Search

In order to increase the torque density of the five-phase machines, the third harmonic is commonly employed. In this paper, the optimal and critical ratios for the third harmonic current injection are analytically derived and validated by finite element (FE) analyses. It is found that the optimal and critical injection ratios along with the torque improvement are dependent on the ratio of the third harmonic back electromotive force to the fundamental one. In order to improve the electromagnetic torque contributed by the third harmonic component, this paper employs unequal tooth to increase both the fundamental and third harmonic winding factors. Meanwhile, the optimal unequal tooth width combination is deduced and demonstrated by the FE method. When the third harmonic current is injected under the same amplitude constraint, the output torque can be improved. When the third harmonic current is injected under the same RMS value constraint, for the ten-slot/eight-pole equal tooth machine, the output torque can barely be increased, whilst for the unequal tooth machine, the output torque can be increased by 2.1%. Finally, the ten-slot/eight-pole machine with unequal teeth is prototyped and tested to prove the analyses. [ABSTRACT FROM PUBLISHER]

The partitioned stator switched-flux permanent magnet (PM) (SFPM) (PS-SFPM) machine is a novel stator-PM machine in which PMs and armature windings are separately placed in two different stators. Compared with the conventional SFPM machine with a single stator in which both PMs and armature windings are located, the PS-SFPM machine can generate higher torque density due to the utilization of the machine's inner space. In this paper, the magnetic gearing effect in the PS-SFPM machine is investigated in terms of air-gap field harmonics based on a simple magnetomotive force (MMF)-permeance model. It is found that the PS-SFPM machine is one type of magnetically-geared machine, in which the modulations of rotor iron pieces to the open-circuit PM and armature reaction fields are similar to those found in the magnetic gear and the conventional magnetically geared machine. The pole-pair numbers and rotating speeds of the air-gap field harmonics obtained by the MMF-permeance model are verified by finite element (FE) analysis. More than 93% of the average electromagnetic torque is contributed by the main air-gap field harmonics having pole-pair numbers (2i - 1)\boldsymbol p PM and \rm| N\rm{r} \,\pm \, (2i-1)pPM| ( i = 1,2,3) in a PS-SFPM machine with pPM-pole-pair PMs and Nr-rotor-pole. A prototype machine is fabricated and tested to verify the FE analysis. [ABSTRACT FROM PUBLISHER]

In this paper, the end effects of a partitioned stator flux reversal permanent magnet (PM) machine with a surface-mounted PM (SPM) inner stator and a consequent pole PM (CPM) inner stator are comparatively analyzed. It is found that due to higher saturated inner stator steel in a CPM machine, it suffers from larger end effect than the SPM machine. Influence of armature reaction on end effect is investigated by a finite-element (FE) analysis, together with that of aspect ratio, i.e., axial stack length to stator outer diameter. Furthermore, it is found that in the CPM machine, the optimal PM arcs for the highest average electromagnetic torque predicted by 2-D and 3-D FE are different due to the variation of end effect with PM arc. Prototypes with both SPM and CPM inner stators are built and tested to verify the FE analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes a new partitioned stator flux reversal permanent magnet (PM) (PS-FRPM) machine having integer-slot overlapping windings, i.e., the slot number per pole per phase q is an integer, based on the magnetic gearing effect in stator-PM machines. Compared with the existing PS-FRPM machine with fractional-slot nonoverlapping windings, a more sinusoidal armature reaction magnetomotive force can be achieved in the proposed PS-FRPM machine with integer-slot overlapping windings, resulting in lower iron loss and PM loss. Electromagnetic performance of the PS-FRPM machine, which has q = 1 overlapping windings is analyzed and compared with PS-FRPM machine, which has q = 0.5 nonoverlapping windings by finite element (FE) analysis. FE results show that the proposed 24/10/12-outer-stator/rotor/inner-stator-pole PS-FRPM machine with q = 1 overlapping winding exhibits higher fundamental phase back-electromotive force, higher average electromagnetic torque and lower torque ripple, lower loss and higher efficiency, higher self-inductance but lower mutual inductance, higher d-axis inductance, and potential infinite flux-weakening capability compared with the 12/10/12-outer-stator/rotor/inner-stator-pole PS-FRPM machine with q = 0.5 nonoverlapping windings. Both prototype machines with q = 1 overlapping winding and q = 0.5 nonoverlapping windings are built and tested to verify the FE analyzes. [ABSTRACT FROM PUBLISHER]

This paper first investigates the flux-weakening control performance of two types of partitioned stator-switched flux permanent-magnet (PM) (PS-SFPM) machines and then proposes a novel mechanical flux-weakening technique. The PS-SFPM machine topologies, operation principles, and flux-weakening control method are described. In addition, it is shown that by mechanically varying the relative position of two stators of the PS-SFPM machine, the PM flux linkage can also be varied, and hence, it can provide improvement in the speed range and torque capability. The optimal relative mechanical angle is derived to enable the maximum torque capability and reduce or even avoid the flux-weakening current injected by the inverter. The proposed technique is verified by three-dimensional (3-D) finite-element (FE) analyses and experiments on the prototype machines. [ABSTRACT FROM AUTHOR]

This paper proposes a partitioned stator variable flux reluctance machine (PS-VFRM) in which field and armature windings are placed on two separate stators. The influence of different stator/rotor-pole combinations on the electromagnetic performance is examined using finite-element analysis. Candidate designs maximize the average electromagnetic torque. Compared against the conventional single stator VFRM, the proposed PS-VFRM is shown to provide 24.6% and 12.7% increases in torque density and efficiency, respectively. The static electromagnetic performance is validated using experimental prototypes. [ABSTRACT FROM PUBLISHER]

In this paper, a double stator (DS) wound field (WF) switched flux (SF) (DS-WFSF) machine is proposed. In the DS-WFSF machine, field and armature windings are separately placed in two different stators. Compared with the conventional WFSF machine with single stator, in which both field and armature windings are located, nonoverlapping concentrated windings and large slot areas can be obtained in the DS-WFSF machine. The proposed DS-WFSF machine exhibits >19% higher torque than the conventional WFSF machine, with both machines having the same space envelope and being globally optimized. The influence of leading design parameters, such as copper loss ratio between the field and armature windings, air-gap diameter, and rotor iron piece thickness and widths, on the average output torque is investigated for the DS-WFSF machines having 12/10, 12/11, 12/13, and 12/14 stator slots/rotor iron pieces. All the analyses are confirmed by both finite element and experimental results. [ABSTRACT FROM AUTHOR]

In this paper, novel partitioned stator doubly salient permanent magnet (PS-DSPM) machines with separated PM excitation and armature windings are proposed. Compared with conventional DSPM machines with single stator in which PMs are inserted in the yoke and windings are arranged on the teeth, the proposed PS-DSPM machine has two stators with PMs and windings located separately. Two sets of PS-DSPM machines, i.e., PS-DSPM-I and PS-DSPM-II machines, are proposed based on the conventional DSPM-I and DSPM-II machines in which the PMs are located on the stator yoke with intervals of every number of phases and every stator pole, respectively. The electromagnetic performance including back electromotive force (EMF) and torque characteristics of the proposed PS-DSPM machines are analyzed and compared with those of the conventional DSPM machines based on the optimal designs for the highest average electromagnetic torque by finite-element (FE) analysis in this paper. FE results show that the proposed PS-DSPM-I and PS-DSPM-II machines exhibit 8.49% and 207% higher torque density than the conventional DSPM-I and DSPM-II machines with same copper loss, respectively. The influence of main design parameters on the average electromagnetic torque in the proposed PS-DSPM machines is investigated, together with the conventional DSPM machines. A prototype machine of PS-DSPM-II is manufactured and tested to verify the FE analysis. [ABSTRACT FROM AUTHOR]