Search

It is difficult to measure the cochlea directly because of the ethical problems and the complexity of cochlear structure. Therefore, finite element model (FEM) can be used as an effective alternative research method. An accurate FEM of the human ear can not only help people understand the mechanisms of sound transmission, but also effectively assess the effects of otologic diseases and guide research on the treatment of hearing loss. In this paper, a three-dimensional (3D) FEM of the human normal cochlea is proposed to study the changes in the biomechanical behavior of the cochlear sensory structure caused by the anterior fissure sclerosis and bottom-turn and apex-turn ossification of the cochlear window. The degree and harm of hearing loss caused by diseases are quantitatively predicted, which can deepen the understanding of the biomechanical mechanism of cochlea, and provide theoretical basis for clinical medicine. [ABSTRACT FROM AUTHOR]

Many studies have investigated factors contributing to large variations in the outcomes of round-window (RW) stimulation but most have focused on the floating mass transducer (FMT). To determine whether results for the FMT hold for a fixed-type transducer (FTT), this study constructs two coupled finite element models of the transducer and the human ear that incorporate the cochlear third windows and inner structures of these two electromagnetic transducers. We use these FE models of the human ear and transducers to investigate the influence of four design parameters and coupling conditions for the transducers, i.e., the support's Young's modulus, the coupling layer's cross sectional area and Young's modulus, and the transducer's cross sectional area. The results show that an increase in the support's Young's modulus reduces the output of the FMT but increases that of the FTT. Reducing the cross sectional area and Young's modulus of the coupling layer significantly increases the low-frequency response of the FMT but slightly reduces that of the FTT. Reducing the cross sectional area of the transducer increases the output of the FMT but reduces that of the FTT. This shows that inner structures of electromagnetic transducers should be considered in the optimal design parameters and coupling conditions for RW stimulation. [ABSTRACT FROM AUTHOR]

As a novel application of implantable middle ear hearing device, round-window stimulation is widely used to treat hearing loss with middle ear disease, such as ossicular chain malformation. To evaluate the influence of ossicular chain malformations on the efficiency of the round-window stimulation, a human ear finite element model, which incorporates cochlear asymmetric structure, was constructed. Five groups of comparison with experimental data confirmed the model's validity. Based on this model, we investigated the influence of three categories of ossicular chain malformations, that is, incudostapedial disconnection, incus and malleus fixation, and fixation of the stapes. These malformations' effects were evaluated by comparing the equivalent sound pressures derived from the basilar membrane displacement. Results show that the studied ossicular chain malformations mainly affected the round-window simulation's performance at low frequencies. In contrast to the fixation of the ossicles, which mainly deteriorates round-window simulation's low-frequency performance, incudostapedial disconnection increases this performance, especially in the absence of incus process and stapes superstructure. Among the studied ossicular chain malformations, the stapes fixation has a much more severe impact on the round-window stimulation's efficiency. Thus, the influence of the patients' ossicular chain malformations should be considered in the design of the round-window stimulation's actuator. The low-frequency output of the round-window simulation's actuator should be enhanced, especially for treating the patients with stapes fixation. [ABSTRACT FROM AUTHOR]

Conclusion: A tentative conclusion was made that the finite element method can be used to investigate the fatigue life of the tympanic membrane after ossiculoplasty; the main reason of the extrusion of the tympanic membrane may not be blamed to the fatigue mechanism under normal sound pressure. Objective: This study was to investigate the extrusion of the prosthesis from the tympanic membrane at post-ossiculoplasty by finite element method. Methods: A finite element model of the human middle ear has been constructed and used as the model of the constructed middle ear at post-ossiculoplasty. Then the fatigue life of the tympanic membrane was calculated under different sound pressure level using this model. Results: The tympanic membrane would not be extruded under normal sound pressure level. The sound pressure level which caused the tympanic membrane to crack in less than 3 years was higher than 145.17 dB (362.5 Pa). [ABSTRACT FROM AUTHOR]

Consisting of the actuator and coupling layer, a finite element model of the human middle ear was used to analyze the effect of the actuator and its coupling conditions on the performance of the eardrum-stimulated middle ear implants. This model which was based on the right ear of a healthy adult was built via microcomputed tomography imaging and the technique of reverse engineering. Based on this finite element model, the linear viscoelasticity of the human middle ear soft tissues and three-layer structure of the eardrum pars tensa which was orthotropic were considered. The validity of the model was verified by comparing the model calculated results with experimental data. After that, the influence of the three main design parameters of the actuator and two aspects of the coupling layer were investigated by the finite element model. The results show that (1) the manubrium tip is the optimal position for the actuator to stimulate; (2) the increased cross-section of the actuator would worsen its hearing compensation performance, especially in the low frequencies; (3) both the patients’ residual hearing and the actuator’s hearing compensation performance at high frequencies will be deteriorated with the increase in the actuator’s mass; and (4) a coupling layer with a small Young’s modulus and an area approximating 80% of the eardrum would reduce the stress of the eardrum effectively. [ABSTRACT FROM AUTHOR]

Finite element method was employed in this study to analyze the change in performance of implantable hearing devices due to the consideration of soft tissues' viscoelasticity. An integrated finite element model of human ear including the external ear, middle ear and inner ear was first developed via reverse engineering and analyzed by acoustic-structure-fluid coupling. Viscoelastic properties of soft tissues in the middle ear were taken into consideration in this model. The model-derived dynamic responses including middle ear and cochlea functions showed a better agreement with experimental data at high frequencies above 3000 Hz than the Rayleigh-type damping. On this basis, a coupled finite element model consisting of the human ear and a piezoelectric actuator attached to the long process of incus was further constructed. Based on the electromechanical coupling analysis, equivalent sound pressure and power consumption of the actuator corresponding to viscoelasticity and Rayleigh damping were calculated using this model. The analytical results showed that the implant performance of the actuator evaluated using a finite element model considering viscoelastic properties gives a lower output above about 3 kHz than does Rayleigh damping model. Finite element model considering viscoelastic properties was more accurate to numerically evaluate implantable hearing devices. [ABSTRACT FROM AUTHOR]

The lever ratio, the vibration mode and the stiffness of the ossicular joints were studied using the finite element (FE) analysis of the response of human ear under the outer ear sound excitation. The three-dimensional FE model was constructed based on serial micro CT images of a temporal bone block, and validated through comparison with the experimental data from previous literatures. The displacements of the umbo and stapes footplate and the vibration mode of the ossicles under different grades of stiffness of middle ear components were derived. It is suggested that the flexible ossicular joint combined with the shift of rotation axis causes the increase of lever ratio at high frequency. In addition, the flexible incudostapedial joint (ISJ) can reduce sound transmission especially at high frequency, meanwhile it also permits more vibration energy transmitted to the piston-like directions. [ABSTRACT FROM AUTHOR]

The finite element (FE) method was used to analyze the effect of coupling conditions between the actuator and the round window membrane (RWM) on the performance of round window (RW) stimulation. A FE model of the human ear consisting of the external ear canal, middle ear and cochlea was firstly developed, and then validation of this model was accomplished through comparison between analytical results and experimental data in the literature. Intracochlear pressure were derived from the model under normal forward sound stimulation and reverse RW stimulation. The equivalent sound pressure of RW stimulation was then calculated via comparing the differential intracochlear pressure produced by the actuator and normal ear canal sound stimulus. The actuator was simulated as a floating mass and placed onto the middle ear cavity side of RWM. Two aspects about the actuator coupling conditions were considered in this study: (1) the cross-section area of the actuator relative to the RWM; (2) the coupling layer between the actuator and the RWM. The results show that smaller actuator size can improve the implant performance of RW stimulation, and size requirements of the actuator can also be reduced by introducing a coupling layer between the actuator and RWM, which will benefit the manufacture of the actuator. [ABSTRACT FROM AUTHOR]

In this paper, a 3D finite element (FE) model of human cochlea is developed. This passive model includes the structure of oval window, round window, basilar membrane (BM) and cochlear duct which is filled with fluid. Orthotropic material property of the BM is varying along its length. The fluid-structure interaction (FSI) method is used to compute the responses in the cochlea. In particular, the viscous fluid element is adopted for the first time in the cochlear FE model, so that the effects of shear viscosity in the fluid are considered. Results on the cochlear impedance, BM response and intracochlear pressure are obtained. The intracochlear pressure includes the scala vestibule and scala tympani pressure are extracted and used to calculate the transfer functions from equivalent ear canal pressures to scala pressures. The reasonable agreements between the model results and the experimental data in the literature prove the validity of the cochlear model for simulating sound transmission in the cochlea. Moreover, this model predicted the transfer function from equivalent ear canal pressures to scala pressures which is the input to the cochlear partition. [ABSTRACT FROM AUTHOR]

Conclusions: The validated finite element model of human middle ear can be used as a tool in hearing loss research. Objective: To establish an accurate finite element model of the external ear canal and middle ear through micro-computer tomography and test its feasibility in the human. Methods: A fresh specimen of human temporal bone was scanned by micro-computer tomography. The finite element model was established based on the images, and then the simulation results were compared with published experimental data. Results: After a series of simulations were conducted, the simulated results were compatible with the published experimental data and this confirms the validation of the finite element model. [ABSTRACT FROM AUTHOR]