Search

In this article, a new dual-permanent magnet spoke-type flux-reversal machine (dual-PM SFRM) for direct-drive applications is proposed. Tangentially magnetized permanent magnets (PMs) sandwiched with iron poles are set in stator slots. To increase the torque density within the geometric restrictions, PMs are introduced in the rotor as well and magnetized radially to form a consequent-pole rotor. Global optimizations are conducted and comparisons are made on torque, torque ripple, and torque/PM volume with the existing single-PM SFRM. It is found that the proposed dual-PM SFRM can produce 22.6% larger torque with an optimal PM volume and a 17.5% larger torque with the same PM volume compared with the single-PM counterpart. Moreover, major magnetic field space harmonics are derived analytically and verified by finite-element analysis (FEA) and the torque components produced by the working harmonics are calculated and compared in terms of different stator/rotor pole number combinations. Comparisons are made on back electromotive force, cogging torque, torque performance, and efficiency between dual-PM SFRM and conventional flux-reversal machine. The influence of different stator configurations, i.e., the slot opening, the iron bridge, and the unequal tooth, on torque performance in the proposed dual-PM SFRM has been studied and highlighted. A prototype has been built and tested to validate the FEA calculations. [ABSTRACT FROM AUTHOR]

Consequent-pole (CP) permanent magnet (PM) configuration suffers asymmetric electromagnetic characteristics although it saves PM usage. The CP-based stator-PM synchronous machines are investigated in this paper, with particular reference to symmetrical issues. The electromagnetic performances of the CP-based stator-PM synchronous machines are firstly evaluated. Afterwards, the rule of even order harmonics cancellation is presented for different slot/pole number combinations and winding layouts, based on which symmetrical phase flux-linkages can be obtained although the unbalanced magnetic flux naturally occurs. Moreover, based on the three-dimensional finite element analysis, the unipolar end leakage-flux caused by the asymmetric magnetic field is identified, and the risk of the shaft magnetization is revealed. Finally, a pair of prototype machines are fabricated and measured to validate the analyses. [ABSTRACT FROM AUTHOR]

Consequent-pole (CP) permanent magnet (PM) machines have attracted considerable interest as a means of reducing machine cost through a marked reduction in the volume of PM required to meet a particular torque specification. However, the presence of a large torque ripple that can result from the CPPM structure can hinder their adoption in some applications, especially for the dominant third-order torque ripple. Although several design-specific modifications have been proposed to ameliorate torque ripple, the generalized principles underpinning this behavior have not been fully established. In this article, it will be illustrated that an aggregation of the fluctuations in inductance, back electromotive force, and cogging torque contributes to increased torque ripple. Meanwhile, an asymmetric pole shaping method is proposed to reduce the torque ripple, taking the dominant third-order torque ripple as an example. Both simulated and experimental results of the 12-slot/8-pole prototypes show that compared to the symmetrical pole shaping model and the plain pole model, the proposed asymmetric shaping method is effective in reducing torque ripple. [ABSTRACT FROM AUTHOR]

Consequent pole (CP) permanent magnet (PM) machines offer scope for reducing the quantity of PM material and hence cost compared to more conventional PM machine topologies of the same rating. In this type of machine, the rotor pole arc is usually optimized to realize the largest output torque with pole shaping methods used to reduce torque ripple. However, such approaches tend to be limited by constraints imposed on the pole shapes. It is a common practice to adopt similar PM and iron pole shapes, an approach that does not fully account for the different characteristics of PM and iron poles in CPPM machines, often leading to large even order harmonics in the airgap flux density. This article proposes a shaping method with a variable rotor profile and pole arc span being established by means of optimization by Genetic Algorithm. It is demonstrated that for a fixed quantity of PM material, different PM and iron pole shapes in combination with optimal PM and iron pole arc spans are essential for ensuring both maximum output torque and lower torque ripple when the due account is taken of flux leakage. It also demonstrates that since the flux density in the region under a PM pole is governed by the magnetic potential produced by magnets while it is governed by magnetic reluctance under iron pole, different PM pole and iron pole shapes are necessary to reduce the even-order harmonics in a CPPM machine and consequently to reduce torque ripple. The performances of optimized and more conventional CP machines are compared by finite-element method on 12-slot/8-pole prototype motors. [ABSTRACT FROM AUTHOR]

Current harmonics are ubiquitous in dual three phase (DTP) permanent magnet synchronous machine (PMSM) drives. Due to back electromotive force (EMF) distortion, significant current harmonics are generated in the DTP-PMSM system. The influence of back EMF harmonics is investigated in this paper and a novel switching-table-based direct torque control method to compensate the selected current harmonics caused by the back EMF harmonics is proposed. It shows that by employing different optimal action time durations for voltage vectors in the z1z2 subspace and setting the synthetic voltage vectors to non-zero, the stator flux harmonics caused by the back EMF harmonics can be selectively compensated, as verified by experiments. [ABSTRACT FROM AUTHOR]

In this article, a new type of consequent pole flux reversal permanent magnet (CFRPM) machine, which features more iron poles than PM poles under one stator tooth, is proposed to improve the torque density. The proposed CFRPM machine with 6 slots and 16 poles (6S16P) is compared with a 12S16P FRPM machine and its consequent pole type, as well as a conventional 6S4P surface-mounted PM (SPM) machine. The proposed 6S16P CFRPM shows the highest torque among the four machines, together with the highest torque per PM volume. For a fair comparison with the 12S16P FRPM machine and its consequent pole type, the torque ripple of the proposed 6S16P CFRPM is suppressed by using two-step skewed rotor. After employing 4° two-step skewed rotor, while exhibits comparable torque ripple, the proposed 6S16P CFRPM still has 43% and 22% higher torque compared with the 12S16P FRPM machine and its consequent pole type. [ABSTRACT FROM AUTHOR]

In the past, various fundamental model based sensorless control methods have been proposed. However, most of them are developed under a healthy condition. Hence, in this article, fundamental model based sensorless control of permanent magnet synchronous machines (PMSM) under rotor eccentricity (RE) is investigated which is a common issue in many drive systems. It is known that under RE, three-phase back-EMFs, flux-linkages, inductances, and torque will be influenced. Mathematical derivation reveals that these effects will cause undesired harmonics in the position estimation. Since the frequencies of these low-order harmonics are much smaller than the bandwidth of position observer such as phase-locked loop, it is difficult to effectively eliminate them. Hence, the conventional back-EMF method is modified by adding an adaptive notch filter to suppress these undesired harmonics. Furthermore, the RE effects on PMSM characteristics are examined by measurements. The modified position estimator is implemented on a dSPACE platform and is verified by experiment results. [ABSTRACT FROM AUTHOR]

In this article, spoke array permanent magnet (PM) flux reversal machines (SAPM FRM), which feature spoke array PMs distributed along the stator inner surface, are proposed to improve the torque density. Compared with the conventional surface mounted PM flux reversal machine (SPM FRM), the proposed SAPM FRM can produce about 100% larger torque with negligible torque ripple, as well as higher efficiency and higher power factor. Two prototypes have been built and tested to validate the theoretical analyses. [ABSTRACT FROM AUTHOR]

This article investigates the duty-ratio-based direct torque control strategies for dual three-phase permanent magnet synchronous machine (PMSM) drives. The classical switching-table-based direct torque control (ST-DTC) for the dual three-phase drives usually suffers from significant harmonic currents and a large torque ripple. To reduce the harmonic currents, 12 combined voltage vectors are generated and employed as active vectors. Then, the duty-ratio-based ST-DTC is introduced to reduce the torque ripple. Considering that the typical duty-ratio-based ST-DTC exhibits the drawbacks of machine parameter dependent and a certain degree of failure rate in the duty ratio regulation, a simple and effective method taking into account the effect of the machine speed is employed to obtain the duty ratio. Afterward, to prevent the issue of the inverter thermal imbalance caused by using only one type of zero vectors, two types of zero vectors are employed in the switching sequences. With the proposed method, not only the harmonic currents have been suppressed, but also the torque ripple can be considerably reduced, while the merits of the classical ST-DTC such as simple structure and excellent dynamic performance are preserved. The experimental results validate the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

This paper aims to identify the optimal number of flux modulation pole (FMP) in Vernier permanent magnet synchronous machines (VPMSMs) with concentrated tooth-coil windings. First, the influence of number of FMP on machine performance is revealed based on the unified permanent magnet magnetomotive force permeance analytical model. It is found that for a fixed stator slot number, there always exists an optimal number of FMP to maximize the torque, thanks to the enhanced contribution by the fundamental permeance harmonic. Then, the influence of critical dimensional parameters, including the machine diameter, the permanent magnet thickness, and the width of FMP, on the electromagnetic performance of VPMSMs with different numbers of FMP are parametrically analyzed by both analytical and finite element analyses. Results show that the VPMSMs with the optimal number of FMP always have advantages of a higher torque density together with a reduced PM volume, particularly for those with a relatively large diameter. Finally, two VPMSM prototypes with different numbers of FMP are manufactured and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

Fractional slot concentrated winding (FSCW) permanent magnet synchronous machines (PMSMs) have been a research hotspot over the past few decades. Recently, the magnetic gearing effect in FSCW PMSMs is revealed along with its gear ratio, which is a function of slot/pole number combination. At the design stage of FSCW PMSMs, one of the key issues is the selection of the slot/pole number combination. This paper shows that the gear ratio can contribute to a proper slot/pole number selection in any multiphase FSCW PMSMs by acting as a unified index for a quick overall performance comparison. In this paper, first, the magnetic gearing effect in FSCW PMSMs is explained and the gear ratio is further discussed. The advantages of adopting gear ratio as the overall performance index over other indices are revealed. The influence of the gear ratio on the winding factor, torque output, cogging torque, inductance, and rotor losses of three- and six-phase FSCW PMSMs is analyzed and validated by experiments, thus proving the analyses. [ABSTRACT FROM AUTHOR]

This paper aims to comprehensively analyze the influence of number of permanent magnet (PM) pieces on electromagnetic performance of flux reversal permanent magnet (FRPM) machines. First, the unified analytical model of FRPM machines having different numbers of PM pieces is established, from which the optimal number of PM pieces and the corresponding rotor pole number can be identified. It shows that by employing the optimal number of PM pieces instead of the conventional two on each stator tooth, additional back-EMF component can be generated which is beneficial to boost the machine performance. Then, the influence of critical design parameters including stator slot opening ratio, split ratio, and stator slot number is investigated, providing a guidance to the design of FRPM machines aiming at maximum output torque. In addition, both finite element analyses and experimental tests are conducted to verify the analytical analyses. For 6-slot-stator FRPM machines, experimental results show that more than 40% higher output torque can be achieved in the machine with optimal number of PM pieces when compared to the conventional one. [ABSTRACT FROM AUTHOR]

This paper provides a comprehensive analysis of performance difference among various kinds of flux reversal permanent magnet (FRPM) machines having different permanent magnet (PM) arrangements. Four PM arrangement types are, first, identified by the number and relative polarities of PMs on the stator teeth, and their influence on the equivalent pole-pair number of the armature winding and working harmonics of the air-gap field is revealed. Then, the torque variation against the rotor pole number of each PM arrangement is analyzed. The electromagnetic performance of four PM arrangements with a 14-pole rotor is compared in detail. It shows that the FRPM machine, in which four PM pieces are mounted on each stator tooth and two adjacent magnets on different stator teeth are of opposite polarities, offers the highest torque density and the highest efficiency, which make it promising in low-speed high-torque applications. In addition, four prototype machines are manufactured and tested to validate the findings. [ABSTRACT FROM AUTHOR]

A method for enhancing torque capability of a dual three-phase permanent magnet synchronous machine (PMSM) based on conventional dual three-phase drive system by injecting the fifth and seventh current harmonics without any hardware re-configuration is proposed in this paper. Compared with the third current harmonic injection, which is commonly used to enhance the torque capability of dual three-phase machine, the two isolated neutral points of each set of single three-phase windings do not need to be reconnected to the middle point of dc-link capacitors or an additional power switching bridge to provide flowing path for zero-sequence current. Further, no additional current sensors are required to obtain the feedback of zero-sequence current to regulate it effectively. For a prototype dual three-phase PMSM, the average torque increases approximately by 9% at the cost of 0.56% increase in the 12th harmonic torque ripple. The effectiveness of the torque capability enhancement is confirmed by experiments. [ABSTRACT FROM AUTHOR]

The relationship between the two-individual current control and the vector space decomposition (VSD) control for a dual three-phase permanent magnet synchronous machine (PMSM) is investigated in this paper. It is found that the VSD control is more flexible in controlling the fundamental current in \alpha \beta subplane and the fifth, seventh current harmonics in z_{1}z_{2} subplane with different proportional and integral (PI) gains, while the two-individual current control is comparable with the VSD control in having the same PI gains in the \alpha \beta $ and z_{1}z_{2} subplanes. It is also found that the two-individual current control may have potential instability issues due to the mutual coupling between the two sets of three-phase windings. If the mutual coupling between the two sets is weak to some extent, then the two-individual current control could have the same dynamic performance as the VSD control without the stability issues. Experiments are conducted on a prototype dual three-phase PMSM to validate the theoretical analysis. [ABSTRACT FROM AUTHOR]

The sensorless control performance of pulsating carrier signal injection employing zero-sequence voltage for dual three-phase (DTP) permanent magnet synchronous machine (PMSM) drives is investigated in this paper. This method has the synergy of high bandwidth of zero-sequence voltage method and high position estimation accuracy of pulsating injection strategy. However, such a method for single three-phase PMSM exhibits large oscillation in position estimation error due to undesirable harmonic components in the zero-sequence carrier voltage, and the existing compensation methods usually require complex structures or intensive offline measurements. As for DTP-PMSM, the undesirable harmonic components for the pulsating injection can be suppressed with an optimum phase shift between the two injected high-frequency signals. Besides, a new simple measurement method of zero-sequence carrier voltage is proposed with only one voltage sensor placed between the two isolated neutral points. As a result, the rotor position estimation accuracy can be significantly improved. The experimental results verify the effectiveness of the proposed method for DTP-PMSM. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel sensorless method for open-winding (OW)-permanent magnet synchronous machine (PMSM) (OW-PMSM) with circulating current suppression. First, a zero-sequence steerable space vector pulse width modulation together with zero-sequence controller (ZSC) is implemented to suppress the circulating current existing in the OW-PMSM drive system with common dc bus. Afterward, the zero-sequence back EMF reconstructed from the output signal of the ZSC is utilized to extract the position information via synchronous phase-locked loop-based position observer. Hence, the voltage transducer and resistance network used in the conventional zero-sequence back-electromotive force-based sensorless methods can be consequently eliminated. Moreover, the proposed method requires no machine parameters, such as winding resistance, d- and q-axis inductances which are indispensable for the conventional fundamental back-EMF-based methods. The voltage disturbance components due to the resistance, inductance, and rotating cross coupling voltage drops can be avoid. Therefore, stronger robustness against the variation of machine parameters due to load or temperature variation can also be obtained. Finally, the proposed method is validated via experiments on a 3-kW OW-PMSM drive system. [ABSTRACT FROM AUTHOR]

Due to asymmetric three-phase system and influence of inverter nonlinearity, large torque, and stator flux harmonics would exist in the space vector modulation-based direct torque controlled (DTC-SVM) three-phase permanent magnet synchronous machines (PMSMs). A general expression for electromagnetic torque is derived for DTC of asymmetric three-phase PMSMs considering the influence of inverter nonlinearity. To mitigate the influence of the undesired harmonics, a compensation method is developed by enhancing the standard proportional-integral (PI)-regulator in the torque and flux loops with appropriate resonant controllers. Since the 2nd- and 6th-order harmonics are the most dominant components, two resonant controllers tuning at the 2nd and 6th of stator angular frequency, respectively, are utilized. The proposed method can achieve good steady-state performance in terms of low torque and flux ripples, while keeping the merits of the conventional DTC-SVM strategy such as good dynamic torque response and machine parameter independence. The experimental results validate the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

A partitioned stator hybrid excited machine is proposed, in which the permanent magnets and field windings are alternately placed on an inner stator separated from the outer stator having armature windings. This machine inherits the features of brushless machines and benefits from better space utilization. The operating principle and the effects of slot/pole combinations are investigated in detail. Further, based on 2-D finite-element analysis, the electromagnetic performances of the proposed machines, including back-electromotive force, cogging torque, flux regulation range, torque capability, power factor and torque–speed curve, are evaluated. The results reveal that the proposed machines can exhibit wide flux regulation range as well as good torque density. The prototype is manufactured and tested to validate the predictions. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel rotor contour design for variable reluctance (VR) resolvers by injecting auxiliary air-gap permeance harmonics. Based on the resolver model with nonoverlapping tooth-coil windings, the influence of air-gap length function is first investigated by finite element (FE) method, and the detection accuracy of designs with higher values of fundamental wave factor may deteriorate due to the increasing third order of output voltage harmonics. Further, the origins of the third harmonics are investigated by analytical derivation and FE analyses of output voltages. Furthermore, it is proved that the voltage harmonics and the detection accuracy are significantly improved by injecting auxiliary air-gap permeance harmonics in the design of rotor contour. In addition, the proposed design can also be employed to eliminate voltage tooth harmonics in a conventional VR resolver topology. Finally, VR resolver prototypes with the conventional and the proposed rotors are fabricated and tested respectively to verify the analyses. [ABSTRACT FROM PUBLISHER]

The hybrid-excited stator slot permanent magnet (HSSPM) machines have good flux regulation capability due to the dc excitation. This makes them attractive candidates for variable speed applications. In this paper, the choices of stator/rotor pole combinations for an arbitrary number of armature phases are discussed. The three-phase 12-10/11/13/14 stator/rotor poles HSSPM machines with single- and double-layer windings are further investigated. Their open-circuit characteristics, torque, inductances, and unbalanced magnetic forces are comparatively studied using 2-D finite-element analysis (FEA). Finally, the 2-D FEA is experimentally validated. [ABSTRACT FROM AUTHOR]

In this paper, partitioned stator flux reversal permanent magnet (PS-FRPM) machines having different stator/rotor pole combinations with consequent-pole PM (CPM) stator are proposed and analyzed. Compared with the conventional 12-stator-pole PS-FRPM machines having 10-, 11-, 13-, and 14-rotor-pole rotors and surface-mounted PM (SPM) stator, the PM volume in the proposed PS-FRPM machines with CPM stator can be saved by 28.33%, 30%, 30%, and 33.33%, respectively, while the torque density are similar, i.e., 98.59%, 96.69%, 95.50%, and 97.15%, respectively. Besides, the proposed PS-FRPM machines with CPM stator can exhibit only <1% smaller efficiency compared with the existing PS-FRPM machines with SPM inner stator. [ABSTRACT FROM AUTHOR]

The local magnetic saturation in tooth-tips of surface-mounted permanent magnet (SPM) machines generates on-load terminal voltage distortion, especially when small or closed slot openings are adopted. This paper focuses on investigating the influence of slot and pole number (Ns/2p) combinations on this phenomenon in both fractional slot and integer slot SPM machines. The mechanism of this phenomenon and how it is influenced by current advance angle and tooth-tip geometric parameters are introduced first. Then, voltage distortion pattern is proposed to analyze the occurring time or rotor positions of voltage ripples and their relative amplitudes according to the winding arrangements of different Ns/2 p combinations, with the influence of PM leakage flux considered. By 2-D finite-element analysis, the voltage distortion of various machines is calculated and compared, such as Ns \pm 1 = 2p, Ns \pm 2 = 2p, N s/2p = 3/2 (3/4), and integer slot machines with slot number per pole per phase q = 1 or 2. The analysis results reveal that under the same comparison conditions, the integer slot machines have less voltage distortion than the fractional slot machines, especially when q \geq 2. Meanwhile, for the same slot number, the fractional slot machines with Ns > 2p suffer from on-load voltage distortion less than their counterparts with Ns < 2p. Finally, three prototype machines with 12/10, 12/14, and 12/8 slot/pole numbers are manufactured and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

The on-load voltage distortion in fractional slot surface-mounted permanent magnet machines refers to the phase terminal voltage distorted by armature reaction. With the aid of frozen permeability method, the mechanism of this phenomenon has been investigated based on a 12-slot/8-pole model as an example, showing that the local magnetic saturation in tooth-tips is the main cause, especially when small or closed slot openings are adopted. Then, its impacts on machine performance under vector control have been investigated. If the dc-link voltage is sufficient to satisfy all distorted voltage, i.e., operating in constant torque region, the phenomenon mainly contributes to torque ripple. However, it becomes more problematic in the flux weakening region if the dc-link voltage is limited. Both base-speed and torque-speed curve will significantly differ from the expected results calculated by fundamental voltages. Meanwhile, if the machine operates beyond the base speed, or considering the limited bandwidth in real systems, the phase currents may be distorted, which consequently increase the current harmonics and reduce the average torque. Finally, a prototype machine is manufactured and tested to validate the analyses. [ABSTRACT FROM AUTHOR]

A rotor shaping technique with optimal third harmonic is presented to enhance the average torque of interior permanent-magnet (IPM) machines in this paper. The optimal value of third harmonic injected into the rotor outer surface shape has been derived and further confirmed by both finite-element analyses and experiments. The impact of the optimal third harmonic to the rotor shape on the electromagnetic performance, including harmonics in the back electromotive forces, cogging torque, average torque, and torque ripple, is investigated. It is demonstrated that without any modification of the costly rare earth permanent magnet employed for the inverse-cosine-shaped rotor, the average torque of the machine of an inverse cosine injected with an optimal third-harmonic-shaped rotor can be improved by > 6%. Simultaneously, the torque ripple remains almost unchanged, and the saliency ratio is also improved, further boosting the average torque. Finally, the machines with both conventional and optimal third harmonic rotors are prototyped and tested to validate the analysis. [ABSTRACT FROM PUBLISHER]

This paper presents optimal third harmonics in both permanent magnet (PM) shaping and current waveform to improve the output torque of five-phase surface-mounted PM (SPM) machines. The optimal value of third harmonic injected into the sinusoidal PM shape and current waveform for maximum torque improvement is analytically derived and validated by both finite element (FE) analyses and experiments. It is found that the optimal third harmonic is 1/6 of the fundamental one for both PM shape and current waveform. For the five-phase SPM machines having rotors without shaping, Sine shaping, or Sine shaping with third harmonic injected, the electromagnetic performance including the back EMF waveform, cogging torque, average torque, torque ripple, copper loss, iron loss, impact on power inverter, and demagnetization withstand capability are compared. It is demonstrated that, although the copper loss and iron loss increase due to additional third harmonic in the winding current and magnet shape, the average torque with optimal third harmonics injected in PM shaping and current waveform can be improved by >30% while the torque ripple and remains similar to that of the one with Sine shaping. In addition, this will reduce the dc bus voltage while maintaining the machine torque density. Furthermore, the machine with Sine and Sine+3rd rotors presents much better demagnetization withstand capability performance than conventional rotor. [ABSTRACT FROM PUBLISHER]

This work presents a permanent magnet (PM) shaping technique with optimal third harmonic to improve the output torque without deteriorating the torque ripple in surface-mounted PM (SPM) machines. The optimal value of third harmonic injected into the sinusoidal PM shape for maximum torque improvement is analytically derived and confirmed by finite-element analysis. Further, the influence of magnet edge thickness on the airgap field distribution is investigated and utilized to compensate the inter-pole flux leakage and curvature effect. It is found that the optimal third harmonic is 1/6 of the fundamental one. For the SPM machines having rotors without shaping, Sine shaping, Sine shaping with third harmonic injected, the electromagnetic performance, including the back-EMF waveforms, cogging torque, average torque, and torque ripple are compared. It is demonstrated that the average torque in the machine of a Sine shaping with an optimal third harmonic injected can be improved by >9\%, while the torque ripple remains similar to that of the one with Sine shaping. Finally, the machines with both conventional (without shaping) and optimal third harmonic PM rotors are prototyped and measured to validate the analyses. [ABSTRACT FROM PUBLISHER]

The paper investigates the influence of slot/pole number combination and winding configuration on the electromagnetic performance, such as flux density, back-EMF and electromagnetic torque, of permanent magnet machines having static or rotating rotor eccentricities. It shows that the eccentricity does not affect the back-EMF and electromagnetic torque of rotational symmetrical machines whose configuration repeats every certain amount of angle. However, it significantly distorts the back-EMF and torque waveforms of rotational asymmetric machines. Further, the static eccentricity does not change the harmonic contents of back-EMF, but results in unbalanced three phase back-EMF. Hence, the temporal order of the main torque ripple due to the static eccentricity is equal to the pole number. On the other hand, the rotating eccentricity results in more back-EMF harmonics of orders equal to the PM magnetisation order plus/minus one. Therefore, the temporal order of the main torque ripple due to the rotating eccentricity is equal to the triplen number closest to the pole number. The prediction is validated by the experiment. [ABSTRACT FROM PUBLISHER]

In order to improve the electromagnetic performance and ease the manufacture process, particularly stator winding, it is often preferable to employ a modular stator, e.g., individual stator tooth/back-iron segments, or separate stator tooth segments and back-iron segments. However, due to manufacture limits, there always exhibit additional air gaps between the stator teeth and back-iron segments. In practice, such gaps are likely to be nonuniform due to manufacture tolerances. This paper investigates the influence of uniform and nonuniform additional gaps on the cogging torque of permanent-magnet machines having either unskewed or step-skewed rotors. It is found that the presence of these gaps increases the cogging torque magnitude due to increased flux leakage through the tooth tips, while the uneven gaps can cause a significant increase in both the peak and periodicity of cogging torque waveform, which causes the skew method ineffective, as confirmed by both finite-element analyses and experiments. [ABSTRACT FROM PUBLISHER]

The paper presents an analytical model for predicting the open-circuit magnet eddy-current loss due to slotting in surface-mounted permanent-magnet machines based on the exact subdomain field model. The spatial and temporal characteristics of field harmonics due to slotting and corresponding eddy-current harmonics in the magnet are analyzed in both stator and rotor reference frames. The contribution of interaction between eddy-current harmonics having the same frequency but different spatial order to magnet loss is revealed for the first time by an analytical model. The magnet loss can be under- or overestimated if the interaction is neglected. The developed model is capable of providing both high accuracy and insights of loss generation. The influence of the slot and pole number combination, slot-opening to slot-pitch ratio, pole-arc to pole-pitch ratio, circumferential segmentation, and rotational symmetry order on the open-circuit magnet is investigated using the developed model. The finite-element results validate high accuracy of the developed analytical model. [ABSTRACT FROM PUBLISHER]

This article first proposes a generalized decomposition model for dual three-phase (3-ph) permanent magnet synchronous machines (PMSMs) with 0°, 30°, and 60° angle displacements between two sets of windings, allowing machines controlled in two-dimensional orthogonal αβ and xy subspaces. This model can decouple mutual inductances coupling phases from two sets, respectively. However, there often exist asymmetric impedances, due to inherent asymmetric machine parameters, cables with unequal lengths, manufacture tolerances, etc., in dual 3-ph PMSMs inevitably causing unbalanced phase currents and deteriorating the decoupling performance of the generalized machine model. Therefore, the generalized decomposition model incorporating asymmetric impedances is further developed, in which additional terms incurred by asymmetric impedances lead to the cross-coupling of αβ subspace and xy subspace. Through this model, the compensation capability of asymmetries is derived at a given dc link voltage. Then, a compensation strategy is illustrated to suppress unbalanced phase currents together with current harmonics caused by nonlinearities. Finally, experimental results testify the current balancing performance and simulation results further validate the machine model and the compensation capability. [ABSTRACT FROM AUTHOR]

Design rules of multiple multiphase winding configurations are investigated from the perspective of phase shift between adjacent winding sets in flux-switching permanent magnet (FSPM) machines. The relations between torque/rectified voltage and phase shift for any multiple multiphase winding topology are theoretically derived, directly showing the influence of phase shift on torque/rectified voltage harmonic components. It can be learned that the optimal phase shift for the lowest torque ripple and dc voltage oscillation depends on the winding types. Symmetrical winding is not always appropriate for any occasion. To verify the analytical results, the static characteristics of the dual three-phase, four three-phase, triplex three-phase, dual six-phase, and triplex four-phase FSPM machines with specific stator/rotor-pole combinations are studied by finite-element (FE) analysis. The FE-predicted dominant torque ripple and rectified voltage pulsation components for symmetrical and asymmetric phase shifts are in good agreement with the theoretical derivation. Prototypes are built and tested to verify the analytical and FE results. [ABSTRACT FROM AUTHOR]

In this paper, in order to enlarge its torque density, an overlapping winding (OW) is applied to the 24/16-stator/rotor-pole flux-switching permanent magnet (FSPM) machine. By adopting an OW-configuration with full-pitch coils, the pitch factor and coil-flux cross-sectional area in the 24/16-pole FSPM machine with nonoverlapping winding (NOW) can be doubled. Thus, the fundamental open-circuit phase flux-linkage and back-EMF can be effectively enhanced by 115.28%, making it comparable to the conventional 12/10-pole NOW-FSPM machine. Therefore, by injecting the same current density, the proposed OW-FSPM machine can produce 65.2% higher torque density than its NOW counterpart, and 17.6% higher torque density than the conventional 12/10-pole NOW machine despite 21.5% lower ampere turns due to a smaller slot area. However, the proposed machine suffers from high torque ripple due to high cogging torque and back-EMF harmonics. Torque ripple reduction by harmonics current injection and rotor skewing in the proposed machine are investigated. Results show that both methods can effectively reduce the torque ripple in the proposed 24/16-pole NOW-FSPM machine, albeit with the level of torque density being compromised. Experiments are performed in order to validate the analysis. [ABSTRACT FROM AUTHOR]

This article investigates some novel modular consequent pole PM machines (CPMs) with E-core and C-core stators. Different slot-pole number combinations including 12-slot/10-pole (Ns>2p) and 12-slot/14-pole (Ns<2p) have been investigated. Their static and dynamic electromagnetic performances have been investigated, e.g. the phase back-EMF, on-load torque, torque-speed curves, power factor-speed curves and also efficiency maps are compared. It is found that the existence of flux gaps (FGs) can improve the average torque of the 12-slot/14-pole E-core modular CPMs while the C-core structure can be a better candidate where relatively low torque ripple is desirable. Moreover, by selecting proper FG width, the 12-slot/14-pole E-core modular CPMs can achieve better flux-weakening capability and higher efficiency while the 12-slot/10-pole C-core modular CPMs can have higher power factors over the whole speed range. The finite element simulation results have been validated by a series of experiments using 12-slot/14-pole modular CPMs with both C-core and E-core stators. [ABSTRACT FROM AUTHOR]

This paper analytically derives the optimal third harmonic current to improve the output torque in five-phase surface-mounted permanent magnet (SPM) machines under the constraints of the same peak/rms value. The relationship between the output torque and the third harmonic current is established and its optimal value for maximizing the output torque is derived. It is found that the optimal third harmonic current is dependent on the ratio of the third harmonic back electromotive force (EMF) to the fundamental one but it is not 1/6 of the fundamental one as pulse width modulation in an inverter. In order to improve the output torque by increasing the fundamental and third harmonic winding factors and the third harmonic airgap flux density, the unequal width tooth and permanent magnet (PM) segmentation are employed in the 10-slot/8-pole five-phase SPM machine. The optimal unequal tooth dimensions and the number of PM segmentations are analyzed for maximizing the output torque. The airgap flux density, back EMF, cogging torque, and output torque of the machine with equal/unequal tooth width and unsegmented/segmented PM are compared. Finally, the experiments on the prototype 10-slot/8-pole PM machine with unequal tooth width and segmented rotor are given to verify the analytical and finite element analyses. [ABSTRACT FROM AUTHOR]

This paper investigates the interaction of the zero sequence component into both permanent magnet (PM) shape and phase current to improve the output torque in dual three-phase surface-mounted PM (SPM) machines. The optimal zero sequence components are analytically derived and validated by finite element (FE) analyses. It is found that the optimal zero sequence components into both PM shape and current waveform are dependent on the fundamental and zero sequence harmonic winding factors. For the dual three-phase SPM machines having rotors without shaping, Sine shape, Sine shape with the zero sequence components, the electromagnetic performances including the back electromotive force (EMF) waveform, cogging torque, average torque, and torque ripple are compared. It is demonstrated that the average torque with the optimal zero sequence component in PM shaping and current waveform can be improved by >30% while the torque ripple remains similar to that of the one with Sine shaping. Finally, the experiments are given to verify both the analytical and FE analysis. [ABSTRACT FROM AUTHOR]