Search

In nature, cellulose nanofibers form hierarchical structures across multiple length scales to achieve high-performance properties and different functionalities. Cellulose nanofibers, which are separated from plants or synthesized biologically, are being extensively investigated and processed into different materials owing to their good properties. The alignment of cellulose nanofibers is reported to significantly influence the performance of cellulose nanofiber-based materials. The alignment of cellulose nanofibers can bridge the nanoscale and macroscale, bringing enhanced nanoscale properties to high-performance macroscale materials. However, compared with extensive reviews on the alignment of cellulose nanocrystals, reviews focusing on cellulose nanofibers are seldom reported, possibly because of the challenge of aligning cellulose nanofibers. In this review, the alignment of cellulose nanofibers, including cellulose nanofibrils and bacterial cellulose, is extensively discussed from different aspects of the driving force, evaluation, strategies, properties, and applications. Future perspectives on challenges and opportunities in cellulose nanofiber alignment are also briefly highlighted.

The stiffness and tensile strength of biopolymers (e.g., polylactic acid (PLA)) are less than desirable for load-bearing applications in their neat form. The use of natural fibers as reinforcements...

The development of new polymer composites is highly dependent on the design of novel fillers that can bring more benefits in the design and control of structure–property–function than conventional ...

Cellulose nanofibrils (CNFs) have been exploited for different applications, such as nanocomposites, gas separation, flexible electronics, and fuel cells, due to their unique properties. To fulfill...

Microfibrillated cellulose (MFC) is widely used as a reinforcement filler for biocomposites due to its unique properties. However, the challenge of drying MFC and the incompatibility between nanocellulose and polymer matrix still limits the mechanical performance of MFC-reinforced biocomposites. In this study, we used a water-based transesterification reaction to functionalize MFC and explored the capability of oven-dried MFC as a reinforcement filler for polylactic acid (PLA). Remarkably, this oven-dried, vinyl laurate-modified MFC improved the tensile strength by 38 % and Young's modulus by 71 % compared with neat PLA. Our results suggested improved compatibility and dispersion of the fibrils in PLA after modification. This study demonstrated that scalable water-based surface modification and subsequent straightforward oven drying could be a facile method for effectively drying cellulose nanomaterials. The method helps significantly disperse fibrils in polymers and enhances the mechanical properties of microfibrillar cellulose-reinforced biocomposites.

Natural fibers have been widely used for reinforcing polymers attributed to their sustainable nature, excellent stiffness to weight ratio, biodegradability, and low cost compared with synthetic fibers like carbon or glass fibers. Thermoplastic composites offer an advantage of recyclability after their service life, but challenges and opportunities remain in the recycling of natural fiber reinforced polymer composites (NFRPCs). This article summarized the effects of reprocessing/recycling on the material properties of NFRPCs. The material properties considered include mechanical performance, thermal properties, hygroscopic behavior, viscoelasticity, degradation, and durability. NFRPCs can generally be recycled approximately 4–6 times until their thermomechanical properties change. After recycling 7 times, the tensile strength of NFRPCs can decrease by 17%, and the tensile modulus can decrease by 28%. The mitigation approaches to overcome degradation of material properties of NFRPCs such as adding functional additives and virgin plastics are also discussed. The main challenges in these approaches such as degradation and incompatibility are discussed, and an effort is made to provide a rationale for reprocessing/recyclability assessment. Future applications of NFRPCs such as additive manufacturing and automotive part use are discussed.

While PLA possesses modest to good strength and stiffness, broader application is hindered by its brittle nature. The aim of this study was to develop strong and tough polymeric materials from renewable biomaterials and understand the underlying interactions and mechanisms. Cellulose nanofibrils (CNFs) and epoxidized soybean oil (ESO) were compounded with poly(lactic acid) (PLA) to create a PLA-CNF-ESO tertiary nanocomposite system. Tensile and dynamic mechanical analyses were performed to see how variations in ESO and CNF content affect mechanical properties such as strength, modulus, ductility, and toughness. It was found that at low CNF levels (10 wt%) the addition of ESO can improve the ductility of the nanocomposites 5- to 10-fold with only slight losses in strength and modulus, while at higher CNF levels (20 and 30 wt%), ESO exhibited little effect on mechanical properties, possibly due to percolation of CNFs in the matrix, dominating stress transfer. Therefore, it is important to optimize CNF and ESO amounts in composites to achieve materials with both high strength and high toughness. Efforts have been made to understand the underlying mechanisms of the mechanical behavior of one class of these composites via thermal, dynamic mechanical, rheological, morphological, and Raman analyses.

Brittleness is a key barrier for poly(lactic acid) (PLA) toward broader applications. Supertough PLA was achieved by simply mixing a low amount (0.5–1 wt %) of organoalkoxysilane with PLA. Three organosilanes, (3-aminopropyl)triethoxysilane (APTES), 3-(triethoxysilyl)propyl isocyanate (ICPTES), and trimethoxymethylsilane (MTMS), were selected for this study to understand how the functional group on a silane affects the behavior of the PLA-silane hybrids. Remarkable improvements in ultimate tensile strain (up to 12 folds) and tensile toughness (up to 10 folds) were observed in APTES- and ICPTES-modified PLA without any loss in tensile strength and modulus. Glass transition temperatures measured by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) did not show any obvious decrease. We propose that in situ condensation of organosilane and grafting of PLA to form a silica-PLA core–shell nanocomplex may be the reason for the improved mechanical properties. Scanning electron microsco...

Advanced templating techniques have enabled delicate control of both nano- and microscale structures and have helped thrust functional materials into the forefront of society. Cellulose nanomaterials are derived from natural polymers and show promise as a templating source for advanced materials. Use of cellulose nanomaterials in templating combines nanoscale property control with sustainability, an attribute often lacking in other templating techniques. Use of cellulose nanofibers for templating has shown great promise in recent years, but previous reviews on cellulose nanomaterial templating techniques have not provided extensive analysis of cellulose nanofiber templating. Cellulose nanofibers display several unique properties, including mechanical strength, porosity, high water retention, high surface functionality, and an entangled fibrous network, all of which can dictate distinctive aspects in the final templated materials. Many applications exploit the unique aspects of templating with cellulose nanofibers that help control the final properties of the material, including, but not limited to, applications in catalysis, batteries, supercapacitors, electrodes, building materials, biomaterials, and membranes. A detailed analysis on the use of cellulose nanofibers templating is provided, addressing specifically how careful selection of templating mechanisms and methodologies, combined toward goal applications, can be used to directly benefit chosen applications in advanced functional materials.

Cellulose nanomaterials (CNMs) naturally exist in plant biomass. The success of extraction of CNMs opened up a new era of using plant biomass for innovative industrial applications. Because CNMs are abundant, renewable, biodegradable, transparent, light weight and low in cost, they are ideal materials for large volume applications such as packaging, automotive, building and infrastructure. In many potential application areas, CNM-enabled products appear in a composite form, mostly polymer composites. The industrial-scale manufacturing of CNM/thermoplastic composites remains as a set of unsolved problems for academia and industry. A prime challenge in applications is the nanoscale dispersion of CNMs in thermoplastic matrices during melt processing. Both bench-scale and pilot-scale studies have been conducted to solve the dispersion issue of CNMs. In this article, research related to the dispersion of CNMs in thermoplastic matrices during melt processing were critically reviewed. All research papers were classified into three groups: chemically-aided dispersion, physically-aided dispersion and mechanically-aided dispersion. Numerous factors affect the CNM dispersion and the mechanical performance of its nanocomposites. There are material-related factors, including CNM types and forms, polymer matrices, surface modification, coupling agents, etc. Extrusion processing parameters also play a significant role, covering screw rotation speed, extrusion barrel temperature settings and screw design. In addition, the material-related factors interact with the processing-related factors. Understanding all factors and their interactions are important for moving CNM nanocomposites research a step further towards industrial-relevant production, which is the final ambitious goal of this manuscript.

Advanced biocomposites reinforced by abundant biomass-derived fillers can add a revenue stream to enhance the economic viability of biofuel production chains and the energy efficiency of the composite industry. However, the low stiffness of biopolymers limits their use in structural applications. Poplar fibers (mesh size: l -lysine). As a benefit of the amino acid treatment, the tensile Young's moduli of the lysine/poplar/PLA composites increased by up to 68% with the addition of a small amount of lysine, compared with neat PLA. At the same time, the tensile strength, failure strain, and Young's modulus of the poplar/PLA composites all increased after adding only 0.1 wt % of lysine. It has been observed that the lysine content has a significant effect on the decomposition temperature, complex viscosity, storage modulus, crystallization temperature, and crystallinity of composites. The fracture surfaces of the composites with an optimum lysine content had fewer voids and were more compact compared with composites without any lysine. The pores on the surfaces of poplar fibers became more available for the penetration of PLA molecules as a result of lysine addition. Therefore, this study presents a facile method for reinforcing biocomposites with extremely low-cost and environmentally friendly biofillers.

Cellulose nanocrystal (CNC)-based composite films were prepared as a solid electrolyte for alkaline fuel cells. Poly(vinyl alcohol) (PVA) and silica gel hybrid were used to bind the CNCs to form a robust composite film. The mass ratio (i.e., 1 : 1, 1 : 2) of PVA and silica gel was tuned to control the hydrophobicity of the resulting films. Composite films with a range of CNC contents (i.e., 20–60%) were prepared to demonstrate the impact of CNCs on the performance of these materials as a solid electrolyte for alkaline fuel cells. Different from previously reported cross-linked polymer films, CNC-based composite films with 40% hydrophobic binder (i.e., PVA : silica gel = 1 : 2) exhibited simultaneous low water swelling (e.g., ∼5%) and high water uptake (e.g., ∼80%) due to the hydrophilicity and extraordinary dimensional stability of CNCs. It also showed a conductivity of 0.044 and 0.065 S cm−1 at 20 and 60 °C, respectively. To the best of our knowledge, the film with 60% CNC and 40% binder is characterized by the lowest hydroxide conductivity-normalized swelling ratio. Decreased CNC contents (i.e., 40 and 20%) resulted in comparable hydroxide conductivity but a greater swelling ratio. These results demonstrate the advantage of CNCs as a key component for a solid electrolyte for alkaline fuel cells over conventional polymers, suggesting the great potential of CNCs in improving the dimensional stability while maintaining the conductivity of existing anion exchange membranes.

While polymer additive manufacturing (AM) has advanced significantly over the past few decades, the limitations in material properties, speed of manufacture, and part size have relegated this technology to the space of rapid prototyping rather than the legitimate manufacture of end-use parts. Carbon fiber offers a low density, a low coefficient of thermal expansion, and high thermal conductivity and is an ideal material for bringing polymer-based AM from the realm of form and fit to that of form, fit, and function. Use of carbon fiber in AM can improve material properties, reduce the time required to manufacture functional parts compared with traditional subtractive technologies, and reduce warping, thereby enabling a larger possible build envelope. Therefore, the addition of carbon fiber to various AM technologies is of increasing interest in academic and industrial communities. This paper examines the work performed in this fast-growing area to date. Specifically, the effects of fiber reinforcement on the structure and mechanical properties of 3D printed parts are investigated within the body of literature. Upper bounds for tensile properties of carbon fiber composites are theoretically evaluated and compared with experimentally measured values. Moreover, current and potential applications of additively manufactured carbon fiber composites in the context of desktop 3D printing and big area AM are discussed. Recent innovations and industry breakthroughs in this field are also examined. This review is intended to organize and synthesize the present body of work surrounding AM of carbon fiber reinforced plastics, identify the most promising technologies, and prescribe viable research and development paths forward to advance AM from the application space of rapid prototyping to that of functional, load-bearing, end-use parts.

Additive manufacturing, diverging from traditional manufacturing techniques, such as casting and machining materials, can handle complex shapes with great design flexibility without the typical waste. Although this technique has been mainly used for rapid prototyping, interest is growing in using this method to directly manufacture actual parts of complex shape. To use 3D-printing additive manufacturing in wide spread applications, the technique and the feedstock materials require improvements to meet the mechanical requirements of load-bearing components. Thus, we investigated the short fiber (0.2 mm to 0.4 mm) reinforced acrylonitrile-butadiene-styrene composites as a feedstock for 3D-printing in terms of their processibility, microstructure and mechanical performance; and also provided comparison with traditional compression molded composites. The tensile strength and modulus of 3D-printed samples increased ~115% and ~700%, respectively. 3D-printer yielded samples with very high fiber orientation in printing direction (up to 91.5 %), whereas, compression molding process yielded samples with significantly less fiber orientation. Microstructure-mechanical property relationships revealed that although the relatively high porosity is observed in the 3D-printed composites as compared to those produced by the conventional compression molding technique, they both exhibited comparable tensile strength and modulus. Furthermore, this phenomena is explained based on the changes in fiber orientation, dispersion andmore » void formation.« less

Nanocellulose materials are nano-sized cellulose fibrils or crystals produced by bacteria or derived from plants. These materials exhibit exceptional strength characteristics, light weight, transparency, and excellent biocompatibility. Compared with some other nanomaterials, nanocellulose is renewable and less expensive to produce, and a wide range of applications for nanocellulose has been envisioned. The areas most extensively studied include polymer composites and biomedical applications. Cellulose nanofibrils and nanocrystals have been used to reinforce both thermoplastic and thermoset polymers. Given the hydrophilic nature of these materials, the interfacial properties with most polymers are often poor; thus, various surface modification procedures have been adopted to improve the interaction between polymer matrix and cellulose nanofibrils or nanocrystals. The applications of nanocellulose as a biomaterial also have been explored, including wound dressing, tissue repair, and medical implants. Nanocellulose materials for wound healing and periodontal tissue recovery have become commercially available, demonstrating the great potential of nanocellulose as a new generation of biomaterials.

Seven oligomeric fractions of well-defined composition and molecular weight distribution were generated via supercritical extraction from an isotropic petroleum pitch (M-50) and used as precursors for the production of activated carbon fibers. Both isotropic and mesophase-containing fractions were produced, so that the effects of molecular order and molecular weight could be separated. Carbonization weight loss was found to gradually decrease with increasing molecular weight (and oligomeric number), with mesophase content not being a significant factor. Similar behavior was observed for activation weight loss when the precursors were isotropic; however, even modest increases in molecular order significantly retarded the activation process and resulted in dramatic drops in specific pore volume. A 100% dimer precursor fraction with an average molecular weight of 480 Da produced activated carbon fibers with the highest (specific) pore volume, and the highest pore volume in the range desired for hydrogen adsorption (6–7 A). Even for isotropic precursors, decreases in pore volume with increasing molecular weight were observed. The incremental pore size distribution generated from the nitrogen adsorption data consisted of discrete peaks, which is consistent with the formation of pores by the removal of short micrographene layers, with each layer being formed from an individual oligomeric molecule.

ORNL worked with American Process Inc. to demonstrate the potential use of bio-based BioPlus® lignin-coated cellulose nanofibrils (L-CNF) as a reinforcing agent in the development of polymer feedstock suitable for additive manufacturing. L-CNF-reinforced polylactic acid (PLA) testing coupons were prepared and up to 69% increase in tensile strength and 133% increase in elastic modulus were demonstrated.

The effect of palladium acetylacetonate on the pore structure evolution of isotropic petroleum pitch-based activated carbon fibers (ACFs) is characterized by comparing the pore structure evolution ...

Palladium-doped activated carbon fibers are being evaluated as candidate materials for enhanced hydrogen storage at near ambient conditions. Pd-doped fibers were spun using a Pd salt mixed with an isotropic pitch precursor. Experimental techniques such as in situ X-ray analysis, thermogravimetric studies, scanning transmission electron microscopy and gas adsorption were employed to understand how processing conditions for the production of Pd-doped activated carbon fibers affect the microstructure, pore development, and dispersion of metal particles throughout the fibers. The results showed that PdO phase is present in the stabilized fibers and that this oxide phase is stable up to about 250 °C. The oxide phase transforms into Pd metal with increasing heat treatment temperature, going through the formation of an intermediate carbide phase. Sintering of Pd particles was observed with heat treatment at temperatures over 750 °C. It was also found that pore development during physical activation with CO2 was not significantly affected by the presence of Pd particles within the fibers.

Efficient storage of hydrogen for use in fuel cell-powered vehicles is a challenge that is being addressed in different ways, including adsorptive, compressive, and liquid storage approaches. In this paper we report on adsorptive storage in nanoporous carbon fibers in which palladium is incorporated prior to spinning and carbonization/activation of the fibers. Nanoparticles of Pd, when dispersed in activated carbon fibers (ACF), enhance the hydrogen storage capacity of ACF. The adsorption capacity of Pd-ACF increases with increasing temperature below 0.4 bar, and the trend reverses when the pressure increases. To understand the cause for such behavior, hydrogen uptake properties of Pd with different degrees of Pd-carbon contact (Pd deposited on carbon surface and Pd embedded in carbon matrix) are compared with Pd-sponge using in situ XRD under various hydrogen partial pressures (Rietveld refinement and profile analysis of diffraction patterns does not show any significant changes in carbon structure even under 10 bar H2. Pd forms β PdH0.67 under 10 bar H2, which transforms to α PdH0.02 as the hydrogen partial pressure is decreased. However, the equilibrium pressure of transition (corresponding to a 1:1 ratio of α and β phases) increases with increasing the extent of Pd-carbon contact. This pressure is higher for Pd embedded in carbon than for Pd deposited on carbon surface. Both these Pd-carbon materials have higher H2 desorption pressure than pure Pd, indicating that carbon “pumps out” hydrogen from PdHx and the pumping power depends on the extent of Pd-carbon contact. These results support the spillover mechanism (dissociative adsorption of H2 followed by surface diffusion of atomic H).