Search

In this study, we investigated the effects of a crosslinking agent and a compatibilizer on the mechanical and rheological properties of waste PP and waste ground rubber tire (WGRT) composites. In order to simulate a commercial TPV, the component of waste PP and WGRT was fixed at 30 and 70 wt%, respectively. With the simple addition of SEBS-g- MA into the waste PP/WGRT composites, the tensile strength of the composite was decreased, whereas both the elongation at break and impact strength were significantly increased because of rubbery characteristics of SEBS-g-MA. In order to further improve the properties of the composites, the waste PP/WGRT/SEBS-g-MA composites was revulcanized with dicumyl peroxide (DCP). As expected, mechanical properties of the revulcanized composites was generally improved. Especially, with 15 and 1 phr of SEBS-g-MA and DCP, elongation at break was highest value of about 183% because of the recrosslinking of WGRT without chain scission of the main chain. It was found that complex viscosity of the revulcanized composite increased which might verify further vulcanization of the WGRT.

We discuss the influence of few-walled carbon nanotubes (FWCNTs) treated with nitric acid and/or sulfuric acid on field emission characteristics. FWCNTs/tetraethyl orthosilicate (TEOS) thin film field emitters were fabricated by a spray method using FWCNTs/TEOS sol one-component solution onto indium tin oxide (ITO) glass. After thermal curing, they were found tightly adhered to the ITO glass, and after an activation process by a taping method, numerous FWCNTs were aligned preferentially in the vertical direction. Pristine FWCNT/TEOS-based field emitters revealed higher current density, lower turn-on field, and a higher field enhancement factor than the oxidized FWCNTs-based field emitters. However, the unstable dispersion of pristine FWCNT in TEOS/N,N-dimethylformamide solution was not applicable to the field emitter fabrication using a spray method. Although the field emitter of nitric acid-treated FWCNT showed slightly lower field emission characteristics, this could be improved by the introduction of metal nanoparticles or resistive layer coating. Thus, we can conclude that our spray method using nitric acid-treated FWCNT could be useful for fabricating a field emitter and offers several advantages compared to previously reported techniques such as chemical vapor deposition and screen printing.

The fabrication of a flexible field-emission device (FED) using single-walled carbon nanotube (SWNT) network films as the conducting electrodes (anode and cathode) and thin multi-walled CNT/TEOS hybrid films as the emitters is reported. P-type doping with gold ions and passivation with tetraethylorthosilicate (TEOS) made the SWNT network film highly conductive and environmentally stable, and hence a good alternative to conventional indium tin oxide electrodes. CNT/TEOS hybrid emitters showed high current density, low turn-on field, and long-term emission stability, compared with CNT emitters; these characteristics can be attributed to the TEOS sol, acting both as a protective layer surrounding the nanotube tip, and as an adhesive layer enhancing the nanotube adhesion to the substrate. All-CNT-based flexible FEDs fabricated by this approach showed high flexibility in field emission characteristics and extremely bright electron emission patterns.

Polyvinylidene fluoride (PVDF)/multiwalled carbon nanotube (MWCNT) composites were prepared by using twin screw extruder at various (0–5 wt %) MWCNT loadings. Field Emission Scanning Electron Microscope (FESEM) micrographs showed a relatively good dispersion and random distribution of MWCNT in PVDF matrix. The physical and dielectric properties increased gradually with the increase in MWCNT content but the thermal stability decreased. The DSC result revealed the increase in crystallinity of the PVDF matrix. Wide angle X-Ray diffraction (WAXD) result showed a large shoulder at 2θ of 20.78° with increasing in MWCNT content. The experimental percolation threshold for the surface resistance of PVDF/MWCNT composites were estimated and clearly observed at 4 wt % of MWCNT loading. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011

A method for evaluating bulk sensitive structural characteristics of unpurified, as-purified, and acid treated single walled carbon nanotubes (SWNTs) was described in the present study. The optical spectra of SWNT solutions were well resolved after prolonged sonication and they were correlated to the diameter and the distribution of nanotubes. The acid-treated SWNTs were similar to as-purified SWNTs in terms of catalyst residue, radial breathing mode (RBM) in the Raman spectra, and the first band gap energy of semiconducting tubes in the optical spectra. The solution phase optical spectra were more sensitive to changes in the small diameter and metallic tubes after the acid treatment than were the RBM spectra.

Poly(ethylene terephthalate) (PET)/multiwalled carbon nanotube (MWCNT) composites were prepared by in situ polymerization. To improve the dispersion of MWCNTs in the PET matrix, functionalized MWCNTs having acid groups (acid-MWCNTs) and acetic groups (acetic-MWCNTs) on their surfaces were used. The functional groups were confirmed by infrared spectrometry. Scanning electron microscopy showed that acetic-MWCNTs had a better dispersion in the PET matrix than pristine MWCNTs and acid-MWCNTs. A reaction between PET and acetic-MWCNTs was confirmed by a shift of the Raman G band to a higher frequency and an increase of the complex viscosity in the rheological properties. The composites containing functionalized MWCNTs showed a large increase in their tensile strengths and moduli. The values of the strengths and moduli of the PET/acetic-MWCNT composites were higher than those of the PET/acid-MWCNT composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008

A model for flow in a Farrel Continuous Mixer based upon cylindrical coordinate hydrodynamic lubrication theory is presented. Pressure and flux fields over the rotor surface are calculated. The pumping characteristics of the various sections of the machine rotors were calculated. Generally Farrel Continuous Mixers are operated under starved conditions. Calculations are presented for continuous mixers operating under starved conditions. Pressure and fill factor profiles are determined. Fill factors are predicted to be increased by increasing throughput, increasing exit gate pressure and reducing screw speed.

Since the first discovery of carbon nanotubes (CNTs) in 1991, CNTs have generated enormous research activities in many areas of science and engineering due to their combined exceptional mechanical, thermal and electronic properties. These properties make nanotubes ideal, not only for a wide range of applications but also as a test-bed for fundamental scientific studies (Baughman et al., 2002). They can be described as a graphite sheet rolled up into a nanoscale tube. Two structural forms of CNTs exist: single-walled (SWCNTs) and multi-walled (MWCNTs) nanotubes. CNT lengths can be as short as a few hundred nanometers or as long as several micrometers. SWCNT have diameters between 1 and 10 nm and normally capped ends. In contrast, MWCNT diameters range from 5 to a few hundred nanometers because their structure consists of many concentric cylinders held together by van der Waals forces. CNTs are synthesized in a variety of ways, such as arc discharge, laser ablation, high pressure carbon monoxide (HiPCO), and chemical vapor deposition (CVD) (Dresselhaus, 1997). CNTs exhibit excellent mechanical, electrical, thermal and magnetic properties. The exact magnitudes of these properties depend on the diameter and chirality of the nanotubes and whether their structure is singleor multi-walled. Fig. 1 shows a segment of a single graphene plane that can be transformed into a carbon nanotube by rolling up into a cylinder. To describe this structure, a chiral vector is defined as OA = na1 + ma2, where a1 and a2 are unit vectors for the hexagonal lattice of the graphene sheet, n and m are integers, along with a chiral angle θ, which is the angle of the chiral vector with respect to the x direction. Using this (n, m) scheme, the three types of nanotubes are characterized. If n = m, the nanotubes are called ‘‘armchair”. If m = 0, the nanotubes are called ‘‘zigzag”. Otherwise, they are called ‘‘chiral”. The chirality of nanotubes has significant impact on their transport properties, particularly the electronic properties. For a given (n, m) nanotube, if (2n + m) is a multiple of 3, then the nanotube is metallic, otherwise the nanotube is a semiconductor. Each MWCNT contains a multi-layer of graphene, and each layer can have different chiralities, so the prediction of its physical properties is more complicated than that of SWCNT (Jin & Yuan, 2003).

Multi-walled carbon nanotubes (MWCNTs) filled polypropylene (PP) composites were prepared by a corotating intermeshing twin screw extruder. To improve the dispersion of MWCNTs, the surface of MWCNT was modified with 1,10-diaminodecane, and maleic anhydride grafted polypropylene (MA-g-PP) was used as a compatibilizer. Micrographs of well dispersed functionalized MWCNTs (diamine-MWCNT) were observed due to the reaction between MA-g-PP and diamine-MWCNT in PP/MA-g-PP/diamine-MWCNTs composites. The different behaviors in crystallization and melting temperatures of PP/MA-g-PP/diamine-MWCNTs composite were observed compared to PP and PP/neat-MWCNT. Especially, the decomposition temperature of the composite was increased by 50°C compared to PP. PP/MA-g-PP/diamine-MWCNTs composite showed the highest complex viscosity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009