Search

A beam optics study using the ITER-relevant high intense negative ion beams, such as 1 MeV, 200 A/m2, has been performed experimentally and analytically using a multi-aperture and five-stage accelerator. Initially, multi-beamlets generated from this accelerator were deflected in various directions due to the magnetic field and space charge repulsion between beams and showed various divergences. These had limited the pulse length and the beam energy. Compensation methods of the beamlet deflections have worked effectively and contributed to achieving the ITER requirement, the divergence angle of <7 mrad, and the deflection angle of <1 mrad for 1 MeV beam. The beam pulse has been gradually extended from 1 to 100 s and is now going to a longer pulse based on these results. One of the remaining issues is to understand and suppress peripheral components of the beam, namely, the halo, and to reduce the local heat loads observed around the aperture edge. This halo component has been successfully distinguished from the beam core by using a newly developed beam emittance measurement system for high intense beams. By combining this measured beam emittance and the beam simulation, it was clarified for the first time that the halo components are generated in an area of 1 mm width from the aperture edge. [ABSTRACT FROM AUTHOR]

Long pulse acceleration of hydrogen negative ion beams with the power density over 70 MW/m2 and the pulse length over 100 s has been demonstrated for the first time by using a multi-aperture 3-stage accelerator. Such long pulse acceleration was achieved by integrating the design of beam optics and voltage holding capability to meet the requirements of JT-60SA. By using the newly designed accelerator for JT-60SA, voltage holding at 500 kV with beam acceleration was stably sustained even after 5 g of cesium was seeded, and heat load on each acceleration grid was reduced below the allowable level for long pulse, less than 5% of total acceleration power. As a result, 500 keV, 154 A/m2 for 118 s beam acceleration was achieved, which satisfies the requirement of the negative ion source for JT-60SA. This pulse length of such high-power density beams is longest in the world. In addition, the result contributes to the long pulse acceleration of multi-stage electrostatic accelerators, such as 1 MeV negative ion accelerator for ITER. [ABSTRACT FROM AUTHOR]

The long-pulse acceleration of the high-power positive ion beam has been demonstrated with the JT-60 positive ion source in the joint experiment among Japan Atomic Energy Agency (JAEA), Korea Atomic Energy Research Institute (KAERI) and National Fusion Research Institute (NFRI) under the collaboration program for the development of plasma heating and current drive systems. In this joint experiment, the increase of the heat load and the breakdowns induced by the degradation of the beam optics due to the gas accumulation was one of the critical issues for the long-pulse acceleration. As a result of development of the long-pulse operation techniques of the ion source and facilities of the neutral beam test stand in KAERI, 2 MW 100 s beam has been achieved for the first time. The achieved beam performance satisfies the JT-60SA requirement which is designed to be a 1.94 MW ion beam power from an ion source corresponding to total neutral beam power of 20 MW with 24 ion sources. Therefore, it was found that the JT-60 positive ion sources were applicable in the JT-60SA neutral beam injectors. Moreover, because this ion source is planned to be a backup ion source for KSTAR, the operational region and characteristic has been clarified to apply to the KSTAR neutral beam injector. [ABSTRACT FROM AUTHOR]

Toward long-pulse productions of 22A negative ion beams for 100s in JT-60SA, the plasma generator of the negative ion source has been developed to achieve stable long-pulse generations of spatially uniform negative ions. To realize the long pulse production of the negative ions, an actively cooled plasma grid (PG) has been designed to keep a surface temperature of 250–300°C optimized for high negative ion production. The designed active cooling system has a potential to control the surface temperature of the PG to 250°C with a time constant of 10s by flowing the fluorinated fluid having the high boiling temperature of 270°C. Since the time constant is sufficiently shorter than that of the degradation of the negative ion production, the active cooling system is applicable to the long-pulse operation of the large-current negative ion source, such as JT-60SA and ITER ion sources. As for the high current beam production, spatial uniformity of the negative ion productions in the plasma generator is improved. The calculation results of the magnetically confined electron orbits emitted from filaments showed that longitudinal deviations of the primary electron distributions has been reduced from 27% to 6% by the application of the symmetric magnet arrangements, so called the tent-shaped filter. This reduction of the deviation could reduce the grid heat load, leading to the long pulse production of the negative ion beams. [ABSTRACT FROM AUTHOR]