Search

Effect of Si addition on the high temperature tribological properties of TiZrV 0.5 Nb 0.5 refractory high entropy alloy was systematically studied. The results demonstrate that Si-microalloying affects the tribological properties by modulating the evolution of tribo-layer. Si-microalloying produces local tribo-layer with strong wear resistance by increasing the sintering rate of wear debris below 600 ℃, ultimately significantly reducing the coefficient of friction and wear rate. At 600 °C, Si-microalloying deteriorates the wear resistance due to the stress concentration at hard particles leading to accelerated fracture of the tribo-layer which hinders the formation of continuous protective tribo-layer. The enhanced tribological properties at 800 °C are attributed to the synergistic effect of suppressed oxide volatilization and rapid oxidation behavior ensuring continuous dense tribo-layer formation. • The high temperature tribological properties of TiZrV 0.5 Nb 0.5 Si x RHEA was studied. • The evolution of the tribo-layer plays a crucial role in the wear process. • The sintering rate of debris determines the formation of tribo-layer below 600 ℃. • A continuous and dense tribo-layer was formed for the Si0.3 alloy at 800 °C. [ABSTRACT FROM AUTHOR]

The tribological behaviors of the (W 0.67 Al 0.33 )C 0.67 –Co/fluoride (CaF 2 , BaF 2 , CaF 2 /BaF 2 ) composites against SiC ball from room temperature to 600 °C were investigated. A marked increase in the friction coefficient resulting from fluoride oxidation was observed as the temperature increased. The composites containing BaF 2 or (Ca, Ba)F 2 displayed better integrated wear resistance over a wide temperature range compared with (W 0.67 Al 0.33 )C 0.67 –Co/CaF 2 . The high temperature tribological characteristics of the three composites were distinct, which originated from the composition difference on the worn surfaces. First, the SiO 2 /SiC film formed on the worn surfaces of the composites with BaF 2 or (Ca, Ba)F 2 was favorable for their wear resistance. Second, the oxidation of WC matrix was an important factor influencing the wear resistance of the composites. When mixture oxides of WO 2 and WO 3 appeared on the surface, wear is severe. In addition, single WO 3 formed on the worn surfaces, appeared more adhesive to the underlying substrate and decreased the wear rate. [ABSTRACT FROM AUTHOR]

Abstract: In this paper, a series of ZrO2 matrix high-temperature self-lubricating composites were prepared by hot-press technique. The effect of Mo and Ag on the friction and wear behavior of the ZrO2(Y2O3)–Ag–CaF2–Mo composites in a wide temperature range was investigated. The XRD results showed that CaMoO4 formed on the worn surface above 400°C. The excellent lubrication performance of CaMoO4 endowed the low coefficient of friction of the ZrO2(Y2O3)–Ag–CaF2–Mo composites at high temperatures. The ZrO2(Y2O3)–10Ag–10CaF2–10Mo composites showed favorable wear resistance at all the tested temperatures which was attributed to the combined action of hardness and phase transformation. [Copyright &y& Elsevier]

Abstract: The high-temperature tribological behaviour of Fe–28Al–5Cr alloy and its composites containing TiC was investigated against a Si3N4 ceramic from 25 to 800°C. The high-temperature wear resistance of the materials was significantly improved by the addition of TiC, which was attributed to the high hardness of the composites, as well as the support role of hard TiC. The oxidation played an important role to friction and wear. [Copyright &y& Elsevier]

Abstract: A Ni3Si–Cr7C3 composite coating was fabricated on AISI 1020 steel substrate by self-propagating high-temperature synthesis (SHS) casting route. Phase composition, microhardness and dry sliding wear behavior of the coating were studied. The results indicated that the coating was mainly consisted of Ni3Si and Cr7C3. The microhardness of coating is about 900HV. The friction and wear tests showed that although the friction coefficient had no obvious change, the wear resistance of the AISI 1020 steel matrix was improved greatly. Also, the corrosion test result showed that the coating had an excellent corrosion resistance. [Copyright &y& Elsevier]

High entropy alloys (HEAs) are an important candidate for high temperature mechanical systems. Here, effects of atmosphere, temperature and counterparts on the vacuum tribological behaviors of CoCrFeNi HEA fabricated by spark plasma sintering were systematically studied. Comparison of tribological behaviors in vacuum and air indicated that tribo-oxidation is detrimental to the wear resistance of CoCrFeNi HEA within temperature range 25–400 °C, but positive at 600 and 800 °C. The CoCrFeNi HEA obtains relatively low wear in vacuum when low testing temperatures and heterogeneous counterface are selected. The wear resistance of CoCrFeNi HEA in vacuum is superior or comparable to the steel and intermetallics. • The high-temperature tribological behaviors of CoCrFeNi HEA were studied. • Tribological properties of HEA depend on atmosphere, temperature and counterparts. • Tribo-oxidation is negative for the wear resistance below 600 °C but positive above. • In vacuum, surface oxidation, adhesive and mechanical properties determine the wear. [ABSTRACT FROM AUTHOR]