Search

Plasmonic cavities are widely studied for the large amplifications in fluorophore emission intensity that they can achieve. Exploiting these properties for biological sensing applications requires strategies to selectively insert the target antigen into a resonant cavity, which are often of similar size or smaller than the target molecule. Here we demonstrate that using relatively simple solution processing, cavity structures can be grown at the stochastic locations where antigen binding takes place, which yields large enhancements in fluorophore emission intensities and over an order of magnitude improvement in bioassay response. The fluorescence amplification generated by the in situ growth of plasmonic structures is sufficiently large to enable both single antigen and single low-quantum efficiency fluorophore detection. The simplicity of the process demonstrated negates the requirement for complex surfaces or geometries and is readily adaptable for a wide range of diagnostic applications.

In this work, ultra-bright fluorescent silica nanoparticles (NPs) labels have been shown to selectively bind to a model circulating tumour cell (CTC) line, MCF-7, a metastatic breast cancer by targeting epithelial cellular adhesion molecule (EpCAM) present on the MCF-7 cell membrane. Silica NPs approximately 40nm in diameter were doped with different concentrations of Cyanine5 dye molecules, using the reverse microemulsion method. The NPs were two orders of magnitude brighter than Cyanine5 free dye and the measured fluorescence intensity matched a homo-Förster Resonance Energy Transfer model. NPs were conjugated with anti-EpCAM antibody to the NP surface for immunospecific targeting. In flow cytometry experiments the NPs were twice as bright as two commercial anti-EpCAM red fluorophore conjugates, APC and AlexaFluor®647. This increase is achieved while keeping non-specific binding low as established in control tests with a non-metastatic cancer cell line (HeLa). The NPs were also immunospecific in fluorescence microscopy experiments performed at room temperature on non-fixed cells. Confocal microscopy was used to confirm the NPs were located on the surface of the cells, matching with the location of the EpCAM marker. These NPs labels have excellent potential in biomedical diagnostics, particularly when high signal to noise and good photostability are needed, for example, in point-of-care testing., (Copyright © 2016 Elsevier B.V. All rights reserved.)

Fluorescent silica nanoparticle (NP) labels are of great interest in biomedical diagnostics, however, when used in bioassays under physiological conditions they rapidly agglomerate and precipitate from solution leading to high levels of non-specific binding. In this work, using size and zeta-potential data obtained from Dynamic and Electrophoretic Light Scattering analysis, the improvement in colloidal stability of silica NPs under physiological conditions was correlated with an increase in the concentration of three additives: (1) a protein, bovine serum albumin (BSA); (2) a neutral surfactant, Tween 20®; and (3) a charged surfactant, sodium dodecyl sulfate (SDS). The number of BSA molecules present in the NP corona at each concentration was calculated using UV-Vis spectroscopy and a bicinchoninic acid protein assay (BCA). The optimal concentration of each additive was also effective in stabilizing antibody labeled fluorescent nanoparticles (αNPs) under physiological conditions. Using a fourth additive, trehalose, the colloidal stability of αNPs after freeze-drying and long-term storage also significantly improved. Both as-prepared and freeze-dried αNPs were tested in a standard fluorescence immunoassay for the detection of human IgG. The as-prepared assay showed a higher sensitivity at low concentration and a lower limit of detection when compared to a free dye assay. Assays performed with freeze dried αNPs after 4 and 22 days also showed good reproducibility., (Copyright © 2015 Elsevier Inc. All rights reserved.)

Fluorescent nanoparticle (NP) labels are of great interest for point-of-care medical diagnostics where high fluorescence signals combined with low limits of detection are required. In this work, hydrophilic and hydrophobic fluorescein dye derivatives were covalently doped into silica NPs. The NPs were prepared in a range of sizes from 16 to 80 nm using both ternary and quaternary microemulsion methods where the diameter varied linearly with changes in the water to surfactant ratio. The morphology and colloidal stability of the NPs were characterised using transmission electron microscopy and photon correlation spectroscopy; NPs doped with hydrophobic fluorescein dye were significantly smaller and more polydispersed. Optical properties including absorption, fluorescence and quantum efficiency were also determined. Representative NPs from each microemulsion method (ternary, Ø = 25 nm and quaternary, Ø = 80 nm) were tested as labels in a fluorescence based immunoassay for the detection of human IgG and human chorionic gonadotropin. Both sets of nanoparticle assays showed lower limits of detection and better coefficients of variance than a free dye label with good day to day reproducibility. The optimal surface coverage of detection antibody was also found to depend on the size of the nanoparticle.

In this work, gold-silica plasmonic nanohybrids have been synthesized as model systems which enable tuning of dye fluorescence enhancement/quenching interactions. For each system, a dye-doped silica core is surrounded by a 15 nm spacer region, which in turn is surrounded by gold nanoparticles (GNPs). The GNPs are either covalently conjugated via mercapto silanization to the spacer or encapsulated in a separate external silica shell. The intermediate spacer region can be either dye doped or left undoped to enable quenching and plasmonic enhancement effects respectively. The study indicates that there is a larger enhancement effect when GNPs are encapsulated in the outer shell compared to the system of external conjugation. This is due to the environmental shielding provided by shell encapsulation compared to the exposure of the GNPs to the solvent environment for the externally conjugated system. The fluorescence signal enhancement of the nanohybrid systems was evaluated using a standard HRP-anti-HRP fluorescence based assay platform.

Fluorescence lifetime (FL) analysis and fluorescence correlation spectroscopy (FCS) have been successfully employed to reveal detailed information about the internal architecture of fluorescent silica nanoparticles (NPs). The dual-component lifetime behavior shows a two-domain dye distribution in the NP as a function of solvent accessibility. The introduction of an undoped silica shell serves to stabilize the outer dye fraction that is manifest as an increase in lifetime. The FCS not only shows a size-dependent increase in the cross-correlation decay constant but also demonstrates a significant relaxation in the FCS signal with the introduction of an undoped silica shell.

Surface plasmon-coupled emission (SPCE) is a phenomenon whereby the light emitted from a fluorescent molecule can couple into the surface plasmon of an adjacent metal layer, resulting in highly directional emission in the region of the surface plasmon resonance (SPR) angle. In addition to high directionality of emission, SPCE has the added advantage of surface selectivity in that the coupling diminishes with increasing distance from the surface. This effect can be exploited in bioassays whereby a fluorescing background from the sample can be suppressed. We have investigated, both theoretically and experimentally, the SPCE effect for a Cy5-spacer-Ag layer system. Both the angular dependence of emission and the dependence of SPCE emission intensity on Cy5-metal separation were investigated. It is demonstrated that SPCE leads to lower total fluorescence signal than that obtained in the absence of a metal layer. This is the first experimental verification of the reduction in SPCE intensity compared to the metal-free case. Our results are in a good agreement with theoretical models. The validation of the theoretical model provides a basis for optimizing biosensor platform performance, particularly in the context of the advantages offered by SPCE of highly directional emission and surface selectivity.