Search

Fragmented cytokeratin 18 (fCK18) released from epithelial cells undergoing apoptosis is widely studied in various diseases. However, fCK18 measurement is not utilized in clinical practice due to imprecise disease-state cutoff values. Therefore, we set out to generate new monoclonal antibodies (mAbs) and a recombinant fCK18 (rfCK18) calibrator in an effort to develop a highly sensitive chemiluminescent enzyme immunoassay (CLEIA). New capture mAb (K18-624) had a high binding ability compared to the current commercial antibody. New detection mAb (K18-328) recognized 323S-340G of CK18. A rfCK18 was expressed in the soluble fraction of E. coli when the N-terminal region (260 amino acid residues) of CK18 was truncated. Analysis of performance and measurement of human fCK18 were evaluated using K18-624 and K18-328 in a highly sensitive CLEIA. The coefficients of variation (CV) for within-run and between-day repeatability were below 10% and the recoveries were in the range of 15%. The detection sensitivity was 0.056 ng/mL. Serum fCK18 levels were significantly increased in non-alcoholic steatohepatitis (NASH) patients when compared to healthy individuals. Our new fCK18 mAbs showed high affinity and sensitivity. CLEIA using our new antibodies will be useful in measuring fCK18 in human blood thereby generating accurate clinical diagnoses of human liver diseases.

Improving current injection into r- and m-planes of nanowires (NWs) is essential to realizing efficient GaInN/GaN multiple quantum shell (MQS) NW-based light-emitting diodes (LEDs). Here, we present the effects of different p-GaN shell growth conditions on the emission characteristics of MQS NW-LEDs. Firstly, a comparison between cathodoluminescence (CL) and electroluminescence (EL) spectra indicates that the emission in NW-LEDs originates from the top region of the NWs. By growing thick p-GaN shells, the variable emission peak at around 600 nm and degradation of the light output of the NW-LEDs are elaborated, which is attributable to the localization of current in the c-plane region with various In-rich clusters and deep-level defects. Utilizing a high growth rate of p-GaN shell, an increased r-plane and a reduced c-plane region promote the deposition of indium tin oxide layer over the entire NW. Therefore, the current is effectively injected into both the r- and m-planes of the NW structures. Consequently, the light output and EL peak intensity of the NW-LEDs are enhanced by factors of 4.3 and 13.8, respectively, under an injection current of 100 mA. Furthermore, scanning transmission electron microscope images demonstrate the suppression of dislocations, triangular defects, and stacking faults at the apex of the p-GaN shell with a high growth rate. Therefore, localization of current injection in nonradiative recombination centers near the c-plane was also inhibited. Our results emphasize the possibility of realizing high efficacy in NW-LEDs via optimal p-GaN shell growth conditions, which is quite promising for application in the long-wavelength region.

GaInN/GaN multiple quantum shells (MQS) nanowires and p-GaN shells were embedded with n-GaN layers through tunnel junction (TJ) shells using metalorganic chemical vapor deposition (MOCVD) method. The MQS nanowires were selectively grown on n-GaN/sapphire or GaN substrates. The fabrication process of laser structures with different resonators of 600500, 750, 1000 μm, and cavity widths of 7, 12, and 17 μm were investigated with insulating layer on the sidewalls of the ridge. The structures of the fabricated devices were characterized by scanning electron microscope (SEM) and current-voltage-light output characteristics were evaluated. Two different methods for mirror formation, etching and cleavage, were developed for the laser devices. During the investigation, a superior mirror formation suffered from the difference in etching rate between GaInN and GaN, generating concaves in the MQS region. Bluegreen light emission was observed from the entire ridge surface of the MQS index-guided laser structures. A maximum current density of emission at 17.9 kA/cm2 has been confirmed in the devices. The electroluminescence and cathodoluminescence measurements demonstrated that the r-plane and c-plane at the top of the MQS are dominant at low current densities, and the m-plane emission becomes stronger as the current density increases.

To achieve both the reduction of threading dislocation density (TDD) and the enhancement of light extraction efficiency (LEE) of light-emitting diodes (LEDs), a two-directional stripe-patterned sapphire substrate (TPSS) was fabricated. First, a stripe pattern parallel to the a-axis of Al2O3 was formed on an as-received c -sapphire wafer and then a second stripe pattern rotated around 3° from the m-axis of Al2O3 was formed on the first stripe PSS. The light output power of TPSS LEDs was around 1.25 times higher than that of LEDs on a flat sapphire substrate. This enhancement is caused by the increase of both the internal quantum efficiency (IQE) and the LEE. On the other hand, although the LED on TPSS with the second stripe just parallel to the m-axis of Al2O3 showed a similar enhancement ratio of the light output power, the current leakage of this LED increased with the concentration of threading dislocations on the surface of LEDs. Stripes rotated 3° from the m-axis of Al2O3 changed the growth mode and realized GaN films with a smooth surface without pit formation. Therefore, the misalignment of the stripe from the m-axis of Al2O3 will become a new design parameter for realizing high-efficiency reliable LEDs. (© 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim)

Low-temperature-deposited (LT-) AlN layers and the initial growth of GaN on a- and c-sapphire have been investigated and compared. The as-deposited LT-AlN layers on both a- and c-sapphire are composed of high-density islands. By annealing, the islands become large. The density of islands on a- and c-sapphire are 5.6 × 1010 and 7.9 × 1010 cm-2, respectively, indicating that the evolution of the solid phase epitaxy of AlN islands induced by annealing is different on a- and c-sapphire. The moire spacings obtained by plan-view electron microscopy reveal that the strain of the AlN islands on a-sapphire is larger than that of islands on c-sapphire. These results imply that development of the solid phase epitaxy is influenced by the strain. The coalescence of GaN islands grown on a-sapphire, which has larger AlN islands, is advanced compared with that of islands on c-sapphire. The relationship between the annealed AlN island density and the threading dislocation (TD) density in the GaN films is investigated on a- and c-sapphire. The TD density of the GaN films is small when the density of annealed AlN islands is low. These results indicate that decreasing the island density of the annealed AlN layers is essential for improving the crystalline quality of GaN films. It is therefore important to control the solid phase epitaxy of LT-AlN layers by annealing. (© 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim)

The fabrication of a blue m-plane GaInN light emitting diode (LED) grown on an m-plane GaN layer grown on a 3-in. patterned sapphire substrate is reported. The output power of the LED was approximately 3 mW at the wavelength of 461 nm, a driving current of 20 mA, and a forward voltage of 3.5 V. This is the first report of nonpolar or semipolar blue LEDs grown on hetero-substrates with milliwatt scale output power.