Search

The present work describes a valuable tool for winemaking industry to measure the acidity parameters with rapid response, simple sample handling, with no or minimal pre-treatment. Thus, a sequential injection analysis (SIA) system with spectrophotometric detection was used as platform for the development of methodologies for the quantification of volatile and total acidity in wine samples. Both procedures make use of the same colour reagent, bromothymol blue (BTB) that changes its intrinsic colour in the presence of the acidity compounds. The volatile acidity value was attained with the separation of the volatile fraction of acids by means of a membrane separation technique, a gas-diffusion unit. For the total acidity value, the sample was merged with the colour reagent on the way towards detection. The fixed acidity is a result of the difference from the total and the volatile acidity. The presented tool displayed a low sample and reagent consumption, 346 and 102µL of sample and 37 and 32µg of BTB, for the volatile acidity (VA) and for the total acidity (TA), respectively. The observed limits of detection and quantification were 0.03 and 0.01gL -1 (VA) and 0.09 and 0.02gL -1 (TA) with high determination rates, 35 (VA) and 62 (TA) determinations per hour. The proposed system was successfully applied to the quantification of volatile, total and fixed acidity in white table wine samples. The obtained results were in good agreement with the ones obtained by the reference methods., (Copyright © 2017 Elsevier B.V. All rights reserved.)

The determination of iron and copper exploiting a microsequential injection lab-on-valve system with online spectrophotometric detection is described. A new, environmental friendly 3-hydroxy-4-pyridinone chelator, functionalized with a polyethylene glycol chain (MRB12) to improve water solubility, was used for iron determination. For copper determination, 1-(2-pyridylazo)-2-naphthol (PAN) was used. Different parameters affecting the formation of the complexes were studied, namely sample volume, reagent concentration, and buffer composition and concentration. The optimized conditions, 150µL of sample volume and 250mgL -1 of MRB12 for iron determination, and 200µL of sample and 120mgL -1 of PAN for copper determination, enabled an LOD of 15 and 18µgL -1 for iron and copper, respectively. The robustness of the developed procedure was assessed by the calculation of the relative standard deviation (RSD), 5% for iron determination and 2% for copper determination. The accuracy of the method was assessed comparing the results with two certified samples (RD<7.5%) and calculating recovery percentages with five river water samples (average<107%)., (Copyright © 2017 Elsevier B.V. All rights reserved.)

In this work, a total flow analysis system based on a novel solid-liquid extraction chamber is presented. This strategy enables all the main experimental procedures for the analysis of a solid sample to be performed automatically: enrichment of the liquid extract, sample treatment, filtration of the liquid extract from the solid sample, directing the extract towards detection, and finally cleansing of the chamber for the following solid sample to be analyzed. The chamber designed to be incorporated in the flow manifold presents two main features: it accommodates stirring bars for enhancing the extraction process, and it presents replaceable solid sample containers (a spare part of the solid-liquid extraction chamber) to easily replace the solid sample and therefore enhance sample analysis throughput. The chamber performance was assessed using two different solid samples, an ion exchanger resin and vegetable samples, focussing on proton and nitrate ion extraction, respectively. The main figures of merit achieved were relative standard deviation (RSD) and relative error values below 7 % for all determinations. The determination rate for vegetable samples was ca. 12 samples h -1 . The proposed strategy may be exploited to perform automatically the analysis of solid samples as it embodies a simple automatic strategy of a very important but time-consuming and laborious analytical operation. Graphical abstract TAS for solid liquid extraction and nitrate potentiometric determination of vegetable samples.

Described is a new method based on the concept of controlled band dispersion, achieved by hyphenating flow injection analysis with ESI-MS for noncovalent binding determinations. A continuous stirred tank reactor (CSTR) was used as a FIA device for exponential dilution of an equimolar host-guest solution over time. The data obtained was treated for the noncovalent binding determination using an equimolar binding model. Dissociation constants between vancomycin and Ac-Lys(Ac)-Ala-Ala-OH peptide stereoisomers were determined using both the positive and negative ionization modes. The results obtained for Ac-L-Lys(Ac)-D-Ala-D-Ala (a model for a Gram-positive bacterial cell wall) binding were in reasonable agreement with literature values made by other mass spectrometry binding determination techniques. Also, the developed method allowed the determination of dissociation constants for vancomycin with Ac-L-Lys(Ac)-D-Ala-L-Ala, Ac-L-Lys(Ac)-L-Ala-D-Ala, and Ac-L-Lys(Ac)-L-Ala-L-Ala. Although some differences in measured binding affinities were noted using different ionization modes, the results of each determination were generally consistent. Differences are likely attributable to the influence of a pseudo-physiological ammonium acetate buffer solution on the formation of positively- and negatively-charged ionic complexes.

In this work, aiming to develop a simple, inexpensive method for the determination of low bromate levels in water samples, a liquid waveguide capillary cell (LWCC) was coupled to a FIA system. The long optical path (100 cm) of the LWCC was used to improve the sensitivity and the limit of detection without resorting to any off-line or in-line preconcentration processes. The spectrophotometric determination was based on the oxidation of chlorpromazine by bromate in an acidic medium, resulting in the formation of a colored radical product. Sulfamic acid was added to the reagent for minimizing the interference of nitrite, and a chelating ion exchange resin was used to remove major cationic interferences. The developed system allowed the determination of bromate within the range between 1 - 20 μg L(-1) with a detection limit of 0.2 μg L(-1).

Incorporation of long path length liquid waveguide capillary cell (LWCC or LCW) into spectrometric detection systems can increase the sensitivity of these by orders of magnitude (up to 500 times), and consequently can reduce the detection limits. The combination of the long path length spectrophotometry with flow methodologies can provide analytical solutions for various challenges in the field of environmental, biochemical and food chemistry. In this present work, the analytical applications of the long capillary cells are summarised and critically discussed. A historical overview of the cell development is given; applications in different areas are presented and grouped by analyte type. Major improvements achieved based on the use of the LWCC in the analytical characteristics (like sensitivity and detection limit) are emphasised while some of the limitations are also discussed., (Copyright © 2012 Elsevier B.V. All rights reserved.)

Although present at low concentration in wine samples, proteins, have considerable technological importance, due to their capability of haze formation. The present work presents a methodology for the quantification of total protein in white wine in a sequential injection lab-on-valve system, exploiting the bead injection concept for solid phase extraction with spectrophotometric detection. The method is based on the retention of the proteins in the solid support, NTA (nitrilotriacetic acid) superflow beads, charged by Cu(2+). The change in the absorbance is monitored at 500nm at the surface of the beads after addition of the Folin-Ciocalteu's reagent (FCr). The developed method presented a sample consumption of 400μL per assay and a consumption of FCr and Cu(2+) solution of 25μL and 100μL per assay, respectively. It was possible to achieve a linear range up to 0.30g/L with a limit of detection and quantification of 0.03 and 0.10g/L, respectively. The proposed method was successfully applied to white wine samples., (Copyright © 2011 Elsevier B.V. All rights reserved.)

In this work, the coupling of a commercial monolithic column to a traditional low pressure FIA system is proposed for the analysis of theobromine, theophylline and caffeine in coffee brewed samples using UV detection. The parameters mobile phase composition, flow rate and loop volume were evaluated and discussed considering the various chromatographic parameters in order to enable resolution of the methylxanthines studied within the coffee brewed sample matrix. The analyses of methylxanthines in coffee brewed samples by the proposed methodology were in good agreement with those obtained by the reference procedure based on HPLC. Relative errors were below 6% for all samples analyzed. Detection limits in the selected experimental conditions were within 10(-6)M range for theobromine and theophylline, and 10(-5) M for caffeine. The determination rate of the three methylxanthines for coffee brewed samples was ca of 10 h(-1). The main advantage of the proposed flow system was the possibility to perform chromatographic separations in low pressure flow systems. This substantial improvement was achieved due to the compatibility of monolithic columns within the flow injection system surpassing in this way one of the main handicaps of traditional flow analysis systems. Additional features of the strategy presented were low cost, efficiency, high versatility and low reagent consumption comparing to HPLC methodologies usually followed in the case study herein presented., (Copyright © 2011 Elsevier B.V. All rights reserved.)

A sequential injection system with dual analytical line was developed and applied in the comparison of two different detection systems viz; a conventional spectrophotometer with a commercial flow cell, and a multi-reflective flow cell coupled with a photometric detector under the same experimental conditions. The study was based on the spectrophotometric determination of phosphate using the molybdenum-blue chemistry. The two alternative flow cells were compared in terms of their response to variation of sample salinity, susceptibility to interferences and to refractive index changes. The developed method was applied to the determination of phosphate in natural waters (estuarine, river, well and ground waters). The achieved detection limit (0.007 μM PO(4)(3-)) is consistent with the requirement of the target water samples, and a wide quantification range (0.024-9.5 μM) was achieved using both detection systems., (Copyright © 2011 Elsevier B.V. All rights reserved.)

This work exploits a multi-syringe injection analysis (MSFIA) system coupled with a long liquid waveguide capillary cell for the spectrophotometric determination of zinc and copper in waters. A liquid waveguide capillary cell (1.0m pathlength, 550 μm i.d. and 250 μL internal volume) was used to enhance the sensitivity of the detection. The determination for both ions is based on a colorimetric reaction with zincon at different pH values. The developed methodology compares favourably with other previously described procedures, as it allows to reach low detection limits for both cations (LODs of 0.1 and 2 μg L(-1), for copper and zinc, respectively), without the need for any pre-concentration step. The system also provided a linear response up to 100 μg L(-1) with a high throughput (43 h(-1)) and low reagent consumption and effluent production. The developed work was applied to natural waters and three certified reference water samples., (Copyright © 2011 Elsevier B.V. All rights reserved.)

Water treatment has become a source of concern as new pollutants and higher volumes of waste water must be treated. Emerging biological approaches, namely the use of bioreactors, for cleaning processes have been introduced. The use of bioreactors requires the development of efficient monitoring tools, preferably with real-time measurements. In this work, a couple of flow injection systems were developed and optimized for the potentiometric determination of fluoride to monitor a rotating biological contactor (RBC) bioreactor and a sequencing batch reactor (SBR) with off-line and on-line sampling. Both the RBC and the SBR bioreactors were set up for the biodegradation of the halogenated organic compound 2-fluorophenol and, as fluoride was a degradation byproduct, the process was monitored by following up its concentration. The described flow injection potentiometric methods enabled the fluoride determination within the required quantification range 0.10-100mM. The possible interferences from the growth medium were minimized in-line. The determination rate was 78 h(-1) for the off-line monitoring of RBC and 50(-1)h for the on-line monitoring of the SBR, with a sample consumption of 0.500 mL and 0.133 mL per determination, respectively. Furthermore, the overall reagent consumption was quite low. The accuracy of the system was evaluated by comparison with a batch procedure. The SBR efficiency was monitored both on-line by the flow system and off-line by HPLC, for comparison purposes., (Copyright © 2011 Elsevier B.V. All rights reserved.)

A sequential injection system to monitor glycerol in a Saccharomyces cerevisiae fermentation process was developed. The method relies on the rate of formation of nicotinamide adenine dinucleotide in its reduced form (NADH, measured spectrophotometrically at 340 nm) from the reaction of glycerol with NAD(+) cofactor, catalysed by the enzyme glycerol dehydrogenase present in solution. This procedure enables the determination of glycerol between 0.046 and 0.46 g/l, (corresponding to yeast fermentation samples with concentrations up to 50 g/l) with good repeatability (relative standard deviation for n = 10 lower than 2.2% for three different samples) at a sampling frequency of 25/h. The detection and quantification limits using a miniaturised spectrophotometer were 0.13 and 0.44 mM, respectively. Reagent consumption was of 0.45 mumol NAD(+) and 1.8 microg enzyme per assay, and the waste production was 2.8 ml per determination. Results obtained for samples were in agreement with those obtained with a high-performance liquid chromatography method.

The development of fast, automatic and less expensive methods of analysis has always been the main aim of flow methodologies. The search for new procedures that still maintain the reliability and accuracy of the reference procedures is an ever growing challenge. New requirements are continually added to analytical methodologies, such as lower consumption of samples and reagents, miniaturisation and portability of the equipment, computer interfaces for full decision systems and so on. Therefore, the development of flow methodologies meeting the extra requirements of water analysis is a challenging work. Sequential injection analysis (SIA) presents a set of characteristics that make it highly suitable for water analysis. With sequential injection analysis, most routine determinations in waters can be performed more quickly with much lower reagent consumption when compared to reference procedures. Additionally, SIA can be a valuable tool for analyte speciation and multiparametric analysis. This paper critically reviews the overall work in this area.

A flow system based on the multicommutation concept was developed for the determination of free and total sulfur dioxide in table wines, exploiting gas diffusion separation and spectrophotometric detection. The system allowed the comparison of malachite green and pararosaniline chemistries, using the same manifold configuration. Free and total SO(2) were determined within the ranges 1.00-40.0 and 25.0-250 mg L(-1), at determination throughputs of 25 and 23 h(-1), respectively. Employing the malachite green reaction, detection limits of 0.3 and 0.8 mg L(-1) were attained for free and total SO(2), respectively. Pararosaniline chemistry provided detection limits of 0.6 mg L(-1) for free SO(2) and 0.8 mg L(-1) for total SO(2). Relative standard deviations better than 1.8 and 1.4% were obtained by the malachite green and pararosaniline reactions, respectively. With regard to the two tested chemistries, 18 wines were analyzed and the results achieved by the pararosaniline reaction compared better with those furnished by the recommended procedure.

The present work explores the slurry sampling approach for automatic, flow-based plant analysis. For this purpose, pinch valves were introduced into a multi-syringe flow injection analysis manifold to provide the repeatable aspiration of a few microliters of plant suspension before the material was further processed through the flow system. For validation of the proposed approach, the determination of potassium by flame emission spectrometry was implemented. Several parameters were studied: the concentration of plant particles in the sample suspension and the utilization of matrix modifiers. Microwave digestion was also implemented; no significant difference was found when certified reference material was analyzed with or without the in-line digestion step. The system was successfully applied to 13 samples within a concentration range of 2.5 to 100 mg g(-1). A determination frequency of 28 h(-1) was achieved and the precision was better than 4.0% (n = 12).

A flow system with a multi-channel peristaltic pump placed before the solenoid valves is proposed to overcome some limitations attributed to multi-commuted flow injection systems: the negative pressure can lead to the formation of unwanted air bubbles and limits the use of devices for separation processes (gas diffusion, dialysis or ion-exchange). The proposed approach was applied to the colorimetric determination of ammonium nitrogen. In alkaline medium, ammonium is converted into ammonia, which diffuses over the membrane, causing a pH change and subsequently a colour change in the acceptor stream (bromothymol blue solution). The system allowed the re-circulation of the acceptor solution and was applied to ammonium determination in surface and tap water, providing relative standard deviations lower than 1.5%. A stopped flow approach in the acceptor stream was adopted to attain a low quantification limit (42 microgL(-1)) and a linear dynamic range of 50-1000 microgL(-1) with a determination rate of 20 h(-1).

In the present work, an automatic flow procedure based on multi-syringe flow injection analysis was developed for the assessment of Folin-Ciocalteu reagent (FCR) reducing capacity in several types of food products using gallic acid as the standard. Different strategies for mixing of sample and reagent were tested (continuous flow of FCR, merging zones, and intercalated zones approaches); lower reagent consumption and higher determination throughput were attained for the merging zones approach (100 microL of sample+100 microL of FCR). The application of the proposed method to compounds with known antioxidant activity (both phenolic and nonphenolic) and to samples (wines, beers, teas, soft drinks, and fruit juices) provided results similar to those obtained by the conventional batch method. The detection limit was 0.6 mg L-1, and the determination frequency was about 12 h-1. Good repeatability was attained (RSD<1.3%, n=10).

A flow system was developed for the determination of total mercury concentration in fish samples by cold vapor atomic absorption spectrophotometry (CVAAS), based on the multicommuted flow injection analysis (MCFIA) approach. The system uses independently controlled solenoid valves for the introduction of reagents and samples. When not injected, solutions were recirculating to the reservoir bottles, in this way reducing the waste produced by the analytical system and also the sample consumption. Results were compared to those obtained by the reference flow injection procedure. Accuracy was also assessed by recovery studies using a certified reference material as well as spiked samples; recovery percentages in the range of 90.7% to 99.8% were found. The repeatability of the method was better than 6.0% (RSD, n = 10). A limit of detection of 4.8 microg of mercury per kg of fresh fish sample was achieved. The total waste produced was reduced to 30% of that from the reference flow injection CVAAS procedure.

A sequential injection system was developed for the enzymatic determination of ethanol in wine. The spectrophotometric determination is based on the enzymatic reaction catalyzed by alcohol dehydrogenase in the presence of NAD+. The system was applied to the determination of ethanol in a range of 0.008-0.024% (v/v) with good repeatability; RSD(n=10) < 2.3%. The results obtained with the developed system showed good agreement with those obtained by using the reference method. The determination rate was 25 h(-1); 1 micromol of NAD+, 1.1 units of enzyme, and 50 microL of sample were consumed per determination; and the waste produced was 2.2 mL per assay.

A flow injection multisite detection system was developed for correction of the sample blank in a colorimetric determination. By using detector relocation, a single spectrophotometer is used for the sequential reading of the sample blank and of the colored product; the sample crosses the flow cell to measure intrinsic absorption, the color reagent is subsequently added, and the flow cell is relocated to provide the reading of the resulting plug. The subsequent detector relocation immediately after peak maximum increases the determination frequency. This strategy was tested in the colorimetric determination of iron in soil samples based on the reaction of Fe (II) with 1,10-phenanthroline after reduction of Fe (III) to Fe (II) by ascorbic acid. The results obtained for 15 soil extracts were in good agreement with those obtained by the reference procedure. Relative standard deviations better than 4% were obtained, with a sampling rate of 30/h.

A multicommutated flow system was developed for the determination of aluminum in crystallized fruit samples. Spectrophotometric determination is based on the reaction of aluminum with chrome azurol S. The binary sampling technique was implemented to improve mixing conditions and to minimize reagent consumption. Three different working zones were established (0.5-5.0, 5.0-25.0, and 10.0-100 ppm) using the zone sampling approach, allowing us to adapt the extent of the in-line dilution. The influence of the chemical and physical parameters on the performance of the system was studied. Detection limits of 0.1, 0.6, and 0.8 ppm were obtained for the lowest, the medium, and the highest dispersion system, respectively. The procedure was applied to the determination of aluminum in crystallized fruit extracts. The results were in agreement with those obtained by the reference flame atomic absorption procedure at a 95% confidence level. Repeatability (RSD) was better than 2.4% in all of the three application zones.

A flow injection analysis (FIA) system was developed for the determination of phosphate efflux from wine lactic acid bacteria ( Oenococus oeni and Lactobacillus hilgardii) as an indication of cell membrane damage. The system allowed the direct injection of the cell suspension, avoiding the filtration step, with minimum sample treatment and minimized reagent consumption. The developed system is characterized by a linear concentration zone between 3.23 × 10−5 and 4.84 × 10−4 mol L−1 PO4 3− and repeatability better than 2.9%. Bacterial suspensions were exposed to a chemical stress with phenolic acids and injected in the FIA system at regular intervals. The extracellular concentration of phosphate was measured spectrophotometrically. The experimental results obtained indicate that hydroxycinnamic acids ( p-coumaric, ferulic and caffeic) induced faster phosphate leakage rates than hydroxybenzoic acids (vanillic and p-hydroxybenzoic) in both strains tested, which could be related to their higher lipophilic character. [ABSTRACT FROM AUTHOR]