Search

Aluminum Lithium alloys are recuperating substantial interest from automotive and aerospace industries owing to their extraordinary specific strength as compared to conventional aluminum (2xxx, 6xxx, and 7xxx) alloys. The goal of the present investigation is to study AA 8090 joints produced with the unique solid-state welding technique friction stir welding (FSW). Tool pin profile induces remarkable influence on friction and further plastic deformation during FSW. Therefrom, the influences of three distinct but constant dynamic area conditioned tool pin geometries namely, square trapezoidal, hexagonal trapezoidal, and threaded taper on the resulting material flow patterns, mechanical properties, and the microstructure have been studied and discussed in detail. The FSW joint produced with hexagonal trapezoidal pin geometry delivered the highest joint resistance owing to grain refinement and almost flawless microstructure.

The growing demand for more environmentally friendly vehicles has led to an increased use of light materials in the transportation industry with the aim to reduce structural weight, fuel consumption, and gas emissions, thereby boosting cost-effectiveness and recyclable properties. Complex multi-material steel-based components would allow to improve mechanical properties and minimize weight even further. In particular, new sandwich materials made by steel outer skins and a polymeric internal layer seems very promising for obtaining mechanical performance and lightness at the same time. Unfortunately, traditional welding techniques, like arc welding, laser welding, and resistance spot welding, usually used to join steels and aluminum alloys, cannot be applied for these materials due to their peculiar nature. In this paper, the feasibility of Friction Stir Welding to join thin sandwich components made of two steel outer layers and an internal polymeric layer was assessed. Both a pin and a pinless tool were used to weld the upper and the lower surface of the joint in order to obtain solid state bonding of the metal and fusion welding of the polymer at the same time. © 2020 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by-nc-nd/4.0/) Peer-review under responsibility of the scientific committee of the 23rd International Conference on Material Forming.

Friction Stir Welding (FSW) is one of the most used solid-state welding processes in the aeronautical, aerospace, ground transportation and naval fields. Stationary Shoulder Friction Stir Welding (SSFSW) is a recently introduced variant of the process allowing lower heat input into the joints, with beneficial effects in terms of joint mechanical properties, microstructure and top surface finish. In the paper, lap joints produced by SSFSW and made out of AA6082-T6 aluminum alloy sheets have been analyzed with the aim to investigate the effect of the stationary shoulder on the lap joints surface, metallurgical, and mechanical properties. The lap joints produced by SSFSW have been compared to the ones produced by “conventional” FSW in order to highlight the differences between the two processes. The top surface of the joints obtained with the two processes has been quantitatively evaluated. Finally, a dedicated numerical model has been utilized to highlight the causes of the observed differences through the distributions of the main field variables, namely temperature, strain and strain rate. It was found that SSFSW results in narrower weld nugget and smaller areas involved by micro hardness reduction caused by smaller peak temperature and high temperature zone. Additionally, better surface quality was found for the joint welded by SSFSW with lower heights and flash, allowing to avoid subsequent finishing operations needed for most industrial applications.

A widespread usage of aluminum alloys for the fabrication of car-body parts is conditional on the employment of appropriate welding methods, especially if dissimilar welding must be performed with automotive steel grades. Dissimilar welding of aluminum alloys and steel grades poses some issues concerning the formation of brittle intermetallic compounds, difference in physical and chemical properties of the parent metals, and poor wetting behavior of aluminum. Friction stir welding is considered to be a reasonable solution to obtain sound aluminum/steel joints. A study on the join quality of dissimilar lap joints of steel and aluminum alloy sheets after friction stir welding is proposed here. A low carbon steel is joined with AA6016 aluminum alloy to study preliminarily the feasibility to assembly car-body parts. The joints, welded with tool rotation and feed rate varying in a wide range, have been studied from a visual examination and microstructural point of view. Optical microscopy has been used to characterize the microstructure of the examined sheets in as-received and welded conditions. Micro-hardness measurements have been carried out to quantitatively analyze the local hardness of the welded joints. Set welding process parameters are identified to assemble without the presence of macroscopic defects the examined steel and aluminum welded parts.

Friction Stir Welding is nowadays an established technique successfully used by many industries. However, most of the research and, consequently, most of the applications regard aluminum alloys and butt joints. T-joints are of high interest for different industrial sectors as aeronautical, aerospace, naval and ground transportation, for which joint integrity and low residual stress are extremely important. In this study, an experimental and numerical approach is proposed with the aim to study the peculiarities of the residual stress distribution and material flow occurring in FSW of CP-Ti T-joints. Experiments were carried out to assess the feasibility of the process and to acquire the temperature data needed for the validation of a specifically set-up numerical model. Peculiar numerical strategies have been defined in order to calculate the residual stress with affordable CPU time and to highlight the bonding surface between the skin and the stringer. Main findings include a longitudinal residual stress profile different from the one usually found for butt joints. The reasons for this behavior were explained through a deep investigation on the temperature distribution in space and evolution in time. Finally, the bonding surface between skin and stringer was highlighted together with the possibility of flow defects in the fillet area.

Widespread use of aluminum alloys for the fabrication of car body parts is conditional to the use of appropriate welding methods, especially if dissimilar welding must be performed with automotive steel grades. Friction stir welding (FSW) is considered to be a reasonable solution to obtain sound aluminum-steel joints. In this context, this work studies the effects of tool position and force control in dissimilar friction stir welding of AA6061 aluminum alloy on DC05 low carbon steel in lap joint configuration, also assessing proper welding parameter settings. Naked eye and scanning electron microscopy (SEM) have been used to detect macroscopic and microscopic defects in joints, as well as to determine the type of intermixture between aluminum and steel. The joint strength of sound joints has been assessed by shear tension test. Results point out that tool force control allows for obtaining joints with better quality and strength in a wider range of process parameters. A process window has been determined for tool force conditions to have joints with adequate strength for automotive purposes.

Friction Stir Processing (FSP) has been demonstrated feasible to create local Metal Matrix Composites (MMCs) in light alloys matrix. In this research, local MMCs were produced contextually to the weld using Friction Stir Welding (FSW). SiC particles were added to AA7075 lap joints by creating a proper groove on the top surface of the bottom sheet. Different welds were produced with increasing number of tool passes. The effect of the multiple passes was investigated through shear tests, macro and micro observations, average grain size and microhardness measurements. The welded joints were compared to a reference weld produced with no reinforcements. It was found that poor mixing between matrix and reinforcement phase is obtained with one tool pass. On the contrary, proper mixing is obtained with three tool passes, resulting in an increase in the maximum load in shear tests of 50% with respect to the reference conditions.

Manufacturing processes, as used for discrete part manufacturing, are responsible for a substantial part of the environmental impact of products. Despite that, most of metalworking processes are still poorly documented in terms of environmental footprint. To be more specific, the scientific research has well covered conventional machining processes, concerning the other processes there is a lack of knowledge in terms of environmental load characterization instead. The present paper aims to contribute to fill this knowledge gap and an energetic analysis of Friction Stir welding (FSW) is presented. Following the CO2PE! methodological approach, power studies and a preliminary time study have been performed in order to comply with the In-Depth approach. The influence of the most relevant process parameters is analyzed regarding the required FSW energy. Finally, a few potential improvement strategies to reduce FSW energy consumption are reported.

Tailored blanks characterized by variable thickness were friction stir welded (FSWed) with the aim to obtain constant joint properties along the weld seam, regardless of the thickness change. To pursue this goal, the heat input was kept constant by in-process control of tool rotation. A dedicated numerical model of the process was used to determine the tool rotation values as a function of the sheet thickness. The mechanical properties and the microstructure of the FSWed joints, produced with varying process parameters, were studied. It was found that the proposed approach can produce joints with uniform properties along the weld line in terms of stress–strain curve shape, joint strength, elongation at failure, and microstructure.

Two different in-process control strategies were developed and compared with the aim to produce AZ31 magnesium alloy joints by friction stir welding on sheet blanks with a non-uniform thickness. To this purpose, sheets with dip or hump zones were welded by either changing the rotational speed or the tool plunging in order to keep constant the value of the vertical force occurring during the welding stage of the process. The influence of the main process parameters on the tool force, the micro- and macromechanical properties, and the joints microstructures in the dip and hump zones were analyzed. The results showed that using the rotational speed change-based approach, the hump zones are subjected to increased heat input with consequent increase of the heat-affected zone extension and average grain size (up to 11 μm). On the contrary, using the tool plunge change-based approach, the weld seam thickness in the dip zones is reduced, resulting in a decreased joint strength, with respect to tool rotation approach, equal to about 18%.

Difficult to weld aluminium alloys can be effectively joined by different alternative processes. Friction Stir Welding (FSW), among the solid-state processes and adhesive bonding represent two very attractive techniques. They allow the production of highly resistant joints avoiding the formation of the typical fusion weld defects. The aim of this work is to identify, analyse and compare the mechanical properties of AA6016 aluminium alloy joints made out of 1 mm thick sheets. FSW lap joints were and epoxy bonded joints were produced. Using the FSW results as benchmark, the overlap required in the bonded joint was identified to ensure the same static strength. Once the geometric configurations of the joints are known, the static and dynamic resistance of welds and bonding have been compared.

In the present work, friction stir welding experiments on AZ31 magnesium alloy sheets, characterized by a variable thickness along the welding line, were carried out. The approach adapted during welding consisted in maintaining constant the heat input to the joint. To this purpose, the rotational speed of the pin tool was increased with decreasing thickness and decreased with increasing thickness in order to obtain the same temperatures during welding. The amount by which the rotational speed was changed as a function of the sheet thickness was defined on the basis of the results given by FEM simulations of the FSW process. Finally, the effect of the in-process variation of the tool rotational speed on the mechanical and microstructural properties of FSWed joints was analysed by comparing both the nominal stress vs. nominal strain curves and microstructure of FSWed joints obtained in different process conditions. It was observed that FSW performed by keeping constant the heat input to the joint leads to almost coincident results both in terms of the curve shape, ultimate tensile strength and ultimate elongation values, and microstructure.

In this study, two bonding criteria, previously used for porthole die extrusion, are applied to FSW starting from the local value of the main field variables calculated through a specifically developed 3D numerical model of the process. Their applicability and effectiveness have been assessed through an experimental and numerical campaign carried out with the main process parameters varying in a wide range. The pressure–time–flow criterion was demonstrated to be better suited for FSW processes when large welding speed is used.

Solid-state bonding occurs in several manufacturing processes, as Friction Stir Welding, Porthole Die Extrusion and Roll Bonding. Proper conditions of pressure, temperature, strain and strain rate are needed in order to get effective bonding in the final component. In the paper, a neural network is set up, trained and used to predict the bonding occurrence starting from the results of specific numerical models developed for each process. The Plata-Piwnik criterion was used in order to define a quantitative parameter taking into account the effectiveness of the bonding. Excellent predictive capability of the network is obtained for each process.

Lap joints of Ti–6Al–4V were produced and the effect of the main process parameters was studied through macro and micro investigations highlighting mechanical resistance, microhardness profiles, grain size and phase distributions. A dedicated numerical model was used to link the input process parameters to temperature and strain distributions and to the final microstructure in the welded joint. It is found that the strain produced in the stir zone by proper combination of process parameters plays a fundamental role in the final microstructure and mechanical properties of the joints.

A microstructural and mechanical investigation on lap joints welded by friction stir welding and made out of a 7075-T6 stringer and a 2024-T4 skin is presented. In particular, the metallurgical and mechanical properties of joints have been studied at different tool feed rates (V = 35, 50, 100 mm/min) and constant rotation speed (R = 500 r/min). Temperature distributions have been monitored during the process. It is found that in the welded area, the recrystallized zone (nugget) has an average grain size of about 3 µm and exhibits coarsened MgZn2 particles on grain boundaries. The maximum values of microhardness in the welded skin increase with the process temperature, while they just slightly vary with process temperature in the stringer. From the mechanical point of view, the joint welded at R = 500 r/min and V = 50 mm/min exhibits both the highest strength and average microhardness value in the welded area.

Friction Stir Welding (FSW) is a solid state welding process patented in 1991 by TWI; initially adopted to weld aluminum alloys, it is now being successfully used also for high resistant materials. Welding of titanium alloys by traditional fusion welding techniques presents several difficulties due to high material reactivity with oxygen, hydrogen, and nitrogen with consequent embrittlement of the joint. In this way FSW represents a cost effective and high quality solution. The final mechanical properties of the joints are strictly connected to the microstructural evolutions, in terms of phase change, occurring during the process. In the paper a 3D FEM model of the FSW welding process, based on a thermo-mechanical fully coupled analysis, is presented. The model, tuned both for the thermo-mechanical analysis and the phase transformation through experimental data, is able to predict the phase volume fraction in the typical zones of the joints at the varying of the main process parameters. The obtained results permit to assess that the tuned FEM model of the FSW process can be utilized as an effective design tool.

In the paper solid state bonding conditions obtained in friction stir welding (FSW) of AA5754-H111 butt joints are analysed, considering the so called zigzag line in the transverse section of the joints. A wide experimental campaign was carried out varying both tool advancing speed and tool rotational one. The effects of the process on the mechanical properties of the joint were highlighted and micro- and macro-observations were used in order to explain the reasons of the enhanced mechanical properties found for the welded material. Numerical results derived from a FEM model previously developed by the authors were utilised to point out the different mechanical and metallurgical behavior of the obtained joints.

In the paper, a numerical and experimental study was carried out to highlight the effect of the distance d between the weld seam and the reinforcement on the residual stress distribution in Friction Stir Welded AA6082-T6 structures. An L-shaped profile was welded to a sheet metal with varying tool rotation and distance d from the weld seam. The Cut Compliance method was used to determine the resulting longitudinal residual stress. A dedicated FE model for FSW was set up, validated and utilized to predict the longitudinal residual stress in the assembled part. The analysis allowed the identification of a few design guidelines in order to reduce the detrimental effects of the residual stresses.

Dissimilar lap joints were produced by friction stir welding (FSW) out of Ti6Al4V titanium alloy and AA2024 aluminum alloy sheets. The joints, welded with varying tool rotation and feed rate, were studied by analyzing the maximum shear strength, Vickers microhardness and optical observations. A dedicated numerical model, able to take into account the presence of the two different alloys, was used to highlight the effects of the process parameters on temperature distribution, strain distribution, and material flow. The combined analysis of experimental measurements and numerical predictions allowed explaining the effects of tool rotation and feed rate on the material flow. It was found that tool rotation had a larger impact on the joint effectiveness with respect to feed rate. A competition between material mixing and heat input occurs with increasing tool rotation, resulting in higher joint strength when lower values of tool rotation are used.

Aluminum sheets can be joined to composite materials with different techniques. Each of them has advantages and weak points over the others. In literature, new techniques and patents are continuously developed to overcome these difficulties. In the paper a new Friction Stir Welding based approach is proposed to mechanically join AA6082-T6 to self-reinforced polypropylene. The aluminum sheet is pre-holed along both the sides of the weld line. A pinless tool generates the heat and pressure needed to activate back-extrusion of the composite. Joints have been produced with varying hole diameter and pitch. The mechanical resistance of the joint has been evaluated and the different failure modes were identified. Finally, a numerical model was set up to study the process mechanics by calculating the distribution of the main field variables, i.e. temperature strain and nodal displacement.

The Piwnik and Plata pressure-time bonding criterion was applied to Friction Stir Welding, Linear Friction Welding, Porthole Extrusion and Roll Bonding. A neural network was set up, trained and used to predict the bonding occurrence starting from the main field variable distributions calculated through specific numerical models developed for each process. The analysis of the results permitted to predict the occurrence of solid bonding and to highlight differences and analogies between the processes in order to obtain sound solid welds.

Two different in-process control strategies, developed in order to produce sound joints in AZ31 magnesium alloy by Friction Stir Welding on sheet blanks with a non-uniform thickness, are presented and compared. To this purpose, sheets with dip or hump were machined and welded by either changing the rotational speed or the tool plunging in order to keep constant the vertical force occurring during welding. The mechanical strength of the joints was measured in the zones where the sheets before welding were characterised by different thicknesses. The sheets welded by the two different strategies are characterized by very similar ultimate tensile strength values. Finally, the results showed that the two approaches permit to successfully weld sheets with non-uniform thickness with a reduced loss in the mechanical strength.

The results of an experimental and numerical analysis on Friction Stir Welding of dissimilar lap joints made out of AISI304 and Ti-6Al-4 V thin sheets are presented. The mixed joints, welded with varying process parameters, have been characterized from a mechanical and metallurgical point of view. A numerical model able to take into account the behaviour of the two different materials has been used. The numerical results have been utilized to explain the joint properties and the occurring material flow. The effect of the heat input, tilt angle and sheets mutual position has been investigated. It is found that both hooking defects and tunnels may occur with incorrect choice of process parameters. Good nugget integrity is obtained when the titanium sheet is used as upper sheet and high heat input is conferred to the joint. Finally, welding speed influences the nugget morphology as low values contribute to minimize the formation of the hooking defect.

One of the most relevant aspects of friction stir welding is the possibility to weld different materials. In the present paper, the authors present an improved continuum finite element model for the simulation of friction stir welding processes aimed to obtain T joints, made of a stringer in AA7175-T73511 and of a skin in AA2024-T4. The model, taking into account the thermomechanical behaviours of the two different materials, is utilised to study the occurring material flow and residual stress state. Numerical results are compared with experimental observations: the model is able to predict the material flow, obtaining important information on the joint failure mode.

Spot welding can be considered a very common joining technique in automotive and transportation industries as it permits to obtain effective lap-joints with short process times and what is more it is easily developed through robots and automated systems. Recently the Friction Stir Spot Welding (FSSW) process has been proposed as a natural evolution of the already known Friction Stir Welding (FSW) process, allowing to obtain sound spot joints that do not suffer from the insurgence of typical welding defects due to the fusion of the base material. In the paper, a modified Friction Stir Spot Welding (FSSW) process, with a spiral circular movement given to the tool after the sinking stage, is proposed. A continuum based numerical model for Friction Stir Spot Welding process is developed, that is 2D Lagrangian implicit, coupled, rigid-viscoplastic. This model is used to investigate the distribution of the main field variables, namely temperature, strain and strain rate, as well as the Zener-Hollomon parameter which, in turn, strongly affects the Continuous Dynamic Recrystallization (CDRX) process that takes place in the weld nugget. Numerical and experimental results are presented showing the effects of the process parameters on the joint performances and the mechanical effectiveness of the modified process.