Search

The variability and inhomogeneity of solar energy limits the development of solar heating systems (SHS) in many fields. In order to improve the utilization efficiency of SHS, this paper takes three typical cities (Xi'an, Dunhuang, Lhasa) as the research object, studies the operation state of SHS in student dormitory buildings, and puts forward a corresponding optimization strategy. The research shows that the reduction of water supply temperature will improve the operation efficiency and energy saving effect of a spontaneous combustion heat pump and that there is an optimal volume of heat storage water tank (HSWT), which can make the energy saving effect of SHS run better. The optimization of the SHS shows the water supply temperature is 35 °C, and the optimal volume of HSWT is 15 m3 in the "Resource-general area (Ⅲ)" represented by Xi'an, 25 m3 in the "Resource-rich area (Ⅱ)" represented by Dunhuang, and 40 m3 in the "Resource-richer area (Ⅰ)" represented by Lhasa. With the increase in the abundance of solar energy resources in the region, the optimal volume of HSWT also increases. Meanwhile, the solar energy contribution rate of the three regions in descending order is 61.3% (Lhasa), 32.8% (Dunhuang), and 25.9% (Xi'an). After optimization, the contribution of SHS increased by about 5%. The research results will help improve the efficiency of SHS in cold areas of China and make the system more efficient and energy efficient during operation. [ABSTRACT FROM AUTHOR]

Solar heating technology has the advantages of being high efficiency, energy-saving, and environment protecting; however, the instability of solar energy and its mismatch with the variation characteristics of building heat load have caused great difficulties in the design and the efficient operation strategy of a solar system. A heat storage tank is an important part of a solar hot water system. In order to improve system efficiency, this paper proposes a flat plate PCM storage tank, establishes a mathematical model, and conducts experimental verification under different working conditions. Experiments show that in the heat storage process, the phase change material (PCM) only accounts for less than 20% of the space of the PCM storage tank, and its heat storage can reach 50% of the total heat storage of the tank. In the discharge process, the water temperature of the ordinary tank decreases by 20 °C within 1.5 h, and the phase change process lasts approximately 3 h, with the water temperature remaining at 45~50 °C during this period. In the natural cooling process, the heat discharge of the two water tanks at night was similar, while the temperature of the ordinary water tank decreased by 12 °C and that of the phase change water tank decreased by 7 °C. By simulating the dynamic simulation model of the composite solar phase change thermal storage combined with an air-cooled heat pump system, the results show that the solar heating system with a PCM storage tank (SHS-PCM) saves 34% more energy than a solar heating system with a common tank (SHS-without PCM), and the volume of the PCM storage tank is reduced to 1/5 of the ordinary tank. The investment payback period method of energy saving reconstruction is used to analyze the economy of the SHS-PCM and the SHS-without PCM, the initial investment cost of the SHS-PCM is CNY 9858 higher than the SHS-without PCM, but the annual operation cost is saved by CNY 12,100, and the project investment payback period is 0.81 years, which has energy-saving potential and economic benefits. [ABSTRACT FROM AUTHOR]

Research activity in the field of combined cooling heating power (or trigeneration) systems with high renewable energy source (RES) contributions has increased rapidly over the last few years, in line with the European Union legislation about energy communities. However, technical challenges arise regarding the synergetic, sustainable and optimal integration of RES in local energy systems. In the present study, the operation of a trigeneration system located in the student residences of Democritus University of Thrace in Greece is examined. The system involves a combination of highly promising renewable and storage technologies, including solar thermal energy and biomass for heat generation, hot water tanks for thermal energy storage, absorption refrigeration for cooling, along with Organic Rankine Cycle and photovoltaic systems for electricity generation. System modeling and simulation have been implemented in Dymola environment with the use of Modelica equation-based modeling language. The accuracy of the model response has been validated against available measurements. Specific design and control measures have been proposed, simulated in a transient fashion and evaluated in terms of (i) RES generation, (ii) solar fraction and (iii) temporal flexibility. The measures examined, including the placement of a Li-ion battery, resulted in an increase of 24.6% in the heating demand solar contribution and of 7.9% in the renewable energy generated for the electricity demand, over the examined periods. [ABSTRACT FROM AUTHOR]

The harsh indoor environment in winter in the hot-summer and cold-winter zones of China and the increasing demand for winter heating from residential consumers have prompted more and more researchers to address the energy-efficient heating problem in non-centralized heating areas. A computational fluid dynamics model of a typical building was developed to analyze the dynamic heat transfer characteristics and energy consumption of interior partitions under decentralized heating in this region, of which the accuracy of the established model was proved by the relative error of less than 5% compared with the experimental measurement. Then seven typical kinds of interior partition configurations with different wall thickness, wall material, and insulation layer locations were developed and evaluated through simulation analysis. Transient heat storage ratio and cumulative heat storage ratio were proposed to demonstrate the dynamic heat transfer characteristics of interior partitions. The simulation results showed that 180 mm and 220 mm solid clay bricks can reduce energy consumption by 17.56% and 30.23%, respectively, compared with 120 mm solid clay bricks. The energy consumption of fly ash aerated concrete and solid clay brick partitions were reduced by 10.18% and 19.02%, respectively, compared with porous concrete partitions. The dynamic heat transfer characteristics of internal partitions with internal insulation were similar to those with external insulation due to the reduction in unnecessary energy consumption transferred to adjacent unheated rooms by about 20% compared to that without insulation. And the heat consumption of interior partitions under convective heating was 17.3% higher than under radiant heating. [ABSTRACT FROM AUTHOR]

Decarbonising the industrial sector is a key part of climate change mitigation targets, and Solar Heat for Industrial Process (SHIP) is a promising technology to achieve this. However, one of the drawbacks of SHIP systems is that they rely on an intermittent energy source. Therefore, sensible energy storage has emerged as a potential solution. In addition, solid byproducts have been proposed as a low-cost but effective material for thermal energy storage (TES). This work presents a SHIP system model coupled with a copper slag-packed-bed TES (PBTES) model using air as heat transfer fluid. The TES has been implemented to preheat the makeup water of the tank where steam is generated. A system design was carried out using a parametric analysis to find a solar field size and a corresponding TES volume. The resulting system was simulated, and the operating variables were analysed in detail. The results show that it is possible to generate 20% more energy due to the storage system. Additionally, a techno-economic analysis indicates that the SHIP with PBTES system results in a payback period of 14 years and a savings of C O 2 emissions of 30 t C O 2. • Integration of a SHIP system with copper slag packed-bed TES • Dynamic simulation and analysis of the system's main variables • System performance assessment and control improvement • Techno-economic analysis of the entire system and carbon savings • SHIP system with TES presents a payback of 14 years and annual savings of 30 tCO2 [ABSTRACT FROM AUTHOR]

Thermal energy storage is a key issue in efficient energy system applications, especially in renewable energies. In this respect, phase change materials (PCM) have attracted interest as an active solution for efficient energy management, particularly in the building sector. This paper presents a modelling of a PCM thermal battery in solar system assisted by heat pump. The storage stores the heat produced by unglazed solar panels (Batisol®) and releases it into a heat pump. Then this heat is sent to two other PCM storages. In this way, the low-temperature heating and domestic hot water needs of a commercial building in winter are met. The storage consists of a block of PCM contained between two plates of heat transfer fluid. It acts as a plate heat exchanger that can be charged and discharged simultaneously. The objective of the study is to dynamically simulate the thermal behaviour of this storage for different hot inlet temperature profiles. A rectangular profile is used to validate the model using experimental results. Then, a solar system assisted by heat pump and three PCM storages is dynamically simulated. This 2D model would be useful to validate a simpler model for optimising the operational parameters of the system. • PCM thermal battery acts as plate heat exchanger which can be charge and discharge simultaneously. • PCM storage model is validate using experimental results. • Three different PCM are chosen according to the temperature levels of each application. • A solar system assisted by heat pump has been dynamically simulated to supply DHW and low-temperature heating requirements. • No auxiliaries are required to meet the building's needs. [ABSTRACT FROM AUTHOR]

Sensible thermal energy storage is the most common solution for small-to-medium solar process heat systems. Hence, it is vital to enhance the thermal stratification and energy utilization of stratified tanks. In this study, four process heat systems are dynamically simulated: 1) S0 with a single outlet port to the load, 2) S1 with a single port and a thermostatic mixing valve, 3) M0 with multiple ports, and 4) M1 with multiple ports and a mixing valve. Two novel models are proposed for the compound parabolic collectors and the stratified tanks. System M1, with annual system efficiency of 47.3% and solar fraction of 0.57, was found to be the best-performing one, followed by S1, M0, and S0. System M1 also reduced the annual energy consumption of the backup heater in S0 by 16.45%. The thermostatic mixing valve reduced the thermocline thickness. The incorporation of both mixing valve and multiple ports delayed the startup of the heater, reduced the system's thermal losses, and slightly improved the collectors' efficiencies. The proposed tank model can be a viable tool for solar energy designers to optimize the number and relative positions of the inlet and outlet ports for maximized system efficiency and solar coverage. [Display omitted] [ABSTRACT FROM AUTHOR]

A centralized solar hybrid heating and cooling system satisfying the thermal, cooling and sanitary water demands of a typical Italian small district composed of six residential buildings situated in Naples (southern Italy) is modelled, simulated and analysed through the software TRNSYS over a period of 5 years. The plant is based on the operation of solar thermal collectors coupled with seasonal borehole storage; the solar field is also composed of photovoltaic solar panels connected with electric energy storage. An adsorption chiller powered by solar energy is adopted for cooling purposes, while a condensing boiler is used as an auxiliary unit. The performance of the proposed system has been assessed from energy, environmental and economic points of view and contrasted with the operation of a typical Italian heating and cooling plant, highlighting the following main results: saving of primary energy consumption up to 40.2%; (decrease of equivalent CO2 emissions up to 38.4%; reduction of operating costs up to 40.1%; and simple pay-back period of about 20 years. [ABSTRACT FROM AUTHOR]

• Annual dynamic simulations of solar water heating system with and without phase change materials were conducted. • A thorough parametric study was carried out in different climate zones. • Optimization of phase change temperature and design parameters usage amount was performed. • The highest power saving rate using phase change material is 31% in Lhasa. • The highest heat loss saving rate using phase change material is 9.9% in Guangzhou. Recently there have been many reports on the application of phase change materials (PCM) in solar water heating system (SWHS). However, there are some doubts and different views in this field, since the sensitivity of the system to the PCM design parameters and external conditions. In this study, a typical SWHS with a PCM storage tank is proposed to overcome the existing problems. The mathematical model is established and validated against experimental data. Annual simulations have been done under a typical user load and different PCM design parameters (phase change temperature, PCM usage amount) among six cities which have different meteorological conditions. The results indicate that the application of PCM in SWHS can reduce the power consumption of electric auxiliary heater (EAH) and the heat loss, but the benefits vary widely by regions and PCM design parameters. The highest power saving rate is up to 31% in Lhasa which has extremely abundant solar energy, while for the heat loss saving rate the highest value is 9.9% in Guangzhou which is located in the hot summer and warm winter zone. Besides, a parametric study has been conducted to explore the power saving potentials with different PCM design parameters in different regions, as well as to discuss the optimal phase change temperature and the PCM usage amount. This study aims to provide theoretical references and suggestions for the design of the PCM storage tank in SWHS. [ABSTRACT FROM AUTHOR]

A hybrid ground-coupled heat pump (GCHP) is an efficient and sustainable technology for space heating and cooling. A demonstration house equipped with GCHP with a solar seasonal heat storage (SSHS) system had been built in Harbin, a severe cold zone of China. A dynamic simulation model was built for the house and GCHP with the SSHS system using TRNSYS. The model used a newly developed vertical ground heat exchanger (VGHE) module which considered coupled heat and moisture transfer (CHMT) in ground with variable soil properties (VSPs) and phase change of soil moisture (PCSM). In the simulation, a large amount of computing is consumed for VSP and PCSM, while the computing amount for moisture transfer is small. The model with the new VGHE module produced better simulated results, compared with the field data. So, CHMT-VSP-PCSM affects the performance of VGHE and system to some extent, especially CHMT. Hourly variation laws of temperatures and energy parameters were analyzed, and different characteristics were showed up at different operating stages in heating and cooling seasons for both long and short terms. The GCHP with the SSHS system can meet the heating and cooling demands of the house in general. In cooling season, adjusting the ratio of the two groups of VGHE for heat storage and cooling will increase the utilization efficiency of VGHE and make the soil temperature more balanced. [ABSTRACT FROM AUTHOR]

Abstract Integration of a latent heat energy storage into a solar heating system has become a well-known engineering practice that can bridge the mismatch between the heat demand of the served building and heat supply from the solar heating system. However, control schemes, energy performance analysis, characterization and optimization of such a system under the Tibet climatic/altitude conditions still remain a challenge. This research aims to investigate a PCM-integrated solar heating system applicable to Tibet which is unique in terms of the altitude, solar radiation, atmospheric pressure and water boiling temperature etc. The whole process involves (1) identification of the unique features of Tibet climate and altitude and relevant requirements to the solar system; (2) design of a PCM-integrated solar heating system based on a selected building in Lhasa and planning the potential control strategies appropriate to such a system; (3) analysis of the system's energy performance under different operational schemes; and (4) recommendation of the most appropriate system operational scheme and design strategy. A dynamic simulation model was established and applied to study the energy performance of such a system, in which the solar energy usage rate is defined as the performance evaluation index. It is found that the operational scheme 'A' has the best energy saving effect, followed by operational schemes B and C. The system presents a more favorite energy performance between 9:00 h–18:00 h, compared to other time slots in a typical winter day. Change in operational schemes creates a significant impact on the energy saving effect of the system. The results help wide and fast deployment of the PCM-integrated solar heating system and enable the determination of the best performing operational scheme and associated performance data appropriate to Tibet or similar regions in the world, thus making a significant contribution to the saving of fossil fuel energy consumption and reduction of the carbon emission on the regional and global scales. Highlights • Energy performance and operational schemes of a Tibet-focus SHS-PCM was investigated. • Operational scheme A is the best and C is the worst in terms of energy saving rate. • Daytime heating achieved a higher energy efficiency compared to the full day heating. • Energy saving rates for three schemes are 64%, 50% and 46% for the full day heating. • Energy saving rates for three schemes are 92%, 79% and 24% for daytime heating. [ABSTRACT FROM AUTHOR]

As a result of the increased penetration of intermittent renewable energy sources, Combined Heat and Power (CHP) units are being looked upon as one of the sources that might provide for the ever growing need for electrical flexibility. However, CHP units are often considered as must-run units on the grid for their main purpose is generally to cover the heat demand of an adjoining District Heating Network (DHN). This paper demonstrates how a CHP–DHN system may be used as a frequency reserve without excessively compromising the lifetime of the CHP, using either a specific storage tank or the DHN's thermal inertia in order to compensate for the resulting heat imbalance. In the latter case, it is shown that a buffer tank, although smaller than a specific Thermal Energy Storage (TES), is required due to restrictions for acceptable DHN temperature gradients. In both approaches, the size of the tank has been mapped out considering frequency reserve's duration and capacity. The results show that a simplistic static model of the DHN is sufficient for the design of a specific TES, while a detailed dynamic simulation is required when the DHN is used as storage, to prevent overestimating the flexibility of the CHP–DHN system. This research could be used to assess the potential for improving CHP–DHN systems flexibility, using them as frequency reserves, and to design the required storage or buffer tanks. • A control strategy to use a CHP-DHN system as a frequency reserve is proposed. • Dedicated storage tanks and/or DHN thermal inertia are used. • The DHN can be used as heat storage, but a buffer tank is required. • A detailed dynamic DHN model is needed to determine the DHN flexibility. • The flexibility of the CHP–DHN system was determined for 370 MW CHP. [ABSTRACT FROM AUTHOR]

Abstract: With a view towards better efficiency in renewable energy utilisation, particularly solar energy, the authors study a long-term solar thermal energy storage based on water absorption by a lithium bromide aqueous solution. After a description of the process, the system dynamic simulation model is detailed and used to investigate the influence of certain parameters (heat exchanger size, solution flow rate, absorption percentage) and operating conditions (heat supply temperature to the building, crystallisation ratio, heat need) on the system performance (storage density, thermal efficiency, etc.). The analysis of simulations made for a low-consumption building in Chambéry shows that the solution flow rate is a critical parameter in the process performance. It also appears that crystallisation in the solution storage tank increases the storage density more than three times. The simulation results are used in the design of a prototype that is under experimentation for validation of the model. [Copyright &y& Elsevier]

Ulaanbaatar (Mongolia) is the coldest capital city in the world with approximately 98% of its heating demand satisfied by means of coal-burning stoves. This leads to enormous air pollutant emissions, with Ulaanbaatar being one of the top five most polluted cities in the world. In this study, an innovative solar hybrid heating system for the Mongolian scenario was used, which was based on the operation of a solar field composed of four series-connected evacuated tube heat pipe collectors, coupled with a thermal energy storage. The solar hybrid heating system was simulated and analyzed using the software TRNSYS. The simulations were designed to satisfy the heating demand of a typical single-family detached house located in Ulaanbaatar and were carried out with and without considering the soiling effects on the solar system operation. The overall performance of the proposed plant was compared with those associated with different fossil fuel-based Mongolian conventional heating systems, in order to assess the potential energy, environmental and economic benefits. The results highlighted that the proposed plant allowed for the obtainment of significant reductions in terms of primary energy consumption (up to 34.6%), global CO2 equivalent emissions (up to 52.3%), and operating costs (up to 49.6%), even if the expected return on the investment could be unacceptable. [ABSTRACT FROM AUTHOR]