Search

Cement composite long-term property assessment usually is limited to the compression strain state due to the difficulty of performing long-term tests in tension and 3-point bending. This paper shows the difference in long-term properties in compression, tension, and 3-point bending for plain ordinary Portland cement mortar (OPC). The obtained results were compared to reinforced specimen results to determine whether the PVA refibres improve the long-term properties of OPC mortar in various stress-strain conditions. Cylinders, compact tension specimens (CT), and beams – plates were prepared to evaluate material properties and the role of fibre reinforcement in these different stress states. Additionally, to conventional surface-attached strain gauges, 2D-DIC was employed to observe the creep strain of specimens in tension. This paper aim to determine long-term property differences in compression, tension and 3-point bending and, also, to see if low amount PVA fibre incorporation improve long-term properties in previously stated stress-strain states. It was determined that the usage of 1 % of PVA fibres increases creep strains in compression on average by 15 % and reduced by 7 % in tension. It reduces shrinkage strain by 18 % in compression and 8 % in tension. The long-term deflection for the PVA fibre-reinforced specimens are, on average by 55 % higher than for plain OPC mortar specimens in 3-point bending.

One way to prevent cement from ending up in landfills after its shelf life is to regain its activity and reuse it as a binder. As has been discovered, milling by planetary ball mill is not effective. Grinding by collision is considered a more efficient way to refine brittle material and, in the case of cement, to regain its activity. There has been considerable research regarding the partial replacement of cement using disintegrated cement in mortar or concrete in the past few decades. This article determines and compares the creep and shrinkage properties of cement mortar specimens made from old disintegrated, old non-disintegrated, and new non-disintegrated Portland cement. The tests show that the creep strains for old disintegrated and old non-disintegrated cement mortars are close, within a 2% margin of each other. However, the creep strains for new non-disintegrated cement mortar are 30% lower. Shrinkage for old disintegrated and non-disintegrated cement mortar is 20% lower than for new non-disintegrated cement mortar. The research shows that disintegration is a viable procedure to make old cement suitable for structural application from a long-term property standpoint. Additionally, it increases cement mortar compressive strength by 49% if the cement is disintegrated together with sand. [ABSTRACT FROM AUTHOR]

Geopolymer composites have been around only for 40 years. Nowadays, they are used in buildings and infrastructures of various kinds. A geopolymer's main benefit is that it is a green material that is partially made by utilizing waste products. The carbon footprint from geopolymer matrix manufacturing is at least two times less than Portland cement manufacturing. Due to the nature of the geopolymer manufacturing process, there is a high risk of shrinkage that could develop unwanted micro-cracks that could reduce strength and create higher creep strains. Because of this concern, a common strategy to reduce long-term strains of the material, such as shrinkage and creep, is to add fiber reinforcement that would constrain crack development in the material. This article aims to determine how various kinds and amounts of different fiber reinforcement affect fly ash-based geopolymer composites' creep strains in compression. Specimen mixes were produced with 1% steel fibers, 1% polypropylene fibers, 5% polypropylene fibers, and without fibers (plain geopolymer). For creep and shrinkage testing, cylindrical specimens Ø46 × 190 mm were used. The highest creep resistance was observed in 5% polypropylene fiber specimens, followed by 1% polypropylene fiber, plain, and 1% steel fiber specimens. The highest compressive strength was observed in 1% polypropylene fiber specimens, followed by plain specimens, 1% steel fiber specimens, and 5% polypropylene fiber-reinforced specimens. The only fiber-reinforced geopolymer mix with improved long-term properties was observed with 1% polypropylene fiber inclusion, whereas other fiber-introduced mixes showed significant decreases in long-term properties. The geopolymer composite mix with 1% polypropylene fiber reinforcement showed a reduction in creep strains of 31% compared to the plain geopolymer composite. [ABSTRACT FROM AUTHOR]