Search

In this paper, a bi-stable piezoelectric energy harvester based on the bi-stable hybrid composite laminate with a new stacking sequence design is proposed. The new stacking sequence enables this bi-stable energy harvester to have some unique features, such as uniform strains of piezoelectric elements and symmetric stable configurations. Meanwhile, the new stacking sequence design enhances the room to adjust its natural frequency such that this proposed harvester allows for adjusting to lower frequency range and increasing the inertia by a tip mass to lower the demand of excitation level in comparison to previous settings. A finite element analysis is developed to investigate the static and dynamic characteristics of this new bi-stable energy harvester. A simple numerical model with a modified version of the Duffing equation is developed based on the unique nonlinear restoring force obtained from finite element analysis to describe the fundamental response characteristics of this nonlinear bi-stable energy harvester. Numerical simulations and experiments are carried out at different harmonic excitation levels ranging from 10 to 40 Hz. The results verify that the proposed model can reasonably capture the dynamic characteristics of this broadband bi-stable energy harvester. The output powers were measured under different vibration patterns. Maximum power of 31.1 mW was generated under large-amplitude and high-energy orbits cross-well vibration pattern at an excitation frequency of 22 Hz and acceleration of 3 g ( g  = 9.8 m/s 2 ). [ABSTRACT FROM AUTHOR]

A bi-stable piezoelectric energy harvester (BPEH) based on bi-stable hybrid symmetric laminate (BHSL) is proposed for energy harvesting. Due to its large deformation and low actuation, BPEH has better energy harvesting performance at low frequencies compared with traditional resonance cantilever-type energy harvester. Two types of stacking sequence and two types of piezoelectric ceramics (PZT) shapes with identical area were considered, and four types of BPEHs were designed. The stable configurations of the BPEHs and the stress states of PZT bonded on the surface of the BSHL were simulated and analyzed by finite element analysis. In addition, the four types of BPEHs were fabricated and experimentally evaluated. The BPEHs were actuated by hand shaking to transition between the two stable configurations. Using this method, the voltage outputs and power outputs were measured at two frequencies (2 Hz and 5 Hz). The results demonstrate that the BPEHs exhibited high output power because the PZTs on their surface were fully utilized due to their double curved shape and uniform deformations. The generated powers from the BPEHs were significantly higher than that observed from a similar sized cantilever-type piezoelectric harvester. Simultaneously, the influences of stacking sequence and shape of PZT on the energy harvesting performance were evaluated. The BPEHs with the second stacking sequence generated higher power than those of first stacking sequence, and the rectangular PZT performed better compared to the square. The measured maximum power output generated by the BPEH with the second stacking sequence and rectangular PZT was 37 mW at 5 Hz. [ABSTRACT FROM AUTHOR]

Abstract: This paper presents a bistable twisting CFRP-metal hybrid laminate which has an external isotropic metallic layer. Different from the pure unsymmetric CFRP laminate and the hybrid unsymmetric laminate with an inner metallic layer, the laminate presented can be transformed from one negative curvature to another negative curvature instead of from one negative curvature to another positive curvature. Their room temperature shapes can be a unique paraboloid shape, a twisted cylindrical shape, or a twisted cylindrical shape that can be snapped through to another twisted cylindrical shape. The cured shape of the hybrid laminate is studied using analytical, finite element and experimental techniques. The investigation is focused on the hybrid laminate with lay-up of [0/90/metal]T, and shows that the principal direction of cured curvature is 45°. The predicted cured shape and the snap-through loads agree well with experimental results. [Copyright &y& Elsevier]

Abstract: This paper develops a multi-stable lattice structure consisting of tri-stable lattice cell which is made by bistable laminates. The multi-stable lattice structure with N tri-stable lattice cells, which can exhibit 2 N stable states, is successfully designed and fabricated. The critical loads snapping lattice structure are investigated by the experimental and finite element techniques. The method to simulate the behaviors of contact and constraint between the neighboring bistable laminates are presented. The snap through process of multi-stable lattice structures among multiple states are numerically simulated and experimentally validated. The multiple stabilities highlight the potential to achieve a smooth shape variation in the large area multi-stable structures. [Copyright &y& Elsevier]

Abstract: This paper presents a new heating actuation method to induce the snap-through phenomenon of bi-stable laminates by manipulating the residual stress in laminates. The mechanism of the heating actuation method is analyzed, and the snap-through process is simulated by the finite element method. The heating actuation experiments on two types of laminates with different stacking sequences are performed. Good agreement is obtained between the experimental data and the finite element analysis (FEA). Subsequently, the heating actuation method is applied to several different bi-stable laminates and investigated by FEA. The FEA results show that this heating actuation method is an effective way to induce the snap-through phenomenon of bi-stable laminates of different thicknesses, sizes and shapes. [Copyright &y& Elsevier]

Bi-stable composite laminates with piezoelectric transducers have been shown to capture energy over a wide frequency range and deliver significantly greater energy than resonant devices. In this work, the influence of lay-up design on the performance of bi-stable piezoelectric energy harvester (BPEH) based on bi-stable hybrid symmetric laminate (BHSL) is analyzed and verified. The initial voltage induced by stable configuration and longitudinal curvature of BPEH with different lay-up and hybrid width were calculated and analyzed by a static finite element analysis. The lay-up can vary initial voltage and longitudinal in opposite directions, and hybrid width can adjust these two variables in the same direction. The strain variations of piezoelectric transducer between two stable configurations were also analyzed. The initial voltage of BPEH depends on strain variations in the two directions. And then the finite element results are verified by experiment. Three types of BPEH were manufactured and actuated by two methods to measure their output powers. These BPEHs presented different dynamic responses, and the output powers under different vibration modes were measured. The highest output power of BPEH in this work is 42.2 mW and the highest power density is 78.1 mW/cm 3 . [ABSTRACT FROM AUTHOR]

Bistable composite laminates have the potential advantage in the fields of wind energy harvesting and deformable wings, which involve many fluid–structure interaction issues. This paper presents the fluid–structure interaction analysis of a cantilevered bistable hybrid symmetrical laminate (BHSL) in the uniform wind. In this work, a finite element model based on the Lattice Boltzmann Method (LBM) is used to analyze the wind-induced response of the BHSL and its variations with respect to wind speed and laminate length. Then, the wind-induced vibration behavior of BHSL is verified by wind tunnel tests. The finite element analysis (FEA) results are in good agreement with the experimental results. The results show that as the wind speed increases, the BHSL transitions from a single-well vibration response to a cross-well vibration response. The wind-induced vibration analysis of BHSL will provide analytical methods for its application in deformable wings and energy harvesting for wind-induced vibration. [ABSTRACT FROM AUTHOR]

A nonlinear device is presented for simultaneous vibration absorption and energy harvesting. This device is composed of a nonlinear energy sink and a piezoelectric energy harvester (NES-EH), and its core component is the simply-supported bi-stable piezoelectric composite laminate (BPCL). Its outstanding advantages are light weight, simple and reliable structure. The theoretical model is developed to model a harmonically excited linear oscillator coupled with NES-EH. The Runge–Kutta method and the harmonic balance method (HBM) are used to solve the theoretical model numerically and analytically. The vibration suppression efficiency is utilized to quantify the vibration absorption performance, while the energy harvesting performance is assessed by bandwidth for energy harvesting and maximum voltage within the bandwidth. The effects of the excitation amplitude, the concentrated mass of NES-EH, the length and width of BPCL, and the load resistance are considered on the performances of NES-EH. The vibration absorption and energy harvesting performances of NES-EH can be improved by adjusting these parameters. In addition, the proposed NES-EH can achieve the goal of higher power density and normalized power density under low-amplitude excitation and simultaneously have a good vibration absorption effect. Finally, approximate analytical solutions are obtained by using HBM to exhibit various bifurcations and singularities. • Simply-supported bi-stable piezoelectric composite is first used to integrate vibration absorption and energy harvesting. • NES-EH has advantages of light weight, simple and reliable structure dueto no high strength frame or external device. • Mathematical modeling is developed to forecast the performances of NES-EH. • The effects of excitation amplitude, concentrated mass of NES-EH, geometries of BPCL, and load resistance are considered. [ABSTRACT FROM AUTHOR]

The resulting oscillation of bi-stable hybrid symmetric laminate could enable broadband energy harvesting via piezoelectric transduction. The aim of this work is to investigate its dynamic behaviors to provide the basis for designing broadband energy harvester. This paper proposes the dynamic analysis of this bi-stable laminate, focusing on the intra-well dynamics around its stable states and the inter-well dynamics between two stable states. Two types of stacking sequence are performed for this bi-stable laminate, and experimental testing with different harmonic excitations is carried out for each type of this bi-stable laminate. The strain responses at three positions are monitored to investigate the dynamic responses. A finite element model is also developed to analyze the static strain distribution and capture the dynamics. The results show that the laminates exhibit intra-well response under low-level excitation, and the inter-well response at a particular range frequency appears when excitation level increases. Different types of inter-well response mode involving the snap-through behavior are obtained in experiments, such as intermittent inter-well vibration and chaotic vibration. The presented results essentially highlight the need for considering the stacking sequence associated with the dynamics while designing the hybrid bi-stable symmetric laminate to obtain the desirable nonlinear response. [ABSTRACT FROM AUTHOR]

A bi-stable device is presented for simultaneous vibration absorption and energy harvesting by introducing the piezoelectric element into the bi-stable nonlinear energy sink (BNES), which is called the bi-stable piezoelectric absorber (BPZA). BPZA only consists of the cantilever bi-stable piezoelectric composite laminate (BPCL) and tip masses. This BPZA is a lightweight, simple and reliable structure since it does not need any external devices to maintain bistability. A finite element model (FEM) and an equivalent theoretical model are developed to model a harmonically excited linear oscillator coupled with BPZA. The Runge-Kutta method is used to solve the theoretical model numerically. The effects of the excitation amplitude, the tip mass of BPZA and the load resistance are considered on the vibration suppression efficiency and energy harvesting of BPZA. The results show adjusting these parameters can improve the vibration suppression efficiency and energy harvesting of BPZA. In addition, the experimental prototype is prepared and verifies the rightness of the finite element model and theoretical model. The BPZA achieves the goal of higher power density at lower acceleration and simultaneously has a good vibration absorption effect. Maximum power of 15.8mW is generated at an excitation frequency of 22 Hz and acceleration of 0.5 g. [ABSTRACT FROM AUTHOR]

This paper presents a multistable variable cross-section laminate (MVCL), which is designed by applying the displacement constraint at the two opposing ends of the laminate. A theoretical model describing the MVCL as rigid bars connected with compliant hinges is built to predict the equilibrium configurations and snap-through loads of the MVCL. The snap-through process of the multistable structure is investigated via experiment and finite element analysis (FEA). Subsequently, the theoretical model is improved by simplifying the middle segment of the MVCL as an elastic beam. Good agreement is obtained between the experimental test, FEA, and improved theoretical model results. It is shown that the current approach can be successfully applied to predict the equilibrium configurations and snap-through loads of an MVCL. The snap-through loads can be adjusted by changing the middle segment length of an MVCL. [ABSTRACT FROM AUTHOR]

The quasi-zero-stiffness (QZS) vibration isolator is usually composed of positive and negative stiffness elements in parallel. The negative stiffness element usually requires specific constraint boundaries to form negative stiffness characteristics, which cannot meet the lightweight design of spacecraft structures. So the bi-stable hybrid symmetric laminate (BHSL) is presented as a negative stiffness element. A finite element model (FEM) is developed to carry out static and dynamic analyses of this vibration isolator. An equivalent theoretical model is developed based on the restoring force–displacement curve of BHSL. The approximate analytical solutions and direct numerical solutions are obtained by employing the averaging method and the Runge-Kutta method, respectively. Different types of the steady-state response are obtained, namely the symmetrical multi-harmonic response, the asymmetric multi-harmonic response and the single-harmonic response. There exists a small gap between the analytical solutions and the Runge-Kutta solutions or the FEM results only at the low frequency excitation due to the super-harmonics. The displacement transmissibility is used to quantify the vibration isolation performance of this vibration isolator. The experiment is designed to verify the theoretical and FEM models from static and dynamic analysis perspectives. The results show adjusting geometric parameters and lay-up designs can improve the vibration isolation performance. [ABSTRACT FROM AUTHOR]