Search

In this study, the in situ sol–gel method has been deployed to prepare the titanium dioxide/multiwalled carbon nanotubes (TiO2/MWCNTs) nanocomposite (NCs) powders with varying content of MWCNTs (0.01–1.0 wt %), to construct the dye-sensitized solar cells (DSSCs). First, binder-free NCs were deposited on a transparent-conducting F:SnO2 (FTO) glass substrate by a doctor-blade technique and then anchored with Ru(II)-based dyes to either N719 or ruthenium phthalocyanine (RuPc). The structural and optical properties and interconnectivity of the materials within the composite are investigated thoroughly by various spectral techniques (XRD, XPS, Raman, FT-IR, and UV–vis), electron microscopy (HRTEM), and BET analysis. The experimental results suggest that the ratio of MWCNTs and TiO2 in NCs, morphology, and their interconnectivity influenced their structural, optical, and photovoltaic properties significantly. Finally, the photovoltaic performances of the assembled DSSCs with different content of MWCNTs to TiO2 films anchored with two different dyes were tested under one sun irradiation (100 mW/cm2). The measured current–voltage (IV) curve and incident photon-to-current conversion efficiency (IPCE) spectra of TiO2/0.1 wt % MWCNTs (T@0.1 C) for N719 dye show three times more power conversion efficiency (η = 6.21%) which is opposed to an efficiency (η = 2.07%) of T@0.1 C for RuPc dye under the same operating conditions.

Nanoparticle embedded carbon nanotube papers can produce flexible functional films, whose function is based on the electronic coupling of the nanoparticles with the network of carbon nanotubes. Here we report on the expansion of a synergistic light-free catalyst system that requires both the molecular wire capability of multi-walled carbon nanotubes and the piezoelectric properties of ZnO nanoparticles. The electron–hole pairs can be induced by the piezoelectric effect of ZnO nanoparticles under the effect of pressure. The strong oxidizing radicals interact with the electron–hole pairs and aqueous solution to induce the degradation of methylene blue without the requirement of light. This study highlights the use of nanoparticles for the piezoelectric – light free catalyst system and the limitations of increased nanoparticle loading on the catalytic degradation of methylene blue.

Polyhydroxy fullerenes such as fullerenol C60(OH)22–24 have helped to bridge the gap between fullerenes and their innate solubility issues, where fullerenol solubility in water is 50 mg/ml whereas C60 solubility is 1.3 × 10−11 mg/ml. The improved solubility of these fullerene derivatives allows them to be better integrated into composite materials. Here we investigated the transport properties of cross-linked fullerenol–polyvinyl alcohol membranes with the addition of maleic acid for increased stability. High humidity causes the mechanical properties of polyvinyl alcohol to decrease. Using fullerenol as a cross-linker, we were able to decrease the sorption of water with these PVA membranes.

Carbon nanotube papers have many potential applications from actuators to electrodes. Cross-linked papers with embedded nanoparticles are now being investigated for use in these applications. Here we report on the development of piezoelectric multi-walled carbon nanotube paper. The piezoelectric effect of the paper was enhanced by four orders of magnitude by embedding zinc oxide nanoparticles into the carbon nanotube network, resulting in a simple method for producing flexible piezoelectric carbon nanotube paper.

High content carbon nanotubes mats have been produced to a range of thicknesses and diameters by covalent bonded cross-linking of thiolated multi-walled carbon nanotubes. The Michael addition pathway was used to cross-link benzoquinone to thiol groups attached to the surface of the nanotubes. The mats were characterized by a variety of techniques including X-ray photoelectron spectroscopy, tensile strength as well as qualitative structural analysis by scanning electron microscopy. It was found that the optimum ratio by weight for cross-linking benzoquinone to thiolated carbon nanotubes was ca. 5:1. This work provided a simple route to the production of mats without high pressure processing or irradiation techniques generally used to produce Buckypaper which can require pressure control chambers, argon and hydrogen ion beams and high temperatures. The mat surface can be further functionalized with nanoparticles to form advanced carbon composite materials.

Large-scale production of pure carbon spheres, with diameters from 50 nm to 1 μm, has been achieved via direct pyrolysis of a wide range of hydrocarbons, including styrene, toluene, benzene, hexane, cyclohexane and ethene, in the absence of catalyst. Specific systematic studies using styrene as the feedstock indicate that the sizes of the resulting of carbon nanospheres can be controlled quite well by adjusting the experimental conditions. The resulting materials have been fully characterized using SEM, TEM, AFM, HRTEM, EDX, elemental analysis, density measurement, XPS, FTIR, XRD, Raman, and TGA. The results show that the spheres, which are 99% carbon, consist of concentric incompletely closed graphitic shells. The dangling bonds on the edges of the shells result in high chemical reactivity.

Bioinspiration: Polar assembly (a feature of many natural protein-based fibrous structures, such as actin, microtubules, intermediate filaments, and collagens) is demonstrated in a straightforward, synthetic, peptide-based fiber system of de novo design (see false-color confocal-microscope image of fibers). This finding opens up possibilities for engineering self-assembling soft materials from the bottom up and with nano-to-microscale precision.

Here we report on the construction and operation of a cross-linked aminated multi-walled carbon nanotube paper as a hydrogen sensor. The incorporation of palladium onto the surface of the paper resulted in p-type conduction as the resistance of the paper was measured, under exposure to hydrogen gas. When palladium nanocrystals were embedded into the cross-linked paper, n-type conduction was observed during hydrogen sensing. This investigation highlights the next stage in the development of functional nanotube paper.

With careful removal of acid-oxidative lattice fragments and use of acid–base titrations, the covalent reactivity of covalently bound carboxylic groups on multi-walled carbon nanotube surfaces has been directly confirmed, including intermediate states, for carbodiimide promoted amidation reactions.

Understanding the compatibility between spider silk and conducting materials is essential to advance the use of spider silk in electronic applications. Spider silk is tough, but becomes soft when exposed to water. Here we report a strong affinity of amine-functionalised multi-walled carbon nanotubes for spider silk, with coating assisted by a water and mechanical shear method. The nanotubes adhere uniformly and bond to the silk fibre surface to produce tough, custom-shaped, flexible and electrically conducting fibres after drying and contraction. The conductivity of coated silk fibres is reversibly sensitive to strain and humidity, leading to proof-of-concept sensor and actuator demonstrations., The use of spider silk in electronic devices is dependent on its compatibility with electrically conductive materials. Here the authors modify spider silk with carbon nanotubes to produce a strong, flexible and electrically conductive thread.