Search

Addressing the strength-toughness trade-off issue has been highly desirable for high strength Mg alloys. Herein, an Mg-9Gd-4Y-1Zn-0.5Zr (wt %) alloy is designed, and a yield strength of 430 MPa and plane-strain fracture toughness K I c of 23.1 MPa · m1/2 are achieved. Intrinsically, significant stress dissipation is induced by interactions between the tensile twinning and the kinking of the lamellar γ' phase, leading to increased K I c. Owing to the residual stress release, the fracture resistance is remarkably improved by the non-basal 〈 a〉 and 〈 c + a〉 dislocations activated in the fine dynamic recrystallized (DRXed) grains. Extrinsically, the microcracks initiated along the interfaces between lamellar γ' phase and α-Mg matrix facilitate the reduction of local crack-driving forces, resulting in an enhanced K I c. Moreover, the underlying toughening mechanisms were revealed, including the crack propagation path deflection caused by coarse deformed grains and microcrack shielding by the long-period stacking ordered (LPSO) and lamellar γ' phases. [Display omitted] [ABSTRACT FROM AUTHOR]

The effects of bimodal microstructure on the tensile properties and fracture toughness of Mg-9Gd-4Y-0.5Zr alloys were investigated. The Mg-9Gd-4Y-0.5Zr alloy was extruded at different temperatures to produce samples with bimodal and fully dynamic recrystallized (DRXed) grain structures. The results show that the bimodal grain structure exhibits a better combination of yield strength (YS of 277 MPa) and plane strain fracture toughness (K I c = 21.5 MPa m1/2), compared to the fully DRXed microstructure (YS of 207 MPa, K I c = 16.3 MPa m1/2). The fracture mechanisms for the bimodal and fully DRXed microstructures are the ductile fracture mode and quasi-cleavage fracture mode, respectively. Both hetero-deformation induced (HDI) strengthening effect and strong basal texture can contribute to high tensile strength in the bimodal grain structured sample. As compared to the sample with fully DRXed microstructure, the stronger strain hardening capacity and larger hardened region around the crack tip in the bimodal grain structured sample can bring about the improvement in the fracture toughness. The tortuous crack propagation path and the hindrance of propagating crack by the un-DRXed grains result in larger fracture resistance and more energy dissipation. The increase of geometrically necessary dislocation (GND) density and the activation of non-basal dislocations also have positive effects on the fracture toughness of the samples with bimodal grain structure. The fracture toughness is effectively improved via intrinsic and extrinsic toughening mechanisms associated with the bimodal microstructure. [ABSTRACT FROM AUTHOR]

Abstract: Extruded Mg–8.2Gd–3.8Y–1Zn–0.4Zr (wt%) alloy was subjected to ageing treatment at 200°C. The microstructures, textures and mechanical properties of the as-extruded and peak-aged alloys were investigated. Recrystallization occurred during ageing treatment. A large number of β′ phases were observed in the peak-aged alloy, accompanied with the decrease of the volume fraction of LPSO phases. A basal fiber texture and an unusual texture component with basal planes perpendicular to the extrusion direction were found in the as-extruded alloy, and the basal fiber texture was strengthened after ageing treatment. The peak-aged alloy exhibited a tensile yield strength (TYS), an ultimate tensile strength (UTS) and an elongation to failure of 395MPa, 470MPa and 8%, respectively, at ambient temperature, and 271MPa, 311MPa and 19%, respectively, at 300°C. The superior strength of the peak-aged alloy was mainly attributed to the precipitation of fine β′ phases, the remaining LPSO phases and the texture modification. [Copyright &y& Elsevier]

Abstract: The microstructure and mechanical properties of Mg–8.2Gd–3.8Y–1.0Zn–0.4Zr (wt%) alloy sheets produced by combined processes of extrusion, large-strain hot rolling and ageing treatment were investigated. The sheet rolled at 300°C was mainly composed of deformed grains while that rolled at 400°C was fully recrystallized, and the LPSO phase distributed at the grain boundaries in both sheets. The sheet rolled at 300°C and then peak-aged at 200°C exhibits 0.2% proof stress (PS) of 454MPa, ultimate tensile strength (UTS) of 469MPa and elongation to failure of 1.3% at ambient temperature, and 0.2% PS of 413MPa, UTS of 457MPa and elongation to failure of 6.8% at 200°C, respectively. While the sheet rolled at 400°C and peak aged at 200°C had lower 0.2% PS and superior ductility. The improvement of strength is ascribed to the fine β′ phase precipitated within the grains, the LPSO phase and dispersed cuboid Mg–Gd–Y containing phase located at the grain boundaries. [Copyright &y& Elsevier]

Abstract: In this research, the as-cast and as-homogenized Mg–8.2Gd–3.8Y–1.0Zn–0.4Zr alloy were subjected to the hot rolling with the same processing parameters. The microstructure and mechanical properties of the two kinds of as-rolled sheets were investigated. The sheet rolled from the as-cast alloy was mainly composed of recrystallized α-Mg grains surrounded by Mg3(Gd,Y) eutectic compounds. While the sheet rolled from the as-homogenized alloy was composed of large deformed grains with long-period stacking ordered (LPSO) phase inside and fewer recrystallized α-Mg grains, and exhibited higher strength due to the deformed grains with stronger basal texture and larger volume fraction of long-period stacking ordered (LPSO) phase. [Copyright &y& Elsevier]

Abstract: Mg–8.2Gd–3.8Y–1.0Zn–0.4Zr alloy sheets containing long period stacking ordered (LPSO) phase were prepared by hot rolling at 400°C with total reduction of 96%. Microstructure evolution of the sheets during hot rolling was investigated, and its influence on mechanical properties was discussed. Twinning occurred during the early stage of hot rolling, and disappeared after total reduction higher than 89%. Average grain size was gradually refined, microstructure became much more homogeneous and volume fraction of LPSO phase decreased with increasing rolling reduction. Furthermore, the type of LPSO phases far from and near the block shaped phases were identified to be different. Basal texture was obtained during rolling process, but the intensity declined with the further rolling, which is mainly due to the dynamic recrystallization and the addition of RE elements. The as-rolled sheet with 96% reduction shows excellent mechanical properties: yield strength of 318MPa, ultimate tensile strength of 403MPa and elongation to failure of 13.7% at ambient temperature along the rolling direction. [Copyright &y& Elsevier]