Search

In this article, a current balancing coupled inductor (CBCL) based asymmetrically configured quad-active-bridge (QAB) converter is proposed. The QAB converter provides high-frequency isolation for a dc–dc stage of a solid state transformer (SST), as well as provides a modular solution to the SST medium-voltage (MV) dc link. The proposed CBCL ensures current balancing among/three active H-bridges without using any dedicated controller and without expensive sensors when transferring equal power from MV to low-voltage side. The proposed CBCL is the integration of three inductors of the active H-bridges required for power transfer and zero-voltage-switching and does not require an extra magnetic volume. Experimental results are presented to validate the performance. [ABSTRACT FROM AUTHOR]

An LED driver consisting of dimmable current balancing circuits (CBCs) and a boost converter with drain voltage balance (DVB) and phase-shifted pulsewidth modulation (PSPWM) control schemes is presented. To reduce the power loss on conventional linear current regulators, CBCs are employed. The DVB control scheme is proposed to maintain a desired constant voltage across the CBCs, so as to increase current balance and achieve high efficiency of the CBCs. Thus, the bus voltage of the boost converter is adaptively regulated based on the DVB control. The PSPWM control scheme can alleviate the variation of the bus current provided by the boost converter. As a result, the transient ripple of the bus voltage can be reduced when the light-emitting diode (LED) strings are turned on and off. Furthermore, the utilization of DVB control is increased when the PWM dimming duty cycle becomes lower. The experimental results demonstrate that the minimum voltage among the CBCs is always kept at the lowest constant level while maintaining the required current passing through the LED strings. The efficiency of the CBCs is kept almost the same for different LED currents and is over 95%. Thus, a high-efficient parallel-string dimmable LED driver with simple circuitry can be achieved. [ABSTRACT FROM PUBLISHER]

In this paper, a single-switch coupled-inductor-based two-channel light-emitting diode (LED) driver with a passive regenerative snubber is presented. In the proposed LED driver, the energy-transferring capacitor is not only used to step up the voltage gain but also to achieve the current balance among LED strings. Moreover, a passive regenerative snubber is added not only to recycle the leakage inductance energy but also to improve the voltage gain. As compared with the prior work, only one switch is required. Thus, the configuration of the proposed LED driver is simpler. Since the proposed LED driver has a higher voltage gain than the prior work, the turns ratio of the proposed LED driver can be lower. Thus, the magnetic core size can be reduced. In addition, both LED drivers have the same component count. Finally, the operating principle, analysis, and experimental results are provided to verify the effectiveness of the proposed LED driver. [ABSTRACT FROM AUTHOR]

Higher power applications require a multilevel converter to meet high power ratings. A multimodule current-source converter (CSC) can provide a multilevel current waveforms and at the same time eliminate the bulky transformer at the ac side. However, it is required for the multimodule CSC to use multiple dc-link inductors for the purpose of power balance among different modules. Thus, one key issue in the design of the multimodule CSC is to balance the current through different dc-link inductors. This paper focuses on studying the control strategy of the multimodule CSC and a generalized current balancing method is presented. As presented, zero vectors are distributed based on the deviation of the dc-link inductor currents and the comparison of the capacitor voltages. Therefore, the current imbalance problems, not only those among the upper inductors but also those among the lower inductors are solved. Moreover, since the current balancing algorithm is not dependent on module numbers, the presented control strategy is very suitable for modularization. Especially, with the feedback of the capacitor voltages, the resonance arising from the inductor-capacitor (LC) filter is damped. In addition, a design method of the dc-link inductors is also derived. Finally, simulation and experimental results show the validity of the propositions. [ABSTRACT FROM AUTHOR]

This paper presents a capacitor-isolated light-emitting diode (LED) driver with inherent current-balancing capability. Based on a series resonant converter, the resonant capacitor can be used both for safety isolation and the current balancing with the proposed two-output rectifier structure. Compared to the conventional current-sharing technique, the proposed LED driver circuit is simple and has low cost and high performance. Also, the capacitor-isolated structure is more efficient and compact compared to the conventional transformer isolation. The detailed theoretical analysis and design considerations of the proposed circuit are presented. The performance of the proposed circuit is validated by the experimental results from a 60-W prototype with two balanced outputs. [ABSTRACT FROM AUTHOR]