Search

Boost power factor corrections tend to be considerable sources of electromagnetic disturbances. To ensure the proper functionality of susceptible systems in the vicinity, the emissions must be reduced. Passive filters, as a conventional solution to reduce conducted emissions, usually suffer from their high volume, weight and costs. Active filters can help to mitigate this problem, but the known solutions are systematically limited by inherent time constants and signal propagation delays since they derive the cancellation signal directly from a measured quantity by a feedforward and/or feedback approach. To resolve this issue, each harmonic can be individually suppressed by an artificially synthesized sine wave that is synchronized to the disturbances. By adjusting the amplitudes and phases of the suppressing sine waves, bothersome time constants and delay times can be compensated. In this work, it is shown that the switching harmonics of a power factor correction can be interpreted as modulated sine waves. By modulating the suppressing sine waves simultaneously, a very high performance can be achieved for the active cancellation system. The hardware and the algorithm are described, optimum parameters for the algorithm are identified and an FPGA implementation is applied to a real PFC.

The high-frequency switching of power transistors in electronic systems can be a significant source of electromagnetic emissions (EMI). Simple measures like reducing the high-frequency disturbances by introducing an additional gate resistor lead to an increase of the switching losses. This creates a conflict of interests between the reduction of disturbances and high system efficiency. More complex active gate drivers offers improved compromises between EMI and efficiency. Avoiding steep switching slopes, overshoots or sharp edges are typical measures. The whole spectrum is modified this way and efficiency is still affected. In many cases, only a narrow banded modification of the spectrum might be needed to avoid the excitation of critical system resonances. This can be reached by a target signal-oriented control of the gate of the transistors. In the target signal the critical RF components should be reduced. Maximum control of the target signal is possible with fully synthesized gate signals. The reduction of some harmonics in the switching spectrum may lead to overshoots in time domain due to the Gibbs phenomenon. These overshoots may violate the physical limits of a transistor and cannot be realized. In this work, a method is presented to determine the target signal considering all physical limits. The found approach is applied in simulation to the signal of the drain-source voltage of a boost converter to reduce the harmonics in the FM broadcasting range. The gate control signal is determined for this application.

In many modern power electronic systems, fast-switching semiconductor devices are used to reduce switching losses. Due to steep switching waveforms and high switching frequencies, significant electromagnetic disturbances can be emitted. In contrast to conventional passive filter components, active cancellation methods are based on the controlled destructive interference between a noise signal and a corresponding anti-noise signal. Adaptive notch filters revealed themselves as a promising active EMI cancellation concept for periodic noise signals. In this work, adaptive notch filters are regarded in context of slowly time-varying periodic noise signals, e.g. pulse-width modulated signals as common in inverters. The corresponding noise signals consist of switching harmonics and adjacent sideband harmonics. Therefore, the notch filter’s bandwidth comes into focus and an analytical approximation for the ideal adaptive notch filter’s bandwidth is discussed. With help of this approximation, the adaptive notch filter can be parametrized specifically to a given noise spectrum and other requirements. The capability of the parametrization strategy and the adaptive notch filter itself are shown by simulation and measurement.

Active cancellation of disturbing signals is a common method in electromagnetic compatibility (EMC) of power electronic systems. In this paper, a new method of suppressing periodic disturbances is extended and applied. In this method, the disturbing harmonics are suppressed by a synthesized cancellation signal that is synchronized with the converter's operation. Here, the cancellation signal is synthesized from a number of destructive sine waves. The appropriate amplitudes and phases are found via a convenient and robust adaptive approach. As a special feature of this method, many troublesome effects, like delays or complex frequency characteristics, can be compensated easily. Therefore, this method does not suffer from the same limitations as previous active techniques. Until now, the method has only been proven for a small number of harmonics. In this study, it is applied to a wide frequency range of 150 kHz to 30 MHz of a 48-/12-V dc/dc converter, e.g., for automotive applications. An optimization strategy is developed from a causal model of the system. A test setup is realized, and the sensor's and injector's performances are discussed regarding the automotive EMC standard CISPR 25. Measurement results for the artificial network and the antenna are presented. The additional power losses are estimated.

Active cancellation of disturbing signals is a common method in EMC. In this paper, a specialized strategy is presented to minimize the disturbing harmonics of stationary clocked systems by injecting an appropriate harmonic cancellation signal with an adjustable signal synthesizer. The optimum cancellation signal is found via a convenient and robust adaptive approach. Each destructive harmonic is generated individually, and the cancelation signal is the superposition of a set of sinusoidal signals. As a special feature of this method, many troublesome effects, like delays or complex frequency characteristics, can be compensated easily. Several implementation variants can be derived from this general approach. Here, the variant, continuously adapted harmonics cancellation (CAHC), is considered. The system's limitations due to the ADC, the DAC, and the synchronization are described. An FPGA-implementation of CAHC is presented and applied to a dc/dc converter in an automotive component measurement setup to demonstrate the effectivity of the method.

Active cancellation is a promising solution to reduce the size of passive filter components. Considering power electronic systems in stationary operation and with periodic control signals, the disturbances consist of stable harmonics that can be individually suppressed by destructive sine waves. These sine waves can be superposed to create a synthesized broadband cancellation signal that must be injected in synchronicity with the operation of the power electronic system. Since bothersome effects (like time constants or delay times) can be compensated by appropriate amplitudes and phases of the cancelling sine waves, the active cancellation system can achieve high EMI reductions in a wide frequency range. In this work, the method is applied to a motor inverter with a very large number of differential mode (DM) harmonics. The characteristics of the disturbances are discussed and the challenges for the active EMI cancellation system are elaborated. A suitable method for the determination and generation of the cancellation signal is introduced. This method is applied to a GaN inverter with a synchronous machine in the frequency range from 50 kHz to 30 MHz. The EMI suppression is evaluated by average and peak measurements with an EMI test receiver. The power of the generated cancellation signal is estimated.

This paper deals with the application of spread spectrum techniques on power electronic converters to reduce electromagnetic disturbances. These techniques aim for a spreading of the harmonics in a frequency domain in order to distribute the power over a wider frequency range. By doing so, the levels of the harmonics drop. In this paper, both peak and average detector measurements are considered. It is shown that different parameters are required to minimize either peak or average emissions. The reduction of peak and/or average emissions is mathematically described for a sine wave as a harmonic of pulse width modulation signals. These spread harmonics overlap for high orders and/or high-frequency variations. It is shown that this effect is a limiting factor for spread spectrum in practical applications. The resulting maximum achievable reduction is analyzed. From these results, parametrization strategies are derived to fulfill specific requirements. In test setups, the precision of the proposed parametrization strategies is demonstrated. Additionally, it is shown that the results for peak measurements can also be applied to quasi-peak measurements.

Active cancellation can suppress electromagnetic interference (EMI) of clocked systems like power electronic converters. Considering clocked systems that operate stationary over a sufficient time, there are stable harmonics that can be individually suppressed by destructive sine waves. These sine waves can be superposed to create a synthesized wide bandwidth cancellation signal. Adaptive approaches have proven to be very effective to find the right parameters for each sine wave. Bothersome effects, like complex frequency characteristics or delays, can be compensated by appropriate amplitudes and phases. Therefore, this method does not suffer from the same limitations as active techniques with feedback- or feedforward-topologies. If the disturbances are constant over a sufficient time, the parameters for the cancelling sine waves can be found simultaneously or successively. Until now, only the first option has been shown with an adaptive cancelling FPGA system. Since the cancelling logic needed to be implemented for each cancelling sine wave and the resources of any FPGA are limited, the number of suppressible harmonics was limited as well. In this work, this limitation is resolved by a successive approach that enables the application of the method to a very large number of harmonics. The fundamental theory is discussed, and a robust algorithm is presented. A cancellation system is realized and applied to a 48V/12V DC/DC converter (e.g. for automotive applications) to suppress the frequency range of 150 kHz to 30 MHz in regard to the automotive EMC standard CISPR 25.

Cancellation of disturbing signals is a common strategy in EMC. In this work, a specialized strategy is developed to cancel the disturbing harmonics of stationary clocked systems. This strategy is refined by an adaptive approach to conveniently find the optimum signals for cancellation. As a special feature of this method, all troublesome effects, like delays or attenuations, can easily be compensated. From a basic theory, two implementation variants are derived: 1) Continuously Adapted Harmonics Cancellation (CAHC) and 2) Previously Adapted Harmonics Cancellation (PAHC). CAHC is implemented on an FPGA-system. The hardware, programming and performance of the utilized FPGA and its peripherals are transparently discussed. The effectivity of the method is demonstrated for a power electronic dc-to-dc converter.

This work deals with the adaption of PWM frequencies to a chosen AM or FM broadcast channel in a vehicular application. To do so, the radio passes the information of the current receive channel to EMI sources that utilize PWM signals. By this feedback loop, the switching harmonics can be shifted in such way, that the respective receive channel is free of disturbances. For the adaption, two different strategies are derived, analyzed and applied: Harmonics shifting and zero harmonics shifting. These strategies prove to be viable options that help to fulfill vehicle-internal EMC demands that mostly are much stricter than legal regulations and international standards.