Search

Summary: In this paper, a new model for joint dynamic friction of industrial robot manipulators is presented. In particular, the effects of the temperature in the joints are considered. A polynomial-based model is proposed and the parameter estimation is performed without the need of a joint temperature sensor. The use of an observer is then proposed to compensate for the uncertainty in the initial estimation of the temperature value. A large experimental campaign show that the model, in spite of the simplifying assumptions made, is effective in estimating the joint temperature and therefore the friction torque during the robot operations, even for values of velocities that have not been previously employed. [ABSTRACT FROM AUTHOR]

Abstract: The paper presents the results of a research project whose aim is investigating, from both a theoretical and an experimental point of view, all the aspects connected to the optimal design and use of a 6 DoF draw-wire sensors based measuring system in the kinematic calibration of industrial robots context. One essential operation in calibration is the measurement of the pose of the robotic gripper in a predefined set of points inside the working space. For this purpose optical devices, like laser trackers, are usually employed due to their precision, although they are very expensive. Therefore, the study of a low-cost measuring system and the investigation of the reachable performances could represent a relevant outcome in the evolution of the calibration task. With this aim the design of a wire-sensors based measuring system was developed and applied to a six revolute degrees of freedom anthropomorphic robot. In a preliminary phase, with the aid of simulations tools, the measuring system was optimized to obtain isotropic accuracy and high sensitivity, while in the following experimental phase the same system was employed for the kinematic calibration of the robot, achieving an accuracy lower than the robot repeatability, which practically represents a physical limit. [Copyright &y& Elsevier]

In this paper, we propose a new method, which is based on an iterative-learning-control (ILC) algorithm, for the contour tracking of an object of unknown shape performed by an industrial robot manipulator. In particular, we consider (both implicit and explicit) hybrid force/velocity control whose performance is improved by repeating the task. Here, a time-based reference signal is not present, and therefore, a new approach has been developed, which is different from the typical applications of ILC. Experimental results show the effectiveness of the technique. [ABSTRACT FROM AUTHOR]

In this paper a gain scheduling approach is proposed for the hybrid force/velocity control of an industrial manipulator employed for the contour tracking of objects of unknown shape. The methodology allows to cope with the configuration dependent dynamics of the manipulator during a constrained motion and therefore a significant improvement of the performance results. Experimental results obtained with an industrial SCARA manipulator demonstrate the effectiveness of the technique. [ABSTRACT FROM AUTHOR]

This paper presents a methodology for the design of PKMs (parallel kinematic machines) with defined isotropy and stiffness. Partial isotropy or full isotropy can be achieved by suitable design choices. The former is useful for five axis applications, while the latter for six axis manipulators. The paper summarizes the concept of full and partial isotropy, and for a wide class of hexapods defines in analytical form the conditions to achieve it exactly. These conditions can be used to design isotropic parallel manipulators. The methodology requires that the six legs have to be divided into two groups (terns). The legs belonging to one tern are mutually identical and are positioned with radial symmetry with respect to the TCP (tool center point). The paper shows that the manipulator structure can be defined in term of 13 design parameters, the value of six of them are chosen in order to achieve the required isotropy and stiffness properties, while the remaining seven parameters can be used to optimize the structure. The design criterion here presented assures that stiffness isotropy, force, and velocity isotropy are all achieved contemporarily. This methodology can be practically applied to a large family of hexapods. © 2005 Wiley Periodicals, Inc. [ABSTRACT FROM AUTHOR]

This article presents and compares three algorithms for the geometric parameter identification of industrial robots to increase its accuracy (static calibration). The estimation is based on the measure of the gripper pose errors when the robot follows suitable trajectories. The algorithms are general and can be applied to any robot providing that its kinematics is known. After a theoretical introduction to the general methodologies, these are applied to a selective compliance assembly robot arm (SCARA) robot analyzing its performance (precision, efficiency). Experimental results obtained with three methodologies are presented and discussed. The measure of the gripper pose error is based on a laser triangulation technique whose working principles are also recalled. © 2000 John Wiley & Sons, Inc. [ABSTRACT FROM AUTHOR]

This paper describes the results of dynamic tests performed to study the robustness of a dynamics model of an industrial manipulator. The tests show that the joint friction changes during the robot operation. The variation can be identified in a double exponential law and thus the variation can be predicted. The variation is due to the heat generated by the friction. A model is used to estimate the temperature and related friction variation. Experimental data collected on two robots EFORT ER3A-C60 are presented and discussed. Repetitive tests performed on different days showed that the inertial and friction parameters can be robustly estimated and that the value of the measured joint friction can be used to estimate the unexpected conditions of the joints. Future applications may include sensorless identification of collisions, predictive maintenance programs, or human–robot interaction. [ABSTRACT FROM AUTHOR]

The present paper analyses the potential dynamic performance of a novel redundant SCARA robot, currently at the stage of a functional design proposed by a renowned robot manufacturer. The static and dynamic manipulability of the new concept is compared with the conventional model of the same manufacturer by means of computer simulation in typical pick and place tasks arising from industry. The introduction of a further revolute joint in the SCARA robot kinematics leads to some improvements in the kinematic and dynamic behaviour at the expense of a greater complexity. In this paper, the potential of a redundant SCARA architecture in cutting cycle-times is investigated for the first time in performing several tasks. It is shown that, in order to exploit the possible enhancements of the redundant structure, the whole manipulator, mechanics and control must be redesigned according to specific tasks aiming at the optimization of their cycle-time. [ABSTRACT FROM AUTHOR]

This paper presents the kinematics analysis of a class of spherical PKMs Parallel Kinematics Machines exploiting a novel approach. The analysis takes advantage of the properties of the projective angles, which are a set of angular conventions of which their properties have only recently been presented. Direct, inverse kinematics and singular configurations are discussed. The analysis, which results in the solution of easy equations, is developed at position, velocity and acceleration level. [ABSTRACT FROM AUTHOR]