Search

Abstract: Pockmarks form where fluids discharge through seafloor sediments rapidly enough to make them quick, and are common where gas is present in near-seafloor sediments. This paper investigates how gas might lead to pockmark formation. The process is envisioned as follows: a capillary seal traps gas beneath a fine-grained sediment layer or layers, perhaps layers whose pores have been reduced in size by hydrate crystallization. Gas accumulates until its pressure is sufficient for gas to invade the seal. The seal then fails completely (a unique aspect of capillary seals), releasing a large fraction of the accumulated gas into an upward-propagating gas chimney, which displaces water like a piston as it rises. Near the seafloor the water flow causes the sediments to become “quick” (i.e., liquefied) in the sense that grain-to-grain contact is lost and the grains are suspended dynamically by the upward flow. The quickened sediment is removed by ocean-bottom currents, and a pockmark is formed. Equations that approximately describe this gas–piston–water-drive show that deformation of the sediments above the chimney and water flow fast enough to quicken the sediments begins when the gas chimney reaches half way from the base of its source gas pocket to the seafloor. For uniform near-surface sediment permeability, this is a buoyancy control, not a permeability control. The rate the gas chimney grows depends on sediment permeability and the ratio of the depth below seafloor of the top of the gas pocket to the thickness of the gas pocket at the time of seal failure. Plausible estimates of these parameters suggest gas chimneys at Blake Ridge could reach the seafloor in less than a decade or more than a century, depending mainly on the permeability of the deforming near-surface sediments. Since these become quick before gas is expelled, gas venting will not provide a useful warning of the seafloor instabilities that are related to pockmark formation. However, detecting gas chimney growth might be a useful risk predictor. Any area underlain by a gas chimney that extends half way or more to the surface should be avoided. [Copyright &y& Elsevier]

Methods for predicting the permeability and elastic properties of hydrocarbon reservoirs containing natural fractures are important for the production optimization and seismic characterization of fractured reservoirs. Effective medium theories may be used for this purpose but need to be validated using numerical calculations of the fluid flow and seismic properties for realistic fracture networks. The prediction of effective permeability and elastic properties using effective medium theories of fractured media are compared with numerical simulations using a discrete fracture network (DFN) containing two sets of non-orthogonal vertical fractures. Discrepancies between the permeability obtained from the simulations and using effective medium theory are attributed to an oversimplified treatment of fracture interconnectivity in the effective medium theory used. The simulations indicate that the effect of interconnectivity on fluid flow varies with stress and flow direction. By contrast, the effective elastic compliances obtained from numerical simulation and effective medium theory are in good agreement, even for relatively complicated fracture networks. Although permeability and seismic anisotropy both vary with stress, the relation between them is not simple. The variation in reflection amplitude with offset and azimuth is found to be sensitive to the ratio of the normal to shear compliance of the fractures, whereas permeability is less sensitive to this ratio. For the DFN studied, the permeability rapidly increases at high level of stress due to dilation of the fractures when the in situ stress field is strongly anisotropic. [ABSTRACT FROM AUTHOR]

The properties of hydrocarbon reservoirs are generally derived from core experiments and use theories of fluid flow that normally assume homogeneous core properties. Reservoirs, however, are generally heterogeneous, and interpretations of the results of these experiments are likely to be unreliable if the core from which the data are derived is heterogeneous. This article examines experimentally immiscible displacement through well-defined permeability heterogeneities, modeled using 2-D visual models packed with clear beads of different permeabilities. The results indicated that the displacement patterns were dominated by capillary pressure effects and that they were different from those found in miscible systems. This understanding is needed, since in reservoir simulators, the simulator codes must contain the correct physics, and in core analysis, the effluent profiles must be correctly interpreted for sensible predictions. [ABSTRACT FROM AUTHOR]