pressure oxidant environment. The research object consisted of gel droplet and gel spray due to different extruding speed for the gel injector. Results show that the burning behavior of gel droplet in high-pressure oxidant environment is very different from the burning behavior of gel droplet in room pressure conditions. The burning flame structures of gel droplets in high-pressure conditions evolved very violently. The microexplosion phenomenon was more vigorous usually resulting that the maternal droplets broken into several smaller droplets which dropped off during their burning processes. And while the smaller droplets were dropping off, the long-plume from burning flames were protracted behind them. In a moment when the smaller droplets burned out, their burning flames become more luminous instantaneously. And it is interesting that the dropping route of the smaller droplet was not downward vertically rather than floated due to the synthetic effects of gravity, buoyancy, and microexplosion force, and so on. Additionally, the combustion process of gel spray was accelerated as the pressure in chamber was increased.

[Abstract] The present study is focused on measuring the atomization and combustion behavior of gelled propellant. The main aim is to examine the characteristics of the flame structure, the spray breakup length and the spray angle of gelled droplets at different initial chamber conditions and initial spray parameters. Results show that the gelled liquid ligament burns up quickly after only about 0.0099 sec at a certain condition. The gelled liquid ligament burns up more quickly than a gelled droplet. Additionally, the injected velocity and the width of gelled liquid ligament have an influence on the burning time. The spraying ligament would be shrunk and a droplet separated from the liquid ligament during the burning process.

The evolutions of dielectric barrier discharge (DBD) plasma induced starting vortex and the transformation of the DBD plasma induced flow field at different operating pressures are obtained by particle image velocimetry. The results show that the starting vortex will diffuse to the embedded electrode side and then disappear, and the diffusivity will decrease as the time goes on at high operating pressure. But the starting vortex will not change in location, and it will not disappear at low operating pressure. As the operating pressure decreases, the starting time of plasma induced flow field decreases, the ordinate orientation of the induced flowfield increases, and the landscape orientation of the induced flowfield decreases. The form of the induced streamline will come through L→U→V as the pressure decreases. There is no induced vortex in the form of L. There are two induced vortexes in the form of U which lay in the middle and on the right hand of the form U respectively, and there is one induced vortex in the form of V which lays in the middle of form V.

The experiments to generate vortices continuously using sub-microsecond pulsed surface dielectric barrier discharge (SDBD) actuator are conducted by particle image velocimetry (PIV). The double-frequencies actuation mode is presented which includes repetitive pulse frequency and vortex frequency. It is found that the empty zone of PIV particles appears in the place where the particles are quite few even nil during the experiments. When discharges occur the primary empty zone is produced by the micro explosion due to the released heat of plasma, and when discharges end the secondary empty zone appears. The induced flow is farther apart form wall and the influence of wall friction should be suppressed due to primary empty zone. When the secondary empty zone on the left side of actuator exposed electrode is blown away completely, the next actuation can start. In order to control the flow more effectively, the pulse voltage with higher repetitive frequency should be applied. The pulse number during one vortex time should be more than 10. As the pulse number increases, the maximal velocity of induced flow increases but the momentum transfer efficiency decreases. The mechanisms releasing heat and body force can be triggered by using the sub-microsecond pulse SDBD actuator.

Gel propellant has the advantage of controllable flux as liquid propellant and long-term reservation as solid propellant, however, the evaporation and combustion problem of gel spray droplet bores with the gel propellant development and combustor design all the time, and hampers gel propellant practical engineering applications. In this paper, the gel single droplet combustion experiment system is designed and constructed, and then the evaporation and combustion mechanism is explored deeply based on the experimental phenomena of organic gel unsymmetrical dimethylhydrazine (UDMH) single droplet burning in nitrogen tetroxide. The organic gel spray droplet multi-component evaporation model is developed for three different evaporation phases of the gel layer, i.e. the forming, expanding and bursting of the gel layer based on the single droplet evaporation characteristics in experiment, and then the gel single droplet vaporization in high temperature gas phase is numerically simulated and compared with the result of conventional liquid droplet using the elementary model parameters and physic property parameters. The result shows that the gel content on the droplet surface increases slowly at the beginning of evaporation, however it would increase rapidly to a mass fraction of 95% and form the gel layer in a limited time after exceeding a critical evaporation time, which results in surface mass flux dropping to 0 and surface temperature reaching the UDMH boil point rapidly. After the gel layer forming, the droplet radius and surface UDMH vapor mass fraction exhibit oscillation as the swelling-bursting phenomena in experiment. The gel droplet surface temperature holds above the boil point and the mass flux of gel droplet inner boiling evaporation is stronger than the conventional liquid droplet surface steady evaporation which makes the life time of gel droplet much shorter.

Based on the physical processes of dielectric barrier discharge (DBD) and quasi-direct-current (quasi-DC) discharge, the plasma aerodynamic actuation mechanism is analyzed, then the numerical model of plasma aerodynamic actuation is founded, finally the DBD and the quasi-DC discharge plasma flow control processes are simulated in the cases of low velocity and high velocity. The results show that the aerodynamic actuation mechanism of DBD plasma is that the discharge changes three kinds of forces in continuum fluent medium, these being shear stress caused by Newton friction, body force caused by electro hydrodynamic and impulsive active force caused by pressure change, and the main aerodynamic actuation mechanism of DBD plasma is body force caused by electro hydrodynamic. The effect of body force is stronger in near space than in the sea level, plasma induced flow velocity increases in near space. The main aerodynamic actuation mechanism of quasi-DC discharge plasma in supersonic air flow is the thermal mechanism of heat plasma, the exploding wires diathermanous model found in this paper is good for the simulation of the process of surface quasi-DC discharge plasma incident shock. The effect of quasi-DC discharge plasma on the supersonic flow field is conform with the effect of protuberance with a bevel to the supersonic flow field, so it can be used to control the shock wave in supersonic aircraft.