Search

As the focus on developing new polymer electrolytes continues to intensify in the area of alternative energy conversion and storage devices, the rational design of polyelectrolytes with high single ion transport rates has emerged as a primary strategy for enhancing device performance. Previously, we reported a series of sulfonate based copolymer ionomers based on using mixed bulky quaternary ammonium cations and sodium cations as the ionomer counterions. This led to improvements in the ionic conductivity and an apparent decoupling from the Tg of the ionomer. In this article, we have prepared a new series of ionomers based on the homopolymer of poly(2-acrylamido-2-methyl-1-propane-sulfonic acid) using differing sizes of the ammonium counter-cations. We observe a decreasing Tg with increasing the bulkiness of the quaternary ammonium cation, and an increasing degree of decoupling from Tg within these systems. Somewhat surprisingly, phase separation is observed in this homopolymer system, as evidenced from multiple impedance arcs, Raman mapping and SEM. The thermal properties, morphology and the effect of plasticizer on the transport properties in these ionomers are also presented. The addition of 10 wt% plasticizer increased the ionic conductivity between two and three orders of magnitudes leading to materials that may have applications in sodium based devices.

Addition of silica nanoparticles functionalised with lithium propane sulfonate to the organic ionic plastic crystal N-ethyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)amide ([C2mpyr][NTf2]) results in a significant increase in ionic conductivity. Analysis of these nanocomposites by impedance spectroscopy, NMR, positron annihilation lifetime spectroscopy (PALS) and Raman spectroscopy suggests that this is the result of higher matrix mobility due to an increase in defect size and concentration. The effect of these functionalised nanoparticles is compared to that previously observed for unfunctionalised nanoparticles in the lithium-doped and pure plastic crystal.

In this work lithium modified silica (Li-SiO2) nano-particles were synthesized and used as a single ion lithium conductor source in gel electrolytes. It was found that Li-SiO2 exhibited good compatibility with DMSO, DMA/EC (a mixture of N,N-dimethyl acetamide and ethylene carbonate) and the ionic liquid, N-methyl-N-propyl pyrrolidinium bis(trifluoromethylsulfonyl) amide ([C3mpyr][NTf2]). Several gel electrolytes based on Li-SiO2 were obtained. These gel electrolytes were investigated by DSC, solid state NMR, conductivity measurements and cyclic voltammetry. Conductivities as high as 10−3 S/cm at room temperature were observed in these nano-particle gel electrolytes. The results of electrochemical tests showed that some of these materials were promising for using as lithium conductive electrolytes in electrochemical devices, with high lithium cycling efficiency evident.

Zwitterionic compounds such as those based on 1-butylimidazolium-3-(n-butanesulfonate) have previously been shown to have positive effects on the transport properties of polyelectrolytes. The addition of the zwitterion has been found to, in some cases, increase the dissociation of the lithium ion and enhance the conductivity by almost an order of magnitude. In this work, we report the effects of adding the above-mentioned zwitterion into the polyelectrolyte gel system poly(lithium methacrylate-co-N,N-dimethyl acrylamide); the anionic group being a stronger base leads to different behaviour for this copolymer compared to previous work. Polyelectrolyte gels based on dimethyl sulfoxide and polyether solvents were investigated to determine the breadth of applicability of the zwitterion in improving lithium ion transport. Impedance spectroscopy and pulse field gradient-NMR diffusion indicate an increase in the number of available charge carriers with zwitterion addition in some gel systems, however, the effect is not universal.

Novel polymer electrolyte materials based on a polyelectrolyte-in-ionic-liquid principle are described. A combination of a lithium 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPSLi) and N,N′-dimethylacrylamide (DMMA) are miscible with the ionic liquid, 1-ethyl-3-methylimidazolium dicyanamide (EMIDCA). EMIDCA has remarkably high conductivity (≥ 2 · 10−2 S · cm−1) at room temperature and acts as a good solvating medium for the polyelectrolyte. At compositions of AMPSLi less than or equal to 75 mol-% in the copolymer (P(AMPSLi-co-DMAA)), the polyelectrolytes in EMIDCA are homogeneous, flexible elastomeric gel materials at 10 − 15 wt.-% of total polyelectrolyte. Conductivities higher than 8 · 10−3 S · cm−1 at 30 °C have been achieved. The effects of the monomer composition, polyelectrolyte concentration, temperature and lithium concentration on the ionic conductivity have been studied using thermal and conductivity analysis, and pulsed field gradient nuclear magnetic resonance techniques.

High conductivity in single ion conducting polymer electrolytes is still the ultimate aim for many electrochemical devices such as secondary lithium batteries. Achieving effective ion dissociation in these cases remains a challenge since the active ion tends to remain in close proximity to the backbone charge as a result of a low degree of ion dissociation. A unique aspect of this dissociation problem in polyelectrolytes is the repulsion between the backbone charges created by dissociation. One way of enhancing ion dissociation in polyelectrolyte systems is to use copolymers in which only a fraction (

In order to achieve high conductivity in a polymer electrolyte, polymer-in-ionic-liquid electrolytes have been explored. It is found in this study that poly-[vinylpyrrolidone-co-(vinyl acetate)] (P(VP-c-VA) in 1-ethyk-3-methylimidazolium bis(trifluoromethyl sulfonyl) amide (EtMeIm + Tf2N - ) and poly(N,N-dimethyl acrylamide) (PDMAA) in trimethyl butyl ammonium bis(trifluoromethane sulfonyl) amide (N + 1114 Tf 2 N - ) produce ion-conducting liquids and gels. The P(VP-c-VA)/ EtMeIm + Tf 2 N - mixture has a conductivity around 10 -3 S . cm -1 at 22°C, for copolymer concentrations up to 30 wt.-%. Thermal analysis shows that the Tg of the PVP(VP-c-VA)/ EtMeIm + Tf 2 N - system is well described by the Fox equation as a function of polymer content. Poly(methyl methacrylate) (PMMA)/ EtMeIm + Tf 2 N - gel electrolytes were prepared by in-situ polymerisation of the monomer in the ionic liquid. In the presence of 0.5 - 2.0 wt.-% of a crosslinking agent, these PMMA-based electrolytes displayed elastromeric properties and high conductivity (ca. 10 -3 S. cm -1 ) at room temperature.

Characterization of a new family of salts, based on a number of 1-alkyl-2-methyl pyrrolinium cations and the bis(trifluoromethane sulfonyl) amide anion (TFSA), is presented. From the thermal analysis, conductivity and X-ray diffraction (XRD) measurements, at least one of the compounds of the family, 1-ethyl-2-methyl pyrrolinium TFSA, was found to exhibit plastic crystal phases before melting and to exhibit high conductivity in the solid state (1×10−4 S cm−1 at 25 °C). This plastic crystal behaviour is discussed in comparison with other members of this pyrrolinium salt family.

Novel lithium polyelectrolyte–ionic liquid systems, using poly(lithium 2-acrylamido-2-methyl propanesulfonate) and its copolymer with N-vinyl formamide, have been developed in this work. The ionic liquid used in this work is from a novel family of methanesulfonate ionic liquids, specifically N-hexyl-N,N,N-tributyl ammonium methanesulfonate, which is chosen because of the similarity with the anionic functionality of the polymer. The ionic liquid thereby acts as a good solvating medium for the polyelectrolyte. It was found that the copolymer-based polyelectrolyte–ionic liquid system exhibits two to three times higher conductivity than that of the homopolymer system. The results of solid-state 7Li-NMR have shown that lithium cations in the copolymer system are mobile whereas in the homopolymer, only a fraction appears to be mobile even at 80 °C. This supports the hypothesis that separation of the charged groups on the polymer backbone via the co-monomer encourages the dissociation of lithium cations from the sulfonate groups bonded to the polymer chains, and hence, results in an increase in conductivity of the polyelectrolyte material.

The free volume behaviour of the polyacrylonitrile/lithium triflate system is investigated over the composition range 0–75 wt % salt. The addition of salt, up to 45 wt %, to the PAN polymer substantially increases the free volume as measured by the orthopositronium pickoff lifetime, τ3. Beyond this salt concentration (i.e., 45–70 wt %) the free volume remains approximately constant. This constant free volume region corresponds to a region of high ionic conductivity in the glassy state, making these materials polymer-based fast ion conductors, that is, having a decoupling ratio Rτ ≫1. The high salt content in these fast ion conductors results in a high susceptibility to polar solvents such as water. For all compositions, water absorption results in a free volume increase attributed to plasticization; however, in the fast ion conducting region, a significantly larger free volume response due to plasticization is measured and may be connected to a percolation morphology in these samples. Salt addition is shown to lower the Tg, as measured by positron annihilation lifetime spectroscopy (PALS). Tg is 115°C for PAN and 85°C for 66 wt % lithium triflate. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 341–350, 2000

Methoxy-ethylene glycol methacrylates, CH 2 CMeCOO(CH 2 CH 2 O) n Me ( n = 1, 2, 3), ethoxy-triethylene glycol methacrylate, CH 2 CMeCOO(CH 2 CH 2 O) 3 Et, and N,N-dimethylaminoethyl methacrylate, CH 2 CMeCOOCH 2 CH 2 NMe 2 , were used to synthesise the corresponding polymers. Conductivities of these polymers complexed with lithium perchlorate were investigated. Tetraethylene glycol dimethyl ether was used as plasticiser to increase the conductivity of the materials. A conductivity of 10 −5 S cm −1 was obtained at room temperature for the plasticised polymer samples. Effects of polymer structure, plasticiser, salt concentration and temperature on conductivity and glass transition temperature of the polymer electrolytes are discussed.

N,N-Dimethylpyrrolidinium hydroxide (P11OH·4H2O) was found to exhibit high ionic conductivity in the solid state (7 × 10−3 S cm−1 at 25 °C) and unusual thermal properties, and 2H solid state NMR measurements indicate liquid-like mobility of the deuterium species in the solid state of P11OD·4.5D2O.

The future of lithium metal batteries as a widespread, safe and reliable form of high-energy-density rechargeable battery depends on a significant advancement in the electrolyte material used in these devices. Molecular solvent-based electrolytes have been superceded by polymer electrolytes in some prototype devices, primarily in a drive to overcome leakage and flammability problems, but these often exhibit low ionic conductivity and prohibitively poor lithium-ion transport. To overcome this, it is necessary to encourage dissociation of the lithium ion from the anionic polymer backbone, ideally without the introduction of competing, mobile ionic species. Here we demonstrate the effect of zwitterionic compounds, where the cationic and anionic charges are immobilized on the same molecule, as extremely effective lithium ion 'dissociation enhancers'. The zwitterion produces electrolyte materials with conductivities up to seven times larger than the pure polyelectrolyte gels, a phenomenon that appears to be common to a number of different copolymer and solvent systems.

Novel protic ionic liquids (PILs) based on a tributyl phosphonium cation have been synthesised and characterised, revealing that the phosphonium based ILs show high thermal stability, high ionic conductivity and facile proton reduction compared to the corresponding ammonium based ILs.

The development of new liquid and solid state electrolytes is paramount for the advancement of electrochemical devices such as lithium batteries and solar cells. Ionic liquids have shown great promise in both these applications. Here we demonstrate the use of phosphonium cations with small alkyl chain substituents, in combination with a range of different anions, to produce a variety of new halide free ionic liquids that are fluid, conductive and with sufficient thermal stability for a range of electrochemical applications. Walden plot analysis of the new phosphonium ionic liquids shows that these can be classed as “good” ionic liquids, with low degrees of ion pairing and/or aggregation, and the lithium deposition and stripping from one of these ionic liquids has been demonstrated. Furthermore, for the first time phosphonium cations have been used to form a range of organic ionic plastic crystals. These materials can show significant ionic conductivity in the solid state and thus are of great interest as potential solid-state electrolyte materials.

Five new salts based on 1-alkyl-2-methyl pyrrolinium ion are reported, two involving the iodide ion and three involving the bis(trifluoromethanesulfonyl) amide ion. The iodide salts have melting points around 100 °C, while the amide salts have melting points around room temperature. Two of the amide salts can be easily quenched into the glassy state and exhibit glass transition temperatures around −70 °C. The 2-methyl pyrrolinium cation bears structural similarities to the aromatic imidazolium cations on one hand and the cyclic ammonium cation family based on the pyrrolidinium cation on the other. The properties of the salts reported here are compared within these two related families of salts.