Search

The modification of magnesium implants with functional organic molecules is important for increasing the biological acceptance and for reducing the corrosion rate of the implant. In this work, we evaluated by a combined experimental and theoretical approach the adsorption strength and geometry of a functional self-assembled monolayer (SAM) of hydrolyzed (3-aminopropyl)triethoxysilane (APTES) molecules on a model magnesium implant surface. In time-of-flight secondary ion mass spectrometry (ToF-SIMS) and X-ray photoelectron spectroscopy (XPS), only a minor amount of reverse attachment was observed. Substrate-O-Si signals could be detected, as well as other characteristic APTES fragments. The stability of the SAM upon heating in UHV was investigated additionally. Density-functional theory (DFT) calculations were used to explore the preferred binding mode and the most favorable binding configuration of the hydrolyzed APTES molecules on the hydroxylated magnesium substrate. Attachment of the molecules via hydrogen bonding or covalent bond formation via single or multiple condensation reactions were considered. The impact of the experimental conditions and the water concentration in the solvent on the thermodynamic stability of possible APTES binding modes is analyzed as a function of the water chemical potential of the environment. Finally, the influence of van der Waals contributions to the adsorption energy will be discussed.

The influence of bovine serum albumin (BSA) on the electrochemical behaviour of pure Mg and Fe was studied in simulated body fluid (SBF), in view of the possible application of these materials as biodegradable metals. Results indicate a different trend for the BSA-effect on corrosion for the two metals: for Mg, a strong corrosion-inhibiting effect is observed in the presence of BSA in solution, especially for short-term exposure, whereas for Fe only a slight acceleration of corrosion is caused by the addition of BSA to the solution. For both metals, the protein-effect on the electrochemical behaviour shows a complex time-dependence. Surface analysis indicates that stronger BSA adsorption takes place on Mg than on Fe. Moreover, adsorption experiments with BSA and a second protein (lysozyme) were conducted. The results are discussed in view of electrostatic interactions between differently charged metal oxide/hydroxide surfaces and proteins.

As magnesium is a non-toxic and biodegradable metal, it is gaining more and more interest in the biomedical sector. The biodegradability is due to the corrosion of Mg in aqueous, chloride containing environment, as it is present in the body. However, corrosion of pure magnesium occurs too fast and takes place inhomogeneously on the metal surface. Moreover, Mg dissolution is connected with strong hydrogen evolution. Therefore alloying and/or coating of magnesium seem to be promising approaches to slow down corrosion and in return hydrogen evolution. This study explores coating of Mg with albumin via three different linker molecules, aminopropyl-triethoxysilane (APTES) plus ascorbic acid (VitC), carbonyldiimidazole (CDI) and stearic acid (SA). The metal samples were first passivated and after the pre-coating with the linker molecules the protein coating took place by soaking the pre-treated samples in an aqueous albumin solution. The immersion time was varied from 0.25 h up to 24 h. The success and the quality of the different coatings were documented by X-ray Photoelectron Spectroscopy (XPS) and Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS). Pre-coatings were additionally characterized by contact angle and surface roughness measurements. Electrochemical measurements were carried out in simulated body fluid (SBF) to characterize the coatings in view of their corrosion behavior. Albumin coatings could be produced with every linker molecule investigated. Certain protective effects were observed already for linker SAM coated Mg, overall the systems CDI-BSA and SA-BSA showed the best corrosion resistances., (Copyright © 2012 Elsevier B.V. All rights reserved.)

We present an innovative method to cover pure magnesium with protein monolayers by utilizing the OH termination of the oxide surface and silane coupling chemistry. The protein of interest was albumin. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) and X-ray photoelectron spectroscopy (XPS) were used to monitor the success of the treatment. The attachment of proteins via linker groups yielded smoother and more homogeneous surfaces than coatings produced by steeping magnesium in protein solution. A positive effect on the corrosion behavior of pure magnesium was also observed.