Search

Background: Holmium:yttrium aluminum garnet laser (Ho:YAG) is still considered the gold standard in laser lithotripsy. There is a large body of literature comparing the capabilities of Ho:YAG and thulium fiber lasers (TFLs). The novel, pulsed thulium:yttrium aluminum garnet laser (p-Tm:YAG) evaluation model has only been compared with Ho:YAG in terms of its dusting performance to date. It was this study's aim to compare the p-Tm:YAG's dusting efficiency with that of a chopped TFL. Materials and Methods: During the laser ablation procedure, while the laser device was emitting light, the laser fiber was spiraled across the surface of a uniform kidney stone model via software. We relied on the stone model's difference in weight before and after the dusting procedure to assess the dusting efficiency and assessed each laser device's dusting efficiency at various preset laser configurations and laser fiber-motion speeds. We compared both laser devices' laser configurations, which were identical in pulse energy and frequency, while keeping in mind that the pulse duration differed significantly. In addition, we tested each laser device's capability. Results: The average ablated weight across all laser configurations was 0.61 g (standard deviation [SD] = 0.44 g) for p-Tm:YAG and 0.76 g (SD = 0.51 g) for TFL. After statistical analysis, we found no significant difference in ablated weight between the laser devices (U = 1715.5, p-value = 0.11). The maximum permissible frequency configuration for TFL was 1600 Hz, which resulted in the worst overall dusting output. Conclusions: We observed that the p-Tm:YAG's dusting efficiency resembled that of TFL in the identical pulse energy and frequency laser configurations. The ablation efficiency did not seem to be affected by the laser devices' differences in pulse duration. Slower laser fiber-motion speeds resulted in more efficient ablation. When using the maximum preset frequency and power configuration, TFL's dusting efficiency appeared to be inefficient.

Purpose The aim of this study was to compare the enucleation performances of four different types of laser devices in an ex-vivo experiment: a novel, pulsed Tm:YAG solid-state laser evaluation model (p-Tm:YAG), chopped thulium fibre laser (TFL), low-power Ho:YAG laser (LP-Ho:YAG), and a high-power Ho:YAG laser (HP-Ho:YAG). Methods Our primary aim was to endoscopically separate the fascial layers of a porcine belly using laser fibres within a time period of 60 s. The size of a “tissue pocket” was assessed numerically. The enucleation characteristics reflecting the surgeon’s experience were evaluated via the NASA Task Load Index (TLX) questionnaire and a questionnaire based on Likert scale. Results HP-Ho:YAG achieved with the available laser settings the largest overall “tissue pocket” (31.5 cm2) followed by p-Tm:YAG (15 cm2), TFL (12 cm2), and LP-Ho:YAG (6 cm2). The coagulation performances of p-Tm:YAG and TFL were rated the best. In the performance evaluation by the Likert questionnaire, HP-Ho:YAG (average score of 4.06) was rated highest, followed by p-Tm:YAG (3.94), TFL (3.38), and LP-Ho:YAG (3.25). The evaluation of the NASA-TLX performance questionnaire revealed average scores for HP-Ho:YAG, LP-Ho:YAG, TFL and p-Tm:YAG of 4.38, 4.09, 3.92 and 3.90, respectively. Conclusion We are the first to compare different laser devices and settings in an ex-vivo study. We found that the surgeons were most satisfied with the HP-Ho:YAG laser device, followed by the p-Tm:YAG. These findings could be highly relevant for future research and for the practical utilisation of laser systems in endourology.

In industrial manufacturing of bright steel rods, one important quality factor is the straightness or straightness deviation. Depending on the application, deviations of less than 0.1 mm per meter rod length are desired and can be reached with state-of-the-art manufacturing equipment. Such high-quality requirements can only be guaranteed with continuous quality control. Manual straightness measurements conducted offline using a dial gauge provide accurate results on single positions of the rod. We propose a contactless, optical measurement technique based on laser scanning which has the potential to be used inline during production to inspect all rods over the entire length. Only for calibration of the system the rod needs to be turned around its axis. For the measurement of straightness deviation, it is not required to turn the rod. The method is based on evaluating the intensity signal of the reflected laser radiation against the scan angle. It is shown that in combination with an accurate calibration, this signal can be used to determine the rod’s deviation from a straight rod. We explain the measurement and calibration principle as well as data evaluation. We present the experimental setup and first measurement results on a single position on several samples. For a homogeneous sample surface and neglecting laser drift, accuracy and precision were determined to be in the range of 10–20 μm. We discuss the working principle of a potential inline system.