Search

Stall flutter of long blades influences the operation safety of the large steam turbines in off-design conditions. As angles of attack are typically high, a partial or complete separation of the flow from the blade surface occurs. The prediction of stall flutter of turbine blades is a crucial task in the design and development of modern turbomachinery units and reliable design tools are necessary. In this work, aerodynamic stability of a linear turbine blade cascade is tested experimentally at high angle of attack +15°, Ma = 0.2 and the reduced frequency of 0.38. Controlled flutter testing has been performed in a travelling wave mode approach for the torsion with the motion amplitude of 0.5°. In addition, ANSYS CFX with SST k-ω turbulent model is used for URANS simulations of a full-scale computational domain. A separation bubble formed on suction surface near the leading edge has been found in CFD results for each blade. Excellent agreement between the experimental and numerical results in stability maps has been achieved for this case under investigation. This is encouraging and both experimental and numerical techniques will be tested further.

In order to eliminate occurrences of flutter of low pressure turbine blades it is necessary to understand the associated unsteady aerodynamics. For this reason, an experimental and numerical study of controlled flutter (travelling wave mode) in a linear turbine blade cascade oscillating in a torsional as well as translation motion is conducted. Unsteady aerodynamic forces and moments were measured on a subsonic eight-blade turbine cascade rig where central four blades are flexibly mounted each with two degrees of freedom. Thin blades in the cascade represent the tip section of the last stage rotor blades, which defines the turbine overall performance. A commercially available 3D CFD software ANSYS CFX is used to simulate the unsteady aerodynamic loading in the blade cascade. Experimental data and simulations are compared and influence of aerodynamic forces and moments on flutter is analysed.

In low-pressure steam turbines, aerodynamic and structural design of the last stage blades is critical in determining the power plant efficiency. The development of longer last stage blades which are recently over 1 meter in length is an important task for steam turbine manufactures. The design process involves a flutter analysis of last stage blade tip sections where increased unsteady aerodynamic forces and moments might endanger the blade aerodynamic stability. However, numerical design tools must be validated using measurements in test facilities under various operating conditions. In this work, ANSYS CFX is used for flutter prediction of turbine blade tip sections oscillating in a travelling wave mode. Simulations are compared to experimental results obtained from controlled flutter tests in a wind tunnel with a linear cascade of eight turbine blade profiles made of carbon fibre. Central four blades are flexibly mounted each with two degrees of freedom (i.e. bending and torsion motions). Large deflections of thin blade profiles are accounted for the estimation of unsteady aerodynamic forces and moments. A satisfactory agreement between the simulations and experiments is achieved.

Design of a new generation of the large power steam turbines leads to very long last rotor blades with tip sections operating often in supersonic region. The flow field in such tip sections is not fully explored and it is believed to be fairly complex and very sensitive even on minute changes of flow parameters. This stimulated the study of the performance of profiles suitable for rotor tip sections. Numerical simulations have been carried out using TU Prague’s code based on the solution of the RANS equations and SST turbulence model by implicit finite volume method with AUSMPW+ scheme in high resolution formulation. Experimental data have been gathered in the intermittent high-speed wind tunnel of IT CAS CR for 2D cascade measurements equipped by an adjustable supersonic inlet nozzle, perforated inserts at side walls and adjustable perforated tailboard.

Recent trends in the electric energy market such as biomass, waste incineration or combined cycle power plants require innovative solutions in steam turbine design. Variable operating conditions cause significant changes in flow field surrounding the steam turbine last stage blades. Therefore, the enlargement of operating range for last stage blades presents new challenges in design of turbine cascades. Several turbine cascades were designed and analyzed by commercial and in-house software of CTU Prague. Selected profiles were experimentally validated in the high-speed wind tunnel for 2D cascade measurements of the Institute of Thermomechanics of the Czech Academy of Sciences which is equipped by an adjustable supersonic inlet nozzle, perforated inserts at side walls and adjustable perforated tailboard. Comparisons are presented of numerical results with optical and pneumatic measurements for a wide range of inlet and outlet Mach numbers for optimized hub and tip profile cascades.

Last stage blades are a key element of steam turbines and in many ways determine the turbine configuration alongside with the overall turbine performance. The total efficiency of the low pressure turbine section can be increased by extending the last stage blades. The design process of such long blades involves a flutter analysis using CFD tools which have to be validated by measurements in test facilities under various operating conditions. Experimental data obtained from a subsonic wind tunnel with an oscillating turbine blade cascade, which is available at the Department of Power System Engineering at the University of West Bohemia, was compared with simulations in ANSYS CFX currently used in the Doosan Škoda Power. The paper provides a brief summary of experimental rig description, CFD tool setup and the results for the case of a travelling wave mode with the pure torsion motion of amplitude of 0.5°, Ma = 0.2, reduced frequency of 0.38 and angle of attack +5°.