Search

The rational design of perfluorinated amphiphiles to control the supramolecular aggregation in an aqueous medium is still a key challenge for the engineering of supramolecular architectures. Here, the synthesis and physical properties of six novel non-ionic amphiphiles are presented. The effect of mixed alkylated and perfluorinated segments in a single amphiphile is also studied and compared with only alkylated and perfluorinated units. To explore their morphological behavior in an aqueous medium, dynamic light scattering (DLS) and cryogenic transmission electron microscopy/electron microscopy (cryo-TEM/EM) measurements are used. The assembly mechanisms with theoretical investigations are further confirmed, using the Martini model to perform large-scale coarse-grained molecular dynamics simulations. These novel synthesized amphiphiles offer a greater and more systematic understanding of how perfluorinated systems assemble in an aqueous medium and suggest new directions for rational designing of new amphiphilic systems and interpreting their assembly process.

PEG-modification is a proven method to enhance the hydrophilicity, protein resistance, and anti-biofouling properties of polymer coatings. It is considered as the gold standard interfacial modification technique such that the higher PEG content, the higher hydrophilicity, and lower protein adsorption, i.e., the initial stage of the biofouling process. Nevertheless, increasing the PEG content causes a higher water uptake, which declines the polymer mechanical strength and increases its hydrolytic degradation rate. Thus, an effective strategy to produce a limited-water-absorbing PEG-modified polymer is to force the majority of PEG molecules to migrate towards the interfacial region while the modification takes place. In the current paper, we report the synthesis and characterization of crosslinked polycarbonate-based polyurethanes (PU) containing methoxy polyethylene glycol (mPEG) dangling chains. We show that the simultaneous incorporation of a limited amount of a low-surface-energy dangling chain, i.e., 1-octadecanol (oDEC), along with mPEG, results in a considerably higher mPEG surface concentration, according to X-ray photoelectron spectroscopy (XPS), and a significantly lower water contact angle (WCA), up to 45° lower. We also put forward a reasonable mechanism for our outstanding observation and verified it through extensive experiments, e.g., dynamic WCA, Atomic force microscopy (AFM), and XPS. Moreover, we outline a delicate dynamic WCA experimental protocol, by which the smart and responsive behavior of our coatings is illustrated. Eventually, we examined the mixed hydrophobic/hydrophilic dangling chains strategy for low-protein adsorption applications, in which a great potential has been discovered.

Incorporation of hydrophilic and hydrophobic agents into a polymer backbone is an effective approach to control its interfacial characteristics. Segmented polyurethanes (PUs) are easy-fabricating and cost-effective candidates in this respect. In this work, we have synthesized polycarbonate (PC)-based PUs containing hydrophilic Polyethylene glycol (PEG) and hydrophobic Polyhedral Oligomeric Silsesquioxane (POSS) in the lab as well as in molecular dynamics simulations. We employed several experimental techniques and a coarse-grained (CG) molecular dynamics (MD) method to evaluate the morphology and microphase arrangement of PUs. We successfully synthesized superior hydrophilic and hydrophobic coatings by replacing some parts of the soft segment (PC) with PEG and the chain extender (1,4-butandiol) with POSS, respectively. Our CG MD simulations showed that POSS is dispersed in PC uniformly, while PEG is completely phase separated from PC and formed a lamellar structure. This was also confirmed by experimental thermal analysis. Eventually, water contact angle (WCA) measurements proved development of very hydrophilic (PU-PEG), slightly hydrophilic (PU), and very hydrophobic (PU-POSS) coatings. The surface free energy analysis indicated that POSS decreases polar and apolar components of surface free energy, while PU-PEG exhibits omniphilic behavior. The presence of PEG and POSS on the surface was also confirmed by contact angle and AFM measurements. According to MTT and LDH assays, PEG and POSS incorporation significantly enhanced the biocompatibility of PU such that PU-PEG and PU-POSS coatings become prospective candidates for biomedical applications.

A kinetic Monte Carlo method to simulate photodegradation of a polymer coating is applied to the weathering process of a polyester-urethane clearcoat during artificial exposure under different conditions. Firstly, the optimised simulation parameters that yield the best match with experimentally measured results on the depth-resolved ester and urethane bond fractions are determined and compared for two different aerobic exposure experiments (one in a Weather-Ometer (WOM) and one in a Suntest equipment). Secondly, several other quantities that are obtained from the simulations, but cannot be determined experimentally, are compared, such as the fraction of newly formed crosslink bonds, absorptivity states, oxidised states, the fraction of radicals, the concentration of oxygen and the total amount of remaining material. Depth-inhomogeneity of the rate of photon absorption leads to the formation of distinct depth gradients in the WOM simulation, while a much more homogeneous evolution is obtained for the Suntest-air simulation. Photo-oxidative damage in the WOM simulation is more concentrated on the upper layer of the coating, resulting in the extensive evaporation of highly oxidised material, whereas degradation in the Suntest-air simulation is more spread out over the entire coating thickness, resulting in less material loss.

The influence of the conditions of artificial degradation experiments on the photodegradation process of polyester-urethane clearcoats has been studied by comparing three types of exposure experiments with different conditions regarding the spectral power distribution (SPD), the exposure atmosphere (aerobic and anaerobic) and the presence of water. The presence of short wavelengths (λ

In this work we simulate the full sequence of steps that are also typically performed in an experimental approach when studying photo-degradation of a polymer coating, namely, i) sample preparation, ii) photo-degradation and iii) thermo-mechanical analysis of the material during photo-degradation. In the current paper, we focus on performing several molecular dynamics simulations to study the thermo-mechanical properties of a virgin thermoset coating as well as degraded ones. Using an atomistic structure that is obtained by fine-graining the mesoscopic structure, we obtain consistent correlations between the simulated thermo-mechanical properties of the material and those measured experimentally. In addition, it is shown that by using oscillatory strain fields in MD - instead of the commonly applied linear tensile/compression strain fields – one can acquire greater knowledge on the structure-property relation of polymeric materials. Eventually, we show that our simulation approach gives rise to a remarkable insight into the mechanism of the photo-degradation process.

This paper is devoted to the surface analysis of a polyester-urethane coating during weathering under different conditions using artificial weathering machines. By means of atomic force microscopy (AFM), the evolution of the surface topology of the coatings is studied. Degradation is shown to be a laterally inhomogeneous process. The presence of water facilitates material removal and leads to an increase in the surface roughness and consequently a gloss loss. In addition, by comparing degradation under aerobic and anaerobic conditions, it is shown that oxidation reactions are the main cause of lateral inhomogeneous degradation of coatings.

Designing surfaces with patterns of varying wettability is of significant importance for many applications. This fascinating feature is inspired by nature where it is vital for the survival of some living creatures. This research shows that an inherent incompatibility between different soft segments of segmented polyurethanes can play a pivotal role in designing such surfaces. We employed experimental techniques as well as coarse-grained molecular dynamics (CG MD) simulations to illustrate the microphase separation between soft segments with significantly different wettability. We started with poly(hexamethylene carbonate) polyurethane and partially replaced the polycarbonate diol (PC), the hydrophobic soft segment, with poly (ethylene glycol) (PEG), the superhydrophilic soft segment. Experimental analyses indicated a phase separation between PEG and PC, as soft segments, and our simulations merely confirmed it. This led to a core-shell morphology in which the hard segments are squeezed between two incompatible soft segments. Our combined simulation and experimental analyses proved a concurrent phase mixing of hard/soft segments with phase separation between soft segments. Moreover, the CG MD simulations elucidated the evolution of microphase organization as the polymerization proceeds and our further analysis shed light on the microarchitecture of the individual PU chains.

Transmission FTIR analysis of polyester-urethane coatings (PUC), that were degraded under different accelerated laboratory weathering conditions, are compared. The aim of this comparison is to deepen our insight into the chemical pathways of weathering of polyester-urethane coatings. We monitored the chemical changes for different environments, such as aerobic or anaerobic conditions as well as wet or dry conditions, in order to increase our insight into the effect of each individual stress factor, i.e., photons, oxygen, temperature and water, on the chemical pathways of weathering. We showed that the degradation of urethane groups proceeds via photo-oxidative pathways and that the ester groups mainly degrade via photolytic reactions. The ester bond scission accelerates after an initially-slow-rate stage of weathering in the presence of urethane groups. This is due to an increase in the optical absorptivity of the coating as a result of degradation under anaerobic conditions, as shown before. By means of a kinetic analysis using a combination of FTIR and UV–Vis spectroscopy results (obtained before), we found that a first-order kinetic model can perfectly describe the rate of ester bond scission during the weathering and that the increase in the rate of reaction is due to the increase in the light absorptivity of the coating as a result of degradation. Finally, using the interference fringes of FTIR spectra, we showed that evaporation and water-caused removal of degraded material cause a particularly pronounced decay in the thickness of the coating. In the absence of water spray, the material loss takes place in the same period as urethane groups decompose and stops afterwards, even though the ester bond scission proceeds with higher rates. This supports the hypothesis of photo-oxidative pathways for the urethane group decomposition and photolytic mechanisms for ester bond scission. Dark experiments showed that PUC coatings are highly resistant to hydrolysis and thermal degradation.

The effect of graphene (G) and graphene oxide (GO), used as the nanofiller in polymer nanocomposites (NC), on the structural and dynamic properties of polymer chains, has been studied by means of molecular dynamics (MD) simulations. Two polymers, i.e., poly(propylene) and poly(vinyl alcohol), are employed as matrices to cover a wider range of polymer�filler interactions. The local structural properties, e.g., density profile, average Rg, and end-to-end distance as well as dynamic properties, e.g., estimated translational and orientational relaxation times, of polymer chains are studied. In addition, the interaction energies are estimated between polymers and nanofillers for different hybrid systems using MD pullout simulations. Strong heterogeneities in polymer structural and dynamic properties have been observed such that chains are more oriented and exhibit slower dynamics in the vicinity of the nanofillers (G and GO) as compared to bulk. It is also found that the orientation of polymer chains at the interface is more influenced by the nanofiller in such a way that the more oriented polymer chains are observed in G-based NC for both polymers. However, the immobilization of polymer chains at the interface proves to be very much dependent on the polymer�filler interactions. (Figure presented.). Scopus

Chemical degradation of polymer coatings via a photo-oxidative pathway, denoted as photo-degradation, results in physical changes which, in spite of the long service life of coatings, eventually lead to failure of the material. Conventional molecular simulations cannot cope with this process with its wide range of time and length scales, related to the rare occurrence of ‘degradation events’ as compared to the time scale of structural relaxation of the polymer chains. Therefore a combination of suitable simulation techniques is needed to overcome this problem. By coupling a kinetic Monte Carlo simulation to a Dissipative Particle Dynamics method, a novel simulation approach has been developed that makes it possible to take into account chemical and physical pathways of the photo-degradation process. For a model polyester-urethane coating photo-degradation under inert conditions was studied with and without taking structural relaxation into account as well as by varying the ratio of reaction rate constants. For the model coating studied, taking physical relaxation into account proved to be essential for modeling the photo-degradation process.

In this article we studied the evolution of thermomechanical properties of a polyester-urethane coating during degradation under different degradation conditions, i.e., aerobic and anaerobic conditions with and without dry/wet cycling during degradation. Dynamic mechanical and thermal analyses show that under aerobic conditions the coatings become stiffer and more brittle in the glassy state. This stiffening is probably due to the increase in the amount of hydrogen bonding and the formation of oxidized groups which increase the polarity of the material and enhance the interactions of the polymer segments. However, oxidation reactions result in a considerable decrease in cross-link density and stiffness in the rubbery state. Both changes, in the glassy and rubbery states, give rise to development of internal stresses. These stresses increase as the degradation process proceeds. Nevertheless, for samples exposed to anaerobic conditions, the stiffness remains constant in the glassy state and the cross-link density slightly increases as a result of degradation. This reconfirms the dominance of the effect of oxidation reactions on the mechanical failure of the coatings. Oxygen permeation measurements show a more-or-less time-independent diffusion coefficient and a gradual decrease in solubility of oxygen as a function of exposure time. This results in a slight decrease in oxygen permeation (mainly in the early stage of the degradation) as degradation proceeds. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 659–671

Polyester-urethane resins are important candidates for high performance, outdoor coating applications. Despite their relevance, quantitative information regarding the photodegradation of these materials is scarcely available. In the present study, a model polyester-urethane clearcoat without additives is artificially degraded and the changes in optical properties and chemical composition are studied by UV-VIS spectroscopy and FTIR-ATR microscopy, respectively. The change of the optical properties throughout the coating thickness is quantified and interpreted using a newly developed optical model. Chemical changes are quantified in a depth-resolved manner by combining FTIR-ATR microscopy with optical profilometry in order to visualise the time evolution of compositional gradients during photodegradation by accurate assignment of the correct depth position to all recorded ATR spectra. The rate of change for the concentration of several chemical entities in the model polyester-urethane was found to become constant after the initial stage of weathering. The loss of urethane crosslinks in the coating occurs faster and to a much larger extent as compared to ester bond scission. Results from the optical and the chemical characterisation are combined to propose a kinetic model for ester bond photolysis that provides an estimate of the quantum efficiency of this process.

Having phase-separated conductive and less-conductive domains is a common morphology in semiconducting polymer blends as it exists in the case of PEDOT:PSS, which is a representative example with a wide range of applications. In this paper, we constructed atomistic models for the interface between the PEDOT-rich (conductive) grains and the PSS-rich (less-conductive) phase through molecular dynamics simulations. Our models are obtained from experimentally relevant compositions, based on precise force field parameters, and through a robust relaxation procedure. We show that both PEDOT-rich and PSS-rich phases consist of PEDOT lamellae embedded in PSS chains. The size of these lamellae depends on the PEDOT concentration in each phase and our model predictions are in quantitative agreement with the experimental data. Furthermore, our models suggest that neither the phases nor the interfaces are entirely connected by π-π stacking. Thus, inter-lamellae tunnelling is essential for both intra- and inter-grain charge transport. We also show that a small increase (≈8 wt%) in the PEDOT concentration results in rather larger lamellae sizes, considerably more oriented lamellae, and slightly better inter-lamellae connectivity, which result in enhanced intra-grain conductivity. Moreover, we show how enhancing phase separation between PEDOT-rich and PSS-rich domains (similar to the effect of polar co-solvents)