Search

Modern diesel engine aftertreatment systems require elevated temperatures for effective reduction of engine-out emissions. Maintaining elevated aftertreatment temperatures in a fuel-efficient manner is a challenge, especially at low-load engine operation where engine-outlet temperatures are low; therefore, higher engine-outlet temperatures are typically achieved via increased fuel consumption. Previous studies have demonstrated that strategies such as cylinder deactivation (method where there is neither valve motion nor fuel injection in a subset of cylinders, thereby isolating the deactivated cylinders from the gas exchange process) and cylinder cutout (method where there is no fuel injection in a subset of cylinders, implemented with high recirculated gas rates) reduce fuel consumption while elevating engine-outlet temperatures, by reducing the overall airflow through the engine. This article introduces and characterizes “non-fired cylinder ventilation” as alternate means to achieve fuel-efficient aftertreatment thermal management, by reduction of overall airflow through the engine. Fuel injection is deactivated from a subset of cylinders during non-fired cylinder ventilation, and the non-firing cylinders participate in the gas exchange process with the same manifold at a time, thereby reducing the intake-to-exhaust manifold gas exchange through the cylinders. It is demonstrated that non-fired cylinder ventilation shows similar fuel efficiency and thermal management as cylinder deactivation when the valves of the non-firing ventilated cylinders are open by at least 4 mm, due to similar, negligible, gas-exchange losses, while non-fired cylinder ventilation with lower valve lifts enables elevated engine-outlet temperatures with relatively higher fuel consumption than cylinder deactivation. Non-fired cylinder ventilation strategies demonstrate 75 °C higher temperatures at fuel-neutral conditions, and up to 35% fuel savings at similar temperatures, compared to six-cylinder operation.

Fuel-efficient aftertreatment thermal management in modern diesel engines is a difficult challenge, especially during low-load operation. This study explores the performance of cylinder deactivation in a diesel engine during low-load operation following highway cruise through experimental evaluation of two drive cycles, specifically extended idle and repeated heavy heavy-duty diesel truck creep cycles. Cylinder deactivation operations are shown to maintain comparable aftertreatment thermal management performance to conventional thermal management operation while reducing fuel up to 40% during extended idle operation. This fuel efficiency improvement coincides with engine-out emission reductions of 72% for soot and 52% for NOx. Cylinder deactivation also shows improved thermal management compared to a more fuel-efficient conventional operation.

This paper outlines a novel sensor selection and observer design algorithm for linear time-invariant systems with both process and measurement noise based on H2 optimization to optimize the tradeoff between the observer error and the number of required sensors. The optimization problem is relaxed to a sequence of convex optimization problems that minimize the cost function consisting of the H2 norm of the observer error and the weighted l1 norm of the observer gain. An LMI formulation allows for efficient solution via semi-definite programing. The approach is applied here, for the first time, to a turbo-charged spark-ignited engine using exhaust gas circulation to determine the optimal sensor sets for real-time intake manifold burnt gas mass fraction estimation. Simulation with the candidate estimator embedded in a high fidelity engine GT-Power model demonstrates that the optimal sensor sets selected using this algorithm have the best H2 estimation performance. Sensor redundancy is also analyzed based on the algorithm results. This algorithm is applicable for any type of modern internal combustion engines to reduce system design time and experimental efforts typically required for selecting optimal sensor sets.

Cylinder deactivation has been recently demonstrated to have fuel savings and aftertreatment thermal management benefits at low to moderate loads compared to conventional operation in diesel engines. This study discusses dynamic cylinder activation as an effective variant to fixed diesel engine cylinder deactivation. The set of inactive and active cylinders varies on a cycle-by-cycle basis during dynamic cylinder activation. This enables greater control over forcing frequencies of the engine, thereby allowing the engine to operate away from the drivetrain resonant frequency at all engine speeds, while maintaining similar fuel savings, thermal management, and emission characteristics as fixed cylinder deactivation. Additional benefits of dynamic cylinder activation include a reduction in the consecutive number of cycles a given cylinder is deactivated, and more even cylinder usage. Enablement of engine operation without exciting drivetrain resonant frequencies at similar fuel efficiency and emissions as fixed cylinder deactivation makes dynamic cylinder activation a strong candidate to augment the benefits already demonstrated for fixed cylinder deactivation.

Approximately 30% of the fuel consumed during typical heavy-duty vehicle operation occurs at elevated speeds with low-to-moderate loads below 6.5 bar brake mean effective pressure. The fuel economy and aftertreatment thermal management of the engine at these conditions can be improved using conventional means as well as cylinder deactivation and intake valve closure modulation. Airflow reductions result in higher exhaust gas temperatures, which are beneficial for aftertreatment thermal management, and reduced pumping work, which improves fuel efficiency. Airflow reductions can be achieved through a reduction of displaced cylinder volume by using cylinder deactivation and through reduction of volumetric efficiency by using intake valve closure modulation. This paper shows that, depending on load, cylinder deactivation and intake valve closure modulation can be used to reduce the fuel consumption between 5% and 25%, increase the rate of warm-up of aftertreatment, maintain higher temperatures, or achieve active diesel particulate filter regeneration without requiring dosing of the diesel oxidation catalyst.

Cylinder deactivation can be implemented at low loads in diesel engines to improve efficiency and aftertreatment thermal management through reductions in pumping work and airflow, respectively. The rate of increase of torque/power during diesel engine transients is limited by the engine’s ability to increase the airflow quickly enough to allow sufficient fuel addition to meet the desired torque/power. The reduced airflow during cylinder deactivation needs to be managed properly so as to not slow the torque/power response. This paper demonstrates that it is possible to operate a diesel engine at low loads in cylinder deactivation without compromising its transient torque/power capabilities, a key finding in enabling the practical implementation of cylinder deactivation in diesel engines.

Diesel engine cylinder deactivation (CDA) has been demonstrated to provide significant efficiency and aftertreatment thermal management benefits, enabling fuel-efficient emissions reduction from modern diesel engines at low load engine operation. Dynamic cylinder activation (DCA), a variant of CDA where the set of deactivated cylinders varies on a cycle-by-cycle basis, has been demonstrated to enable greater control over driveline torsional vibration while maintaining the fuel efficiency and thermal management benefits shown by fixed CDA via appropriate design of firing patterns. A model-based algorithmic approach to designing firing patterns during DCA – to control driveline torsional vibration in a user-defined frequency range, given firing density, engine speed, and maximum length of firing pattern – is described in this article. The described algorithm is generalizable to any engine configuration including different piston–cylinder layouts and number of cylinders. The algorithm is extended to design firing patterns for constrained DCA operation when CDA hardware is installed on a subset of cylinders of the engine. The resulting optimal firing patterns using the algorithm, for various combinations of inputs, are presented through an experimentally-validated simulation framework and discussed. It is demonstrated that the weighted phase-angle approach can accurately predict the frequencies and relative amplitudes of the vibration content, and, if theoretically possible, the proposed algorithm determines firing patterns that meet the specified requirements. The presented algorithm can be easily extended in future work for simultaneous selection of firing density and firing pattern during online, real-time implementation during both steady-state and transient operating conditions.